Subscribe to Our Youtube Channel
Related Manuals for Netti DYNAMIC S
Summary of Contents for Netti DYNAMIC S
- Page 1 MOBILE FAMILY DYNAMIC SYSTEM C O M F O R T user manual netti DYnamiC s this product conforms to 93/42/eeC for medical products. my-netti.com...
-
Page 2: Table Of Contents
CONTENTS 1. INTRODUCTION Areas of use/indications for Netti Dynamic S Quality and durability Environment and disposal Information for re-use About this manual Vital measurements 2. QUICK REFERENCE 3. DESCRIPTION 4. FEATURES OF NETTI DYNAMIC SMALL 5. ACCESSORIES 5.2 Mounting of Hip Belt 5.3 Mounting of H-Belt bar... - Page 3 7. DYNAMIC FUNCTIONS Netti Dynamic S - max extension 72. Assessment and choice of dynamic back support cylinder 7.3 Tilting the seat unit 7.4 Reclining the chair back 7.5 Dynamic seat plate lock 8. MANOEUVRING Driving - general techniques 8.2 Driving - step up 8.3 Driving - step down...
-
Page 4: Introduction
Netti Dynamic S has an adjustable seat and back angle, thus facilitating for the user change of position, mobilisation or posture correction (stabilization). Netti Dynamic S is a tilt- and back recline wheelchair that allows for controlled «Open Kinetic Chain» (OK-C) movements for the user. -
Page 5: Areas Of Use/Indications For Netti Dynamic S
1.2 QuALITy AND DurABILITy 1.1 ArEAS of uSE/ The Netti Dynamic S wheelchair is tested INDIcATIoNS for at TÜV SÜD Product Service GmbH in NETTI DyNAmIc SmALL Germany, following the European Standard DIN EN 12183:2014. Netti Dynamic S is a multifunctional wheelchair which is an advanced mobility aid for users affected by dystonia. -
Page 6: Information For Re-Use
1.4 INformATIoN for rE-uSE In order to avoid damages while using All products from Alu Rehab are designed the Netti Dynamic S wheelchair, please to give years of maintenance-free service. read this manual carefully before starting All products can be adapted for re-use by to use the chair. - Page 7 1.6 VITAL mEASurES Specification min. max. Netti Dynamic S is a comfort wheelchair designed for both outdoor and indoor use. Overall length with leg support and push bow 905 mm 905 mm Specification varies between countries Overall length without leg...
-
Page 8: Quick Reference
If in doubt - contact your dealer! depth, chair back cushion height. For more information about adapting the wheelchair to the user, please see: My-Netti.com Knowledge centre. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 9: Description
25. Head support depth knob 11 12 13 14 * Product configuration may vary between different countries If any of these parts are missing, please contact your dealer. for complete information, please contact your dealer Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 10: Features Of Netti Dynamic Small
BAcKrEST • Angle: 35° BAcKrEST • Height: 375 mm • Backrest cushions Netti Stabil • Netti Super Stabil S back rest cushion has integrated lumbar support and side support, • Angle adjustable and fold down push bow BrAKES • Drum- and user brakes ANTI TIPPEr •... -
Page 11: Accessories
Side support for sw 25 Depth and height 4 point hip belts. adjustable. info@solidworks.com calf huggers on the calf supports. Ankle huggers Abduction block Netti Mini Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... - Page 12 Netti Nature Tool set Kit with 12” front wheel and frame to fix to netti Dynamic S, allows for driving outdoors The spare part and accessory catalogue and off-road. can be downloaded from our home page www.my-Netti.com...
-
Page 13: Mounting Of Hip Belt
• The hip belt bracket on the seat plate You find the anytime updated overview can be moved to 7 different positions over belts and harnesses on our home page .com providing the optimal position for the hip www.My-Netti.com belt. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 14: Mounting Of H-Belt Bar
The lower ends of the belts can be fixed like shown in chapter 5.1 4 mm Allen key for m6 screws with pan heads. 5 mm Allen key for m6 screws with cylinder head. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 15: Assembling And Adjusting
Main wheel 16” x 1,4”: 1,7 kg each Front castors 6”: 0,6 kg each Leg support: 2,1 kg (with foot board) Back cushion Super Stabil S: 1 kg Netti S Sit cushion: 0,8 kg Head support A Mini: 0,75 kg Necessary tools are described under each chapter. -
Page 16: Seat Height At The Front
6.6 SEAT HEIGHT AT THE rEAr readjust the angle of the bearing house. The seat height at the rear depends on: • Size of main wheel. • Position of main wheel. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 17: Backrest
See picture on next page The backrest hinge must be in the same positions on both sides. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 18: Adjusting The Seat Plate Depth
• Insert the screws and fix. Back hinge position Cylinder position • Replace all components. info@solidworks.com Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 19: Adjusting Seat Depth At The Front
By users with strong involuntarily movements the extension pieces must not be pulled out more than 50 mm. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 20: Adjusting The Velcro Back
Check that the back cushion cover on the back of the cushion for correct the side support with no hard edges. maintenance and washing of the cushion Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 21: Adjusting Arm Supports
Netti Dynamic leg support with whole foot user needs. plate is standard for Netti Dynamic S. Universal leg support and angle adjustable Warning: The adjustment should be carried leg support with foot plate and calf support are also available for Netti Dynamic S. - Page 22 Ankle huggers Netti Dynamic S leg support is especially developed to allow for uneven forces from The footboard has holes prepared for an- the legs. Unilateral extension of the hip (left kle huggers or shoe shells to be mounted or right part of the leg support goes down).
