Page 1
III HD AdaptPro GMDN 41620 Patent NO2019050262 User Manual This product conforms to regulation MDR (EU)2017/745 for medical products. UM0136 UK 2022-10...
CONTENTS INTRODUCTION AREAS OF USE / INDICATIONS FOR NETTI AdaptPro CONTRA INDICATIONS QUALITY AND DURABILITY THE ENVIRONMENT AND WASTE DISPOSAL INFORMATION FOR RE-USE ABOUT THIS MANUAL VITAL MEASURES QUICK REFERENCE DESCRIPTION INFORMATION ABOUT NETTI AdaptPro SYSTEM HOW THE NETTI AdaptPro FRAME WORKS...
Page 3
DECREASE THE POSSIBILITY OF SLIDING, SHEAR AND PRESSURE SORES OPERATING RECLINE: RECLINING THE CHAIR BACK OPERATING TILT: TILTING THE SEATING UNIT PRACTICE THE USE OF THE NETTI AdaptPro TILT AND RECLINE SYSTEM TOGETHER WITH THE USER TRANSFER TO AND FROM THE WHEELCHAIR...
Page 4
LONG TERM STORING 10. TROUBLESHOOTING 11. TESTS & WARRANTY 11.1 TESTS 11.2 WARRANTY 11.3 CLAIM 11.4 NETTI CUSTOMIZED / INDIVIDUAL ADAPTATIONS 11.5 COMBINATIONS WITH OTHER PRODUCTS 11.6 SERVICE AND REPAIR 12. MEASUREMENTS & WEIGHT Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 5
Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
1. INTRODUCTION Netti AdaptPro is a tilt and recline wheelchair with seating system for adolescent and grown up users meant for mainly indoor and some outdoor use. It is tested to DIN EN 12183:2014. The tests were carried out by TÜV SÜD Product Service GmbH in Germany.
• The user has strong involuntary movements. persons with physical and/or mental disabilities. It is recommended the use of Netti Dynamic Netti AdaptPro has a modular system that can be System for these users. customized and adjusted according to the user’s need.
1.3 QUALITY AND DURABILITY 1.4 THE ENVIRONMENT AND WASTE DISPOSAL The Netti AdaptPro wheelchair is tested at TÜV Alu Rehab and its suppliers wish to protect the SÜD Product Service GmbH in Germany, following environment. the European Standard DIN EN 12183:2014.
For hygienic reasons: please replace the head support cover for a new user. Please also note the contents of Section 10.2 Cleaning and care. A refurbishment manual for Netti Wheelchairs can be downloaded at My-Netti.com A recycling manual for Netti Wheelchairs can be downloaded at My-Netti.com...
1.6 ABOUT THIS MANUAL In order to avoid damages while using the Netti AdaptPro wheelchair, please read this manual carefully before starting to use the chair. Symbol of forbidden actions. No warranty can be claimed whenever these actions are implemented.
1.7 VITAL MEASURES Netti AdaptPro is a comfort wheelchair designed for mainly indoor use, it can be used outdoor on smooth and level ground. Min. dimension in table refer to seat width 350 mm. Max. dimension refers to seat width 500 mm.
Page 12
– 10 mm 95 mm Parking brake Max slope – 7 ° Minimum turning radius, without leg supports R 500 mm R 560 mm Model with 24” main wheels. Measured without cushions. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 13
Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
The content of this page is a summary of the whole manual. It gives you a brief introduction to the use and care of the Netti AdaptPro wheelchair. The quick reference is not a replacement for the manual, only a reminder / check list.
Page 15
Product configuration may vary between Never lift the wheelchair by different countries. the leg supports, arm supports For visually impaired people, manuals or head support. and catalogues can be downloaded at www.My-Netti.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Be aware that specifications may vary between countries. If any of these parts are missing, please contact your dealer. For complete information, please contact your dealer. Be aware that illustrations and pictures may differ from your received product. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
The anti-tips follow the main wheels and are therefore always keeping the anti-tip security. Manoeuvrability: Netti AdaptPro has a very short wheel base of 375 mm when 3 ° forward tilt is used, ensuring easy manoeuvring in narrow spaces. The wheel base increases up to 465 mm when the chair is tilted 30 °...
TILT RANGE: The patented Netti AdaptPro wheelchair frame allows for extensive tilt range. On the Netti AdaptPro it is set from 3 ° forwards to 30 ° backwards. Model: Netti AdaptPro Language: English Version: 2022-10...
