Related Manuals for YASKAWA 67S-RTP0-KB
Summary of Contents for YASKAWA 67S-RTP0-KB
- Page 1 PPC | 67S-RTP0-KB | Manual HB160 | PPC | 67S-RTP0-KB | en | 23-20 Panel PC - PPC021 IE...
- Page 2 YASKAWA Europe GmbH Philipp-Reis-Str. 6 65795 Hattersheim Germany Tel.: +49 6196 569-300 Fax: +49 6196 569-398 Email: info@yaskawa.eu Internet: www.yaskawa.eu.com 67S-RTP0-KB_000_PPC021IE,3,EN - © 2023...
-
Page 3: Table Of Contents
5.2.2 EMC-equitable assembly................65 5.2.3 EMC-equitable cabling................66 5.2.4 Special precautions providing high noise immunity........69 5.2.5 Checklist for the EMC-compliant installation of controllers......70 Appendix....................... 71 A History of changes.................... 73 HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 4: General
This material is protected by copyright laws. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to Yaskawa) except in accordance with applicable agreements, contracts or licensing, without the express written consent of Yaskawa and the business management owner of the material. -
Page 5: About This Manual
DANGER! This device is not certified for applications in – in explosive environments (EX-zone) HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 6 Installation and hardware modifications only by properly trained per- sonnel. – The national rules and regulations of the respective country must be satisfied (installation, safety, EMC ...) Disposal National rules and regulations apply to the disposal of the unit! HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 7: Hardware Description
Instruments must be grounded. Modifying electrostatic sensitive modules you should only use soldering irons with grounded tips. CAUTION! Personnel and instruments should be grounded when working on electro- static sensitive modules. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 8: Properties
Easy mounting via integrated pivoted lever Protection class IP66 (frontal) Order data Type Order number Description PPC021 IE 67S-RTP0-KB 21.5'' TFT color, 2x RS232/RS422/RS485, 3x USB-A, 2x Ethernet RJ45, VGA, Audio out HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 9: Structure
10 2 pin connector for remote Power switch 11 3.5mm Audio Line out 12 Power switch (pushbutton) 13 Slot for CFast storage media 14 Display with touch sensitive area (touch screen) HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 10 PC has to be switched off by the power switch. Loss’ page 51 Ò After a Windows ‘Shut down’ the Panel PC can be switched on again by means of the power switch at any time. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 11: Interfaces
The matching 3-pin plug con- nector is included in the scope of delivery. VGA interface VGA SubD HD15 jack to connect a second display. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 12 RS485 interface Logical conditions as voltage difference between 2 twisted lines Serial bus connection half-duplex two-wire operation Line length: 250m at 115.2kbit/s ... 1200m at 19.2kbit/s Data transfer rate up to 115.2kbit/s HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 13 Hardware description Structure > Interfaces HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 14 PPC on or off from any location. The matching 2-pin plug connector is included in the scope of delivery. Ä further information page 10 Line out 3.5 mm stereo jack to connect an active speaker system or an earphone. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 15: Memory Management
CFAST_CDI PC13 VCC3 PC14 VCC3 n.c. PC15 n.c. PC16 n.c. PC17 CFAST_CDO Prior to removing the CFast card, make sure the unit's power is off and disconnected from the power supply. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 16: Dimensions
The material thickness of the installation cut-out is 3 ... 12mm £ 0.5mm – The deviation from the plane for the panel cut-out is £ 120µm (fric- – Permissible surface roughness in the area of the seal: tion coefficient 120) HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 17: General Data
EN 61131-2 Degree of pollution 2 Mechanical Oscillation EN 60068-2-6 1g, 9Hz ... 150Hz Shock EN 60068-2-27 15g, 11ms Mounting conditions Mounting place In the control cabinet Mounting position Horizontal and vertical HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 18: Use In Difficult Operating Conditions
478 mm Display size (height) 269 mm Resolution 1080 x 1920 / 1920 x 1080 Aspect ratio 16:9 Type of display TFT color (16.7M colors) MTBF Backlights (25°C) 50000 h System properties HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 19 Sub-D, 9-pin, male Number of USB-A interfaces USB-A connector USB-A (host) Number of USB-B interfaces USB-B connector Number of ethernet interfaces Ethernet Ethernet 10/100/1000 MBit Ethernet connector 2 x RJ45 Integrated ethernet switch HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 20 12 mm Net weight 8.75 kg Weight including accessories 12.39 kg Gross weight 12.39 kg Environmental conditions Operating temperature -10 °C to 60 °C Storage temperature -20 °C to 75 °C HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 21 Hardware description Technical data > 67S-RTP0-KB Order no. 67S-RTP0-KB Certifications UL certification KC certification HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 22: Deployment Panel Pc
Push the Panel PC [3] from the front side into the front panel cutting [1] until it touches the panel with the seal [2]. Rotate the pivoted lever 90 degrees to the outside [4]. Screw the screws with the crosstip screwdriver [5]. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 23: Installation Of The Cfast Card
Push the CFast card to remove the card. Reinstall the cover plate. CAUTION! Prior to removing the CFast card, make sure the unit's power is off and disconnected from the power supply. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 24: Commissioning
After opening the control cabinet or desk, there are parts with pos- sible dangerous voltage available. – For all signal connections only screened cables are permitted. – Signal cables must not be let within the same cable shaft as high voltage cables. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 25: Startup-Manager
