Table of Contents
Advertisement
PLATINUM
Series User's Guide
TM
5.3.6
Alarm High High / Low Low Offset Value (PRoG > ALM.1, ALM.2 > HI.HI) ......................... 38
5.3.7
Alarm Latching (PRoG > ALM.1, ALM.2 > LtCH) .................................................................. 38
5.3.8
Alarm Normally Closed, Normally Open (PRoG > ALM.1, ALM.2 > CtCL) ........................... 39
5.3.9
5.3.10
Alarm On Delay (PRoG > ALM.1, ALM.2 > dE.oN) ............................................................... 39
5.3.11
Alarm Off Delay (PRoG > ALM.1, ALM.2 > dE.oF) ............................................................... 39
5.4
Output Channel 1-3 Configuration (PRoG > oUt.1-oUt.3) ......................................................... 40
5.4.1
Output Channel Mode (PRoG > oUt1-oUt3 > ModE) ......................................................... 40
5.4.2
Output Cycle Pulse Width (PRoG > oUt1-oUt3 > CyCL) ...................................................... 42
5.4.3
Analog Output Range (PRoG > oUt1-oUt3 > RNGE) ........................................................... 43
5.5
PID Configuration (PRoG > PId.S) ................................................................................................ 43
5.5.1
Action Response (PRoG > PId > ACtN) ................................................................................ 43
5.5.2
Autotune Timeout (PRoG > PId > A.to) ............................................................................... 44
5.5.3
Autotune (PRoG > PId > AUto) ............................................................................................ 44
5.5.4
PID Gain Settings (PRoG > PId > GAIN) ................................................................................ 44
5.5.5
Low Output Clamping Limit (PRoG > PId > %Lo) ................................................................. 45
5.5.6
High Output Clamping Limit (PRoG > PId > %HI) ................................................................ 45
5.5.7
Adaptive Tuning (PRoG > PId > AdPt) ................................................................................. 45
5.6
Remote Setpoint Configuration (PRoG > RM.SP) ........................................................................ 46
5.6.1
Cascade Control using Remote Setpoint ............................................................................. 47
5.7
Multi-Ramp/Soak Mode Parameters (PRoG > M.RMP) .............................................................. 48
5.7.1
Multi-Ramp/Soak Mode Control (PRoG > M.RMP > R.CtL) ................................................. 48
5.7.2
Select Program (PRoG > M.RMP > S.PRG) ........................................................................... 49
5.7.3
Multi-Ramp/Soak Tracking (PRoG > M.RMP > M.tRk) ........................................................ 49
5.7.4
Time Format (PRoG > M.RMP > tIM.F) ............................................................................... 49
5.7.5
Program End Action (PRoG > M.RMP > E.ACT) ................................................................... 49
5.7.6
Number of Segments (PRoG > M.RMP > N.SEG) ................................................................. 50
5.7.7
Segment Number for Editing (PRoG > M.RMP > S.SEG) ..................................................... 50
5.7.8
More on Multi-Ramp/Soak Programming .......................................................................... 51
6.
Reference Section: Operating Mode (oPER) ....................................................................................... 52
6.1
Normal Run Mode (oPER > RUN) ................................................................................................ 52
6.2
Change Setpoint 1 (oPER > SP1) .................................................................................................. 53
Introduction
Omega Engineering | www.omega.com
5
Advertisement
Table of Contents