Page 21
The tilt cable from the tilt handle goes to a split box sitting on the frame. From the split box 2 wires – one to each cylinder are operated. Tilt cylinder adjustments see chapter 5.6. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 22
The back remains reclined in the position where you let the recline handle loose. Recline / dynamic gas cylinder adjustments see chapter 5.6. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
STANDARD OPTIONS / ACCESSORIES SEAT SEAT • Netti Sit cushion Cushion with good pressure • Trays & reading stand for trays (See chapter 5) distributing properties • Hip belts and 4 point belts harnesses • Tilt – 3 ° to + 30 °...
Grandis leg supports. UPHOLSTERY FOR TRAY Universal leg support Offers a soft base for the arm resting on the tray. WEDGE Increases side support. Angle adjustable leg support LUMBAR SUPPORT Increases lumbar curvature. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 25
ARM SUPPORT PADS Wide: 385 x 58 mm Support F with cheek / chin support band SIDE SUPPORT CORRECTION Meant for correction of unfavourable postures in the upper trunk. SIDE SUPORT STABIL Support Relaxo Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 26
Puncture proof Flexel or PU. Wheel frame extender 60 mm rearward position for the main 24” wheels. Wheel frame extender for rearward and height adjustment 16” main wheels FRONT WHEELS / CASTORS available in sizes: 7” Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 27
Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
2.8 kg done in the possible positions by standard Leg support Grandis right: 2.1 kg Netti Smart Back: 1.4 kg equipment, the adjustments will not exceed safe limits. Netti Sit: 1.0 kg Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Seat height is to be seen together with the leg supports and with the wheel positions. • Leg supports need to be adjusted to accommodate the seat height. Please note: the Netti leg support adjustments are described in detail in chapter 5.10. Please, see the drawings on next page regarding seat depth adjustments.
If the drive wheel does not lock, see chapter 5.3.6 and adjust. If it still does not lock, do not use the wheelchair but contact your dealer. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Pull the fork slightly to ensure that the fork is fully locked. Sand and sea water (salt used for gritting in the winter) can damage the bearings of the front castors. Clean the wheelchair thoroughly after exposure. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
If the depth has been increased, you need one pair of additional covers. If the depth has bee reduced you have one cover pair in spare. • Repeat on the other side. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Screw the set screw outward before. • Tightening the 2 bearing house clamping screws. • Replace the cover. • Repeat on the other side. Check angle of castor bearing house. 1 pc 5 mm Allen-key. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Adjust the nut backwards towards the axle head if the axle does not click in. Adjust the nut forwards if the axle sits loose when inserted through wheel and brake. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Tighten the wire clamp, and adjust the foot screw out again 1 pc 10 mm open-end spanner. To ensure the correct functions of the wire, these must never be taut. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• To release the brakes: lift the handles up. The user brakes cannot be used as running brakes. Do not leave the user in the wheelchair without activating the parking brake. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Loosen the hub bushing, including washer and nut, and mount it in required position in the main wheel bracket. The disc brake dolly must be positioned in the hole lower than the wheel bushing. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 38
1 pc 17 mm open-end spanner. Readjust the brakes (See chapter 5.3.6). • Mount the wheel hub to the extender. The AdaptPro frame is fitted with anti-tips which automatically follow the position of the main wheels. The anti-tips are delivered adjusted according to ordered main wheel size and standard position.
/ or position. See chapter 5.3.5. 5.4.4 NETTI SEAT PLATE The Netti Seat plate is an advanced seating platform developed to give persons sitting long time, improved comfort and reduction of seating problems.
Page 40
* With the back moved 25 mm forward. Please make a careful assessment of how the seat depth adjustments most favourable shall be made to keep good balance in the wheelchair. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Loosen the hinge screws on both sides and fix the back in the desired position. 2 pcs 6 mm Allen-key. Adjust the back cylinder position after the back hinge is moved. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
SEAT PLATE DEPTH SCALE: The seat plate a scale shows which seat depth has been chosen. With the chair-back moved to forward position the seat depth is 25 mm shorter than what the scale shows. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
1 pcs 5 mm Allen-key. By using the Velcro adjustment straps in the chair-back you can gain some mm on the depth. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 44
Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
When adjusting the seat plate length it is necessary to unfix the seat plate by loosening the brackets. Swing the seat plate up to get access to the screws for changing seat plate length as shown in chapter 5.4.6. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Tighten the straps so that they follow the curvature of the spine and give a little extra support at the top of the sacrum. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 47
• Mount the new Velcro by sliding it – with plastic rods – into the chair-back profiles. • Insert the set screw to hold the Velcro in place in the height. • Mount the back extender. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
5.5.3 BACK EXTENDER The back height of Netti AdaptPro is 510 mm measured from the seat plate to the top of the back Velcro. For users taller than around 1.85 m it may be advantageous to have a higher back for better support around the shoulder region.