- Page 23 Netti Dynamic System Leg supports. Twist the calf pads to an angle giving sup- port for the leg when the foot support is Netti Dynamic SmALL has also the angled. The calf pads can swing freely to fol- following foot support alternatives low the movements and adjust to the user’s...
-
Page 24: Head Support
• Untighten the four screws holding the adapter together. • Move the adapter to the required position and fix the adapter by tightening the screws diagonally. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 25: Push Bow
To get the push bow out of the way it can be turned all the way down till it touches the chair back. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 26: The Brakes
6.20 THE BrAKES Netti Dynamic S with 16” drive wheels is equipped with drum brakes 3 operation modes • Parking brakes - with foot pedal, • User operated parking brakes - with handle. • Attendant brakes with brake handles on the... - Page 27 Tighten the nut A close to the head with the 17 mm open end spanner and fix the gas cyl- inder firmly. Fold up the back and fix the cylinder to it. Check all dynamic functions. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05...
-
Page 28: Dynamic Functions
Open Kinetic Chain movements (OK-C):: Head movements Back movements Hip movements Leg movements Foot movements With correct recline cylinder force, the wheelchair will bring the user up into normal position after a spasm. s.com Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 29: Netti Dynamic S - Max Extension
7.1 NETTI DyNAmIc SmALL mAx ExTENSIoN Headrest pushed backwards Back in max recline Seat lifted Frame extender Leg supports lifted and extended Tilted foot plate Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 30: Cylinder
If you recline the chair back on a wheelchair with free cylinder, locking it in reclined posi- tion, it is only the Netti Dynamic Leg sup- ports, seat plate and head support that will respond to spastic movements. - Page 31 Newton (N) 100 N 87909 15 kg 200 N 87911 20 kg 300 N 87913 30 kg 400 N 87915 40 kg 500 N 87917 50 kg 600 N 87919 60 kg Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05...
-
Page 32: Tilting The Seat Unit
The correct relative angle between the body To ensure correct function of the parts remain the same when the seating unit wires, these must never be taut. is tilted. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 33: Reclining The Chair Back
The seat unit can be reclined from 0° to +35°. FIXED DYNAMIC info@solidworks.com Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 34: Dynamic Seat Plate Lock
When driving a wheelchair with Netti ing the Netti Dynamic System to work. Dynamic System, careful driving is mandato- ry. Watch out for obstacles that could be in the reach if the dynamic parts of the wheel- chair is fully extended. -
Page 35: Driving - General Techniques
• Drive carefully down the step and move the wheelchair backwards on the main wheel until the front castors have come away from the step. • Put the front castors down on the ground. Turn the anti tip down. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 36: Driving - Slope
Move the upper part of the body on their back. backwards to maintain balance of the chair. Control the speed of the chair by clutching the push rims. Do not use the brakes. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 37: Driving - Down Stairs
• Lock the brakes. • Remove leg supports. • Tilt chair forward. The companions should use the strength in their legs carrying the chair, avoiding unnecessary stress on their back. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 38: Point Of Balance
8.10 cAmBEr ANGLE Netti Dynamic S has as standard no camber angle. When the main 16” wheels are replaced with 22” wheels, the necessary Never stand on the foot plates due to wheel frame extender bracket has 4°... -
Page 39: Transport
Sudden spastic Before using Netti Dynamic S as a seat in a movements may harm other passengers. car be sure to remove and secure all parts... -
Page 40: Transporting In Air Plane
2 gas springs. These are however not Spare parts: classified as dangerous goods. The Netti chairs are built of modules. Alu Contrary to general dangerous goods Rehab carries stock of all parts and is instruction UN3164, the IATA-DGR ( special ready to supply these on short notice. -
Page 41: Cleaning And Washing
ProcEDurES: CORE Washing Hand wash 40ºC Disinfection Virkon S Auto clave 105ºC Drying Squeeze Air dry standing edgewise OUTER COVER Washing Machine wash 60ºC Drying Tumble dry max 85ºC Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 42: Troubleshooting
When in need of spare parts, please contact your dealer. When making changes affecting frame construction, contact dealer / manufacturer for confirmation ahead of the fixing. Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05... -
Page 43: Tests And Warranty
Netti Dynamic S is tested and has been purchase of the wheelchair. approved for usage both indoors and • Generally, defects are accepted as outdoors. -
Page 44: Combination With Other Products
Alu Rehab. Substitutions or alterations of components from third part suppliers to Netti Dynamic SMALL requires the risk evaluation and acceptance of the product responsibility and safety for use of the wheelchair from the manufacturer that is performing the substitution or alteration. - Page 45 Measured from front of seat plate to backrest hinge without cushion. Using standard Netti Superstabil S backrest cushion subtract approximately 30 mm. Measured from seat plate to top of back rest Velcro. The weight is including main wheels, front castors, and arm supports.
- Page 46 Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05...
- Page 47 Model: NettI Dynamic S My-Netti.com Language: English Version: 2018-05...
- Page 48 To ConTaCT us: manufaCTurEr: disTribuTor: Alu Rehab AS Alu Rehab ApS Bedriftsvegen 23 Kløftehøj 8 4353 Klepp Stasjon DK-8680 Ry NORWAY T: +45 87 88 73 00 T: +47 51 78 62 20 F: +45 87 88 73 19 post@My-Netti.no info@My-Netti.com...
Need help?
Do you have a question about the DYNAMIC S and is the answer not in the manual?
Questions and answers