Gree GVC24AMXF-K3NTC7A Service Manual page 30

6. Function and Control
Service Manual
10. SLEEP button
Under COOL or HEAT mode, press this button to start up sleep
function. " " icon is displayed on remote controller. Press
this button again to cancel sleep function and "
disappear. After powered on, Sleep Off is defaulted. After the
unit is turned off, the Sleep function is canceled. In this mode,
set temperature will be adjusted with the change of time. Under
Fan, DRY and Auto modes, this function is not available.
11. WiFi button
Press "WiFi" button to turn on WiFi function, "WiFi" icon will be
displayed on the remote controller; Hold "WiFi" button for 5s to
turn off WiFi function and "WiFi" icon will disappear. Under off
status, press "MODE" and "WiFi" buttons simultaneously for 1s,
WiFi module will restore factory settings.
● This function is only available for some models.
12. X-FAN button
Pressing this button in COOL or DRY mode, the icon "
is displayed and the indoor fan will continue operation for a
few minutes in order to dry the indoor unit even though you
have turned off the unit. After energization, X-FAN OFF is
defaulted. X-FAN is not available in AUTO, FAN or HEAT mode.
This function indicates that moisture on evaporator of indoor unit
will be blowed after the unit is stopped to avoid mould.
● Having set X-FAN function on: After turning off the unit by
pressing ON/OFF button indoor fan will continue running for
about a few minutes. at low speed. In this period, press X-FAN
button to stop indoor fan directly.
● Having set X-FAN function off: After turning off the unit by
pressing ON/OFF button, the complete unit will be off directly.
● Only under cooling mode and dry mode, press this button
can turn on (characters of "X-FAN" are displayed) or turn off
(characters of "X-FAN" are not displayed) X-FAN function.
13. button
function is for limiting power of the whole unit. Press this
button, the controller will cercularly display as the following:
● Maximum power limited under the
mode.
● If you want to cancel the power limiting function, press the
button till the icon in remote controller is not displayed.
● When the remote controller is turned off, power limiting
function is cancelled. If you want to activate the function, please
repress this button.
● If the current power is lower than the maximum power of
mode, then the power will not be limited after entering into such
mode.
Technical Information
" icon will
"
blank
No Setting
mode is lower than that of
● For the model with one outdoor unit and two indoor units, if
any one of indoor units enters into power limiting function, the
outdoor unit will enter into the set limiting power mode of indoor
unit; when two indoor units enter into power limiting mode, then
the power of outdoor unit will be limited according to the lower
power of the two indoor units.
NOTE:
● This function is only available for some models.
14. LIGHT button
Press this button to turn off display light on indoor unit. Press
this button again to turn on display light.
15. TIMER button
● At ON status, press this button once can set TIMER OFF. The
character of HOUR and OFF will flash. Press "▲" or "▼" button
within 5s can adjust the time of TIMER ON. After each pressing
of "▲" or "▼" button time will increase or decrease half an hour.
When holding "▲" or "▼" button, 2s later, the time will change
quickly until to reach to your required time. After that, press
"TIMER" button to confirm it. The character of HOUR and OFF
won't flash again. Cancel TIMER OFF: Press "TIMER" button
again under TIMER OFF status.
● At OFF status, press this button once can set TIMER ON.
Please refer to TIMER off for detailed operation.
Cancel TIMER ON: Press "TIMER" button again under TIMER
ON status.
NOTE:
● Time setting range: 0.5-24 hours.
● Time inter val between two operations can't exceed 5s.
Other wise, remote controller will exit the set ting status
automatically.
Function introduction for combination buttons
Child lock function
Press "▲" and "▼" simultaneously to turn on or turn off child lock
function. When child lock function is on, "
on remote controller. If you operate the remote controller, the
" " icon will blink three times without sending signal to the unit.
Temperature display switchover function
U n d e r O F F s t a t u s , p r e s s "▼" a n d " M O D E " b u t t o n s
simultaneously to switch temperature display between °C and °F.
Replacement of batteries in remote controller
1. Lift the cover along the direction of arrow (as shown in Fig 1① ).
2. Take out the original batteries (as shown in Fig 1 ② ).
3. Place two 7# (AAA 1.5V) dry batteries, and make sure the
position of " + " polar and " - " polar is correct (as shown in Fig 2
③ ).
4. Reinstall the cover (as shown in Fig 2 ④ ).
" icon is displayed
27