BACK SUPPORT CYLINDER The chair back position is defined by the chair back cylinder. There are different cylinder strength available for the Netti AdaptPro: INDICATIVE correlation between body weight and suitable recline gas spring force: 450 N gas cylinder – 65 kg user weight 600 N gas cylinder –...
4 screws – shown green in the illustration. 1 pc 3 mm Allen-key. • Unhook the wires attached to the cylinder head. • Remove the cylinder by unscrewing it from the cylinder head. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 51
• Test if the new gas cylinder strength suits the user strength and is strong enough to calmly bring the user back to upright position when his / her extension movement ends. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
5.6.2 CHANGE OF TILT GAS CYLINDER The Netti AdaptPro is equipped with 2 tilt gas cylinders. The upper cylinder is the one taking much load. The lower is supportive to the upper cylinder. Both cylinder can easily be replaced in the same manner: •...
ASSEMBLING AND POSITIONING 5.7.1 NETTI HEAD SUPPORTS MOUNTING AND REMOVING: • To mount the Netti head support, lift up the red handle on top of the back gas cylinder. • Insert the 2 head support rods into the top. • Fix at any desired height by pushing the handle down.
5.7.2 NETTI DYNAMIC HEAD SUPPORT ADJUSTMENTS The Netti AdaptPro can be equipped with a Netti dynamic head support. The head support follows the backward movement of the head when the head is pressed against it. A small cylinder dampens the movement and brings the head back to normal position after extension.
There are 2 heights available with 58 mm distance. • Unscrew and position the arm support in desired height. • From the new rear arm support position, fine adjustments can be performed at the front. 1 pc 6 mm Allen-key. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
With the arm supports swung up there is good access to place sails etc. behind the back of the user. Always lock the brakes when you plan for actions and swing the arm support up. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
5.9 BELTS AND HARNESSES MOUNTING, POSITIONING AND ADJUSTMENTS OF PELVIC SUPPORTS AND SUPPORTIVE HARNESSES: Netti AdaptPro is prepared for mounting several different types of pelvic stabilizer and supportive harnesses, each type developed to give the user the best stabilization support depending on the conditions.
Page 58
H-BELT RACK FOR UPPER BODY HARNESS: Upper body harness rail is mounted to the chair- back profiles by separate brackets. See separate Mounting Description for upper body harnesses at: www.bodypoint.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 59
– follow the numbers. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 60
BELTS AND HARNESSES Article Description Pictures number for Netti Dynamic System BELTS / STABILIZERS Pelvic Stabilizer Evoflex M 82788 Medium Pelvic Stabilizer Evoflex L 82789 Large 4-point belt padded M 45013 Medium 4-point belt padded L 45014 Large HARNESSES Chest support Stayflex...
5.10 LEG SUPPORTS Netti AdaptPro is as a standard delivered with Netti Grandis leg supports. The chair can also be equipped with following alternative leg supports: • Grandis leg support • Universal leg support • Angle adjustable leg support standard •...