A delay time of 5 seconds is default. In the selection menu under [Autostart] you can adjust this time. Selection menu There are following buttons in the selection menu: Settings Info/Update Autostart Backup Exit Back HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 26 ‘Back è Exit’and right- click on the StartUp icon to select ‘StartUp è Run as administrator’. The StartUp icon can be found on the desktop, the taskbar and in the start menu. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 27 With [...] at ‘Runtime path’ res. ‘Project path’ all existing runtimes res. projects on the panel and the storage media will be listed. Under ‘Delay Time’ you can adjust a delay time > 0 by using the buttons [+] and [-]. 5 seconds are default. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 28 è VipaStartup’. These can be adjusted accordingly. Ò Exit The Startup-Manager will be closed by [Exit] and the system returns to the Windows screen. Back With [Back] you get back to the start screen of the Startup-Manager. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 29: Firmware Update
Internet. An active internet connection is required for this. If there is no update internet connection, the device remains in the "Referred activation state"; this does not result in any functional restrictions. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 30: Connection To A Plc System
During operation your operating device communicates with the according PLC and reacts to the application courses in the PLC according to the configured processes. Via dialogues configured before, process values may be monitored graphically, altered and evaluated. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 31: Operating System Windows 10 Iot Enterprise
Navigation within the The windows may be moved via the head bar. Here you may also find the [OK] button to dialog window confirm entries and the [X] button for exiting the dialog. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 32: Structure
Via this buttons you may easily change between the open windows. Task bar Basically the taskbar has the following structure: HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 33 è Change adapter settings’. By double-click on the network the dialog window for network properties opens. Here you can enter the Ethernet address via [Properties] after double-click on [Internet Protocol Version ..]. The default setting is address assignment via DHCP. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 34 Allow remote access By default, remote access to the Panel PC is disabled. For release, open the window ‘Remote desktop’ via ‘Windows Start è Settings è System’ and activate ‘Enable remote access’ . HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 35 Disable automatic log-in By default, the Panel PC automatically logs in with the user name Yaskawa and the pass- word vipatp. If the user needs to enter name and password to use the Panel PC, the pro- cedure is as follow: Type "control userpasswords2"...
- Page 36 In the opening dialog window uncheck the box ‘User must enter a user name and password to use this computer’ and choose the user which should be automatically logged in after booting. Confirm with [Apply]. The window for entering the login data opens. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 37 Operating system Windows 10 IoT Enterprise > Structure Enter the ‘Password’ for the selected user. Confirm with [OK] and in the next window again with [OK]. ð The next start-up takes place without requesting the log-in data. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 38: Bios Setup
Powering on the computer and immediately pressing [Del] allows you to enter Setup. Selection boot medium Powering on the computer and immediately pressing [F7] allows you, as long as the loading screen is shown, to change to the boot medium selection. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 39: Main
Security - Security settings Save and Exit - Save and exit 4.2 Main The Main menu is the first screen that you will see when you enter the BIOS setup utility. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 40: Advanced
This menu allows you to configure the system's extended functions. Here you can con- figure the CPU and the periphery. CAUTION! Setting incorrect field values may cause the system to malfunction. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 41 BIOS Setup Advanced Submenu "ACPI Settings" This section is used to configure Advanced Configuration and Power Interface (ACPI) Settings. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 42 - Sleep state disabled S3 (Suspend to RAM) - Standby mode enabled, Windows saves the system state in RAM. Submenu "IT8786E Super This section is used to configure serial ports. IO Configuration" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 43 BIOS Setup Advanced Super IO Chip Displays the Super I/O Chip used on the board. Submenu "Serial Port 1 This section is used to configure serial port 1. Configuration" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 44 Enables or disables the serial port. Disabled - Serial port is not available Enabled - (default) Serial port is available Device Settings Selects an optimal setting for the Super IO Device. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 45 Enabled - (default) Terminal resistor activated Submenu "H/W Monitor" This section ‘Pc Health Status’ is used to configure the hardware temperature and vol- tages. Submenu "CPU Configura- This section is used to configure the CPU. tion" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 46 XD feature flag to always return to 0. Enables or disables Intel Virtualization Technology. Intel ® Virtualization Tech- nology Submenu "Socket 0 CPU Display information on the CPU installed on socket 0. Information" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 47 BIOS Setup Advanced Submenu "PPM Configu- This section is used to configure the Processor Power Management (PPM) configuration. ration" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 48 Enables or disables Hot Pluggable Support on SATA port 0. Serial-ATA Port 1 Enables or disables SATA port 1. SATA Port1 HotPlug Enables or disables Hot Pluggable Support on SATA port 1. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 49 Disabled - Disables XHCI (USB 3.0) or EHCI (USB 2.0) support. When installing Windows 7 from USB, USB 3.0 will not be supported. Please disable XHCI and enable EHCI to allow USB installation of Win- dows 7. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 50: Chipset
