Assa Abloy Sargent 855 Installation And Wiring Instructions
Assa Abloy Sargent 855 Installation And Wiring Instructions

Assa Abloy Sargent 855 Installation And Wiring Instructions

Signal switch kit with electrolynx connector system

Advertisement

Installation and Wiring Instructions
855 Signal Switch Kit
with ElectroLynx
Connector System
®
The 855 Signal Switch Kit is designed to be
retrofit into an existing 80 Series rail assembly.
The signal switch monitors the touch bar and
signals a remote location that someone has
egressed. The 855 signal switch can also be
used as a request to exit switch, to de-energize
a mortise lock.

A. Preliminary Preparation:

1. Provide a 1/4" diameter minimum
raceway in the door to allow insertion of
electrical wires running between signal
switch and electric hinge.
2. Wiring instructions - see wiring diagram
for necessary information.

B. Installation Procedure:

1. Remove end cap by taking out two (2)
screws securing it.
2. Remove mounting plate by taking out
two (2) screws securing it.
3. Remove two (2) #8-32 truss head screws
holding rail to chassis.
4. Remove rail from door.
5. Slide mounting insert out of rail.
6. Loosen two (2) #6-32 flat head screws
on back of rail (closer to hinge).
7. Lift connecting arm bracket and slip
855 switch assembly under bracket, as
shown.
8. Install switch leaf under tail of connecting
arm. Important: Switch leaf may break if
installed on top.
9. Ensure connecting arm bracket is sitting
flush against rail mount.
10. Tighten #6-32 screws.
11. Slide mounting insert back into rail.
12. Install rail onto chassis and tighten #8-32
truss head screws.
13. Reinstall mounting plate and end cap
with appropriate screws.

C. Installation Notes:

1. Door without ElectroLynx connector
system: Cut 8-pin connector off signal
switch wires and hardware to electric
hinge as required.
2. Wiring to pigtail harness or electric hinge
is per facility wiring requirement.
1-800-727-5477 • www.sargentlock.com
Copyright © 2018, 2019, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov.
Steps B1 and B2
Loosen
#6-32 Flat Head Screws
(DO NOT REMOVE)
Steps B5 and B6
Connecting
Arm
Connecting
Arm Bracket
Steps B7 and B8
Step B3
Mounting
Insert
Switch
855 Switch
Leaf
Assembly
A7110D 04/19

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sargent 855 and is the answer not in the manual?

Questions and answers

Summary of Contents for Assa Abloy Sargent 855

  • Page 1 1-800-727-5477 • www.sargentlock.com A7110D 04/19 Copyright © 2018, 2019, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
  • Page 2 New Haven, CT 06511 USA 800-727-5477 www.sargentlock.com Copyright © 2018, 2019, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Patent pending and/or patent: www.assaabloydss.com/patents...

Table of Contents