• Swing the leg support inwards and push slightly downwards until it clicks into locked position. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 63
GRANDIS FOOT PLATE ANGLE ADJUSTMENT: info@solidworks.com • Unfix the 2 screws as shown below using an 5 mm Allen-key. • Adjust the foot plate to the required angle and tighten the screws. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 64
For outdoor use, there should be a clearance of 40 – 50 mm between the foot info@solidworks.com plate and the ground. When adjusting leg support angle, be aware of squeeze hazard between moving parts. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 65
To adjust in depth of the calf pad, loosen the screw holding the calf support and slide it to required position before fixing the screw again. 5 mm Allen-key. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Grab around the vertical profile and thereby your hand is lifting the red lock lever. • Lift up and turn outward. Grandis Fixed leg support can also be delivered with a foot plate – to be ordered extra. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 67
• Details are also shown in chapter 5.10.2. 5 mm Allen-key. Never stand on the foot plates! Never lift the wheelchair by the leg supports. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Loosen the star wheel on the outside of the leg support. • Lift the lower part of the leg support to required angle. • Tighten the star wheel. Be aware of squeeze hazard between moving parts. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 69
• Loosen the screw on the outside of the foot plate – see picture – with an Allen-key. • Tilt the foot plate to required angle and tighten the screw. 5 mm Allen-key. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 70
For outdoor use, there should be a clearance of 40 – 50 mm between the foot plate and the ground. Never stand on the foot plates due to the risk of tipping forward. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 71
Loosen the screw B between the calf support and bracket and reposition it to required position before fixing the screw. 13 mm Allen-key. Never stand on the foot plates! Never lift the wheelchair by the leg supports. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 72
• Lift the right foot plate up. • Lift the leg support in the knee joint slightly up. • Swing it outwards. • Lift it up. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
5.10.5 NETTI DUAL LEG SUPPORTS NETTI DYNAMIC DUAL FEATURES: NETTI AdaptPro can be delivered with Netti DUAL Dynamic leg support. Netti Dynamic Dual leg support is especial designed for users pushing with uneven force with their lower extremities providing an open kinetic chain.
Page 74
FUNCTIONAL OVERVIEW: The Netti Dynamic Dual leg supports allow controlled open Kinetic Chain (oKC) movements of the lower extremities of the user. Unlike static wheelchairs, the user’s distal segments are supported but can move. This helps to gain control of the proximal segments especially when the user cannot inhibit movements due to their medical condition.
Page 75
Netti Dynamic Dual leg support is offered in 2 different lengths. Netti Dynamic Dual short leg support lengths suits persons with lower leg length from around 350 mm up to approximately 450 mm (measured when knees are 90 ° flexed, from underneath the thigh to under the heel –...
Page 76
Adjust the foot board height according to the lower leg length measured. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 77
Slightly tilting the seating unit may help. If not sufficient, the chair height must be adjusted as described in this user manual chapter 5.4. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 78
This will ensure that the user gets a good back support and pressure distribution under the thighs. Extension pieces allow for adjustments for different leg lengths. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 79
Twist the calf pads to an angle giving support for the leg when the foot support is angled. The calf pads can swing freely to follow the movements and adjust to the user’s leg position. 1 pc 5 mm Allen-key. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 80
They should in addition to supporting the calf also help prevent the feet sliding backwards from the foot-board. 2 pcs 13 mm open-end spanner. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 81
/ her feet. Lubrication of the gliding length profiles with white Vaseline is important to ensure smooth function of the Netti Dynamic system leg supports Dual. info@solidworks.com info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
The red star knobs allow locking the dynamic elevation of the leg support plate. For the dynamic use of the Netti Dynamic system (OK-C) this should be kept loose to allow for the knee joint to move (OK-C movement for the knee joint).
The extension piece is pulled forward and fixed in needed length on the side where the leg is longer. The leg support sits in the extension piece and is therefore also moved forward. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 84
5 mm Allen-key through the length profile into 2 nuts. 1 pc 5 mm Allen-key. info@solidworks.com Fix the foot-board lock with one M8 screw with 6 mm Allen-key. 1 pc 6 mm Allen-key. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 85
– suiting a user with longer right leg. All mounting illustrations are showed for Netti Dynamic Parallel. The mounting procedure for Netti Dynamic Dual is similar. info@solidworks.com Extension platform kit for Dual leg support: 82940 and 82941.
Position the bolt vertical into the frame hole turning it around 30 degrees outward for it to enter easy. Turn it inward until it clicks into user position. info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
The lock is closed by turning the outer ring 90 degrees forward! The foot-board lock MUST always be closed when the chair is occupied. info@solidworks.com LOCK info@solidworks.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
5.11 SIDE SUPPORTS Netti AdaptPro is prepared for fixing side support to the back tubes. • Fold the chair-back forwards by releasing the pin. • Insert square nuts into the back tube. At the top of the tube there is a wider space where the square nuts can fit into the groove.
5.12 ABDUCTION BLOCK Netti AdaptPro seat plate is prepared for mounting abduction block to the front of it. • Screw the abduction block to the seat plate in the nuts prepared for this. • Position it in the centre of the plate.