‘Manual’ and the Backlight option below will be configurable. Backlight Dimming Select Adjust the brightness of the backlight. Submenu "South Bridge" This field is used to configure the South Bridge chipset. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 51 Power Off - The system’s power is off. You must press the power button to Power On the system. Power On - (default) The system will automatically Power On. Submenu "Azalia HD This section disables Azalia or enables HD Audio. Audio" HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 52 Control detection of the Azalia device. Disabled - Azalia will be unconditionally disabled. Enabled - Azalia will be unconditionally enabled. Azalia HDMI Codec Enables or disables internal HDMI Codec for Azalia. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 53 Enables or disables the Enhanced Host Controller Interface (USB 2.0), one EHCI con- troller must always be enabled. USB RMH Mode Enables or disables PCH USB rate matching hubs mode. USB EHCI debug Enables or disables PCH EHCI debug capability. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 54 BIOS Setup Chipset Submenu "PCI Express Configuration" PCI Express Port 0 ... PCI Enables or disables the PCI Express ports 0 ... 3 on the chipset. Express Port 3 HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 55: Boot
Enabled - Starts the LAN PXE ROM, to be able to boot about PXE Boot Option Priorities Adjust the boot sequence of the system. Hard Drive BBS Priorities Sets the order of the legacy devices in this group. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 56: Security
If only the User's password is set, then this is a power on password and must be entered word is set to boot or enter setup. In Setup the user will have administrator rights. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 57 3 characters and should be maximal 20 characters long. User Password Select this to reconfigure the user’s password. Your password must contain at least 3 characters and should be maximal 20 characters long. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 58: Save And Exit
To save the changes and exit the setup utility press [F4]. Discard Changes and Exit To exit the Setup utility without saving the changes [Esc]. The BIOS setup exits and the POST continued. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 59: Industrial Security And Installation Guidelines
You can find more information about the measures on the following websites: Federal Office for Information Technology www.bsi.bund.de Cybersecurity & Infrastructure Security Agency us-cert.cisa.gov VDI / VDE Society for Measurement and Automation Technology www.vdi.de HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 60: Protection Of Hardware And Applications
Use secure access paths such as HTTPS or VPN for remote access to your plant. Enable security-related event logging in accordance with the applicable security policy and legal requirements for data protection. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 61: Protection Of Pc-Based Software
The components are developed for the deployment in industrial environments and meets high demands on the EMC. Nevertheless you should project an EMC planning before installing the components and take conceivable interference causes into account. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 62 Capacitate or electric coupling occurs Interference through parallel signal between conductors with different lines potential. The coupling is propor- Static discharge of the personnel tionate to the temporal change of the Contactors voltage. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 63 – Make sure that the isolation/protected earth conductor rail is connected impe- dance-low with the cabinet. – Use metallic or metallised plug cases for isolated data lines. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
- Page 64 Connect installation parts and cabinets with your PLC in star topology with the isolation/protected earth conductor system. So you avoid ground loops. – If there are potential differences between installation parts and cabinets, lay suffi- ciently dimensioned potential compensation lines. HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 65: Emc-Equitable Assembly
Moveable grounding parts (e.g. cubicle doors) have to be connected via flexible ground strips. The ground strips should be short and have a large surface, because the surface is decisive for the diversion of high frequency interferences. HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 66: Emc-Equitable Cabling
Wherever possible, exterior cabling should be installed on metallic cable trays. A galvanic buildings connection must be provided for joints between cable trays. You must abide by the appli- cable lightning protection and grounding regulations when installing exterior cables. HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 67 Install these protective elements at the location where the cables enter the building. Any lightning protection system must be based on an individual assess- ment of the entire plant. For questions please contact Yaskawa. Equipotential bonding Potential differences can occur between different sections when controllers and periph-...
- Page 68 Attach the screens to the screening rail directly at the point where the cables enter the enclosure. The screening conductor must be continued to the module without interruption, however, it must not be connected to the module! HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 69: Special Precautions Providing High Noise Immunity
Suppression of fluores- cent lamps in cubicles Fluorescent lamp Screen above the lamp Screened cable Switch with metallic cover Line filter or screened power cable HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 70: Checklist For The Emc-Compliant Installation Of Controllers
Have the screens been connected by means of large-surface and low-impedance cable clamps? Cable screens grounded both-sided where possible? Inductors Have the coils of contactors controlled by means of contacts been connected to snubber networks? HB160 | PPC | 67S-RTP0-KB | en | 23-20... -
Page 71: Appendix
Appendix Appendix HB160 | PPC | 67S-RTP0-KB | en | 23-20... - Page 72 Appendix Content History of changes.................... 73 HB160 | PPC | 67S-RTP0-KB | en | 23-20...
-
Page 73: A History Of Changes
Rev. Changes 22-04 The manual was created. 22-22 CI adjustment was done. Chapter "Hardware description" Description "Use in difficult operating conditions" was added. 23-20 Chapter "Hardware description" "Technical Data" was updated. HB160 | PPC | 67S-RTP0-KB | en | 23-20...