5.13 THIGH SUPPORT Netti AdaptPro seat plate is prepared for mounting thigh support to the top of it. They are fixed similar as the abduction block. 5.14 TABLE Netti AdaptPro can be fitted with a table. Since the arm supports follow the back...
Please use some time to study this manual and become familiar with the wheelchair and all its possibilities. Max. user weight for Netti AdaptPro is 160 kg. After the wheelchair has been correctly adjusted to the user described in the previous chapters, you as...
Wrong use of recline can cause loss of position, an increased risk of sliding, an increased danger of shear strain and The most shear is induced when going upright from a recline and tilted position. pressure sores. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Prototype is tilted. A tilt scale on the side of the chair shows which tilt angle has been chosen. Netti AdaptPro can be forward tilted – 3 ° and backwards tilted + 30 °. A backward tilted seat unit can create position, an decreased risk of sliding, an decreased danger of shear strain and pressure sores.
6.5 PRACTICE THE USE OF THE NETTI AdaptPro TILT AND RECLINE SYSTEM TOGETHER WITH THE USER • Practice using the tilt function leaning the complete seating unit backwards and forward, experiencing and testing how the user react. Tilt is recommended to be used for varying seating positions, leaning backwards for resting –...
/ or remove the head • Swing away the arm support on the side of the support. transfer. • Replace the components when the transfer is • Eventually remove the head support. finished. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Open the 2 handles holding the push bow and swing it to desired height before fixing them by pushing them down. The push bow can be swung up or down at any timer, reducing the length of the wheelchair. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
6.8.2 ANTI-TIPS Netti AdaptPro have anti-tips to ensure a safe and stable wheelchair at any time. They are pre-mounted and follow the position of the main wheels ensuring that the anti-tip function is active at any time. The anti-tips have a tramping pedal to be used for tipping the wheelchair backwards when passing obstacles.
6.8.3 BRAKES Netti AdaptPro is equipped with drum brakes that can be operated both with the brake handles on the push bar and from the parking / user brake in front of the main wheels. The brake handles on the push bow can be used as running brakes like on a bicycle.
6.8.4 ARM SUPPORTS Netti AdaptPro is equipped with swing away arm supports. LOCKING – UNLOCKING The arm supports are locked in a horizontal position to make sure the arm support does not unintentionally swing away. To unlock the arm support lock: Push the small red handle close to the elbow –...
Head support depth adjustment should be set by the therapist adjusting the wheelchair to the user. HEAD SUPPORT MOUNTING AND REMOVAL: The heads supports for Netti AdaptPro are easily info@solidworks.com mounted and removed: Open the latch on top of the back cylinder house.
6.8.6 LEG SUPPORTS – MOUNTING NETTI LEG SUPPORTS ARE MOUNTED LIKE THIS: Push the leg support fixing bolt vertical into the leg support fixing bracket on the wheelchair – keeping the leg support slightly turned outwards. The leg support will fall in place and turn into place itself.
6.8.7 LEG SUPPORT FOOT BOARD Netti Dynamic DUAL leg supports are equipped with a foot board. It is linked to the left leg support and folds down into a foot board lock in the right leg support. FOOT BOARD LOCK:...
6.8.8 LOCKING DYNAMIC LEG SUPPORTS The Netti Dynamic Dual Leg support angle can be locked by tightening the red wheel on the outside of the leg supports. See illustration: This stops dynamic movements except for the limited rotation of the foot-board.
Netti AdaptPro. Netti AdaptPro is prepared for mounting several different types of pelvic stabilizer and supportive harnesses, each type developed to give the user the best stabilization support depending on the conditions: •...
Page 105
ANKLE HUGGERS AND SHOE SHELLS are mounted to the foot board. They help to keep the feet on the foot board not letting them slide off the foot plates or foot board. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
ISO 7176-19:2008 stating it is suitable to be used as a seat in a vehicle. Before using the Netti AdaptPro as a seat in a car, be sure to remove and secure all auxiliary parts and accessories (eg. trays) that may fall off the chair in case of an accident and secure them safely elsewhere.
Page 107
Make sure the car safety pelvic-belt lay tightly across or in front of the pelvis – the Netti AdaptPro seat width 350 – 500 mm is angle between pelvic belt and the horizontal approved for user weight up to 135 kg when between 30 –...
Page 108
Netti AdaptPro with seat width 500 mm extension kit must be mounted when Netti and more, exceed the max width of 700 mm AdaptPro is used as a seat in a car. specified in PRM-TSI and have influence on the possibility for train transport.
3 gas cylinders. These are however not classified as dangerous The wheelchair should face opposite the direction of goods. Netti AdaptPro is configured with tilt and travel. The back of the wheelchair must be located recline functions which are activated with gas against a fixed object such as a row of seats or a spring(s).
By swinging the push bow up, the attendant can drive the wheelchair with large tilted / reclined position for shorter distances like transferring from room to room. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 112
The user could fall out of the chair the wheels may loose traction and it is difficult by the impact. The front castors could brake. to control the wheelchair. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Page 113
EMERGENCY ESCAPE ROUTES: Netti AdaptPro with seat width 500 mm and more, has an overall width exceeding 700 mm and may have difficulties passing emergency escape routes.
• Pull the wheelchair up by the push handles onto the step and go backwards long enough to put down the front castors on the step. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
• Put the front castors down on the ground. Move the upper part of the body backwards to maintain balance of the chair. Control the speed of the chair by clutching the push rims. Do not use the brakes. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
Techniques for transferring to / from the wheelchair and user, we do not recommend driving should be practiced well with the persons a Netti AdaptPro wheelchair up or down involved. Here, we give some important advices for stairs. preparation of the chair:...
Page 117
• Remove the leg supports. • Open the backrest angle slightly. • Replace the components when transfer is finished. Never stand on the foot plates due to the risk of tipping the chair forwards. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
(Chap 5.3) 2 pcs 24 mm open-end spanner. 5 mm Allen-key. The Netti AdaptPro main wheel bracket allows for changing wheel position and thereby changing the seat height. If required frame extenders bracket can be mounted to move the main wheel 60 mm backwards.
8.9 PUSH RIM Netti wheelchairs are delivered with aluminium push rims as standard. The material and distance to the main wheel influences the ability of the user to grip. Contact your dealer to get information about push rims that fit your chair.
Use methylated spirit to remove any dirt left. Clean cushions and covers according to instructions printed on cushions. Frequency Weekly Monthly NETTI CUSHION CLEANING PROCEDURES Check defects / damages e.g. breakage / missing parts CORE Washing of wheelchair Washing Hand wash 40 °...
DISINFECTION OF THE WHEELCHAIR SPARE PARTS Remove cushions. The Netti chairs are built of modules. Alu Rehab See separate washing instruction above: carries stock of all parts and is ready to supply these Wipe disinfection: use a soft rag wetted with on short notice.
When in need of spare parts, please contact your dealer. When making changes affecting frame construction, contact dealer / manufacturer for confirmation. Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
11. TESTS & WARRANTY 11.1 TESTS 11.2 WARRANTY Netti AdaptPro is tested and have been Alu Rehab is providing you with a 5-year warranty approved for both indoors and outdoors use. on all frame components and on the cross-tube The chair is CE marked.
11.4 NETTI CUSTOMIZED / INDIVIDUAL ADAPTATIONS If a product has developed a fault during the Netti Customized / individual adaptations are warranty period as result of a defect in design or defined as all adjustments that are not included in manufacturing, you may forward a warranty claim.
Alu Rehab. Substitutions or alterations of components from third part suppliers to Netti AdaptPro requires the risk evaluation and acceptance of the product responsibility and safety for use of the wheelchair from the manufacturer that is performing the substitution or alteration.
Information on product safety notices and product recalls are available at www.My-Netti.com A recycling manual for the wheelchair can be obtained through your local dealer or downloaded at www.My-Netti.com Model: Netti AdaptPro Language: English Version: 2022-10 My-Netti.com...
The cushions are not included. Recommended tyre pressure for pneumatic drive wheel tyres: 40 – 45 PSI. Max. user weight for Netti AdaptPro with seat width up to 500 mm: 135 kg. When used as seat in a car: Max. user weight 135 kg.
Page 128
Manufacturer of Netti: Designed in Norway Alu Rehab AS Bedriftsvegen 23 N-4353 Klepp Stasjon Norway post@My-Netti.com T: +47 51 78 62 20 my-netti.no Distributor Distributor Distributeur Alu Rehab ApS Meyra GmbH Meyra Netti SAS Kløftehøj 8 Meyra-Ring 2 11 rue du Bois du Pont...
Need help?
Do you have a question about the AdaptPro and is the answer not in the manual?
Questions and answers