Items For Which User Settings Are Available - Pioneer DDJ-SR Service Manual

5

8.3 ITEMS FOR WHICH USER SETTINGS ARE AVAILABLE

This unit is provided with user settable items, as shown below.
Although no serious operational problems occur even if data for such user settable items are cleared during repair, it is
recommended that you take note of those settings before starting repair.
Use the Check Sheet shown next page, to which you can transcribe the settings.
If the corresponding part or board Assy is replaced for repair, change the user resettable settings to those noted on the Check
Sheet before starting repair. If resetting is not possible, when returning the repaired product, be sure to tell the customer that
the Utility settings have been cleared and will have to be reset, as required.
Item for Which User's
Setting is Available
Settings for DJ software
other than Serato DJ
Channel fader start setting
Master output' s attenuation
level setting
Slip mode flashing setting
Demo mode setting
Sampler velocity Velocity curve setting
mode setting
After touch setting
Jog dial MIDI message sending interval
setting
Default value of the beat for
the hot cue roll function setting
FX level Default value of the
Combo FX level setting
Default value of the Combo FX
filter operation mode setting
Default value of the beat for
the sampler roll function setting
Momentary mode setting
Pad Plus mode flashing operation
setting
Each of the above items can be set in Utility mode.
To enter Utilities mode 1, terminate the application, turn the unit OFF, then while holding the [SHIFT] and
[PLAY/PAUSE] buttons on the left deck pressed, set the [ON/OFF] switch on the rear panel of the unit to ON.
To enter Utilities mode 2, terminate the application, turn the unit OFF, then while holding the [SHIFT] and
[PLAY/PAUSE] buttons on the right deck pressed, set the [ON/OFF] switch on the rear panel of the unit to ON.
(For details, refer to the operating instructions of the unit.)
5
6
Setting Value (The factory default
settings are indicated in bold.) / Indication method
Setting to use Serato DJ • Setting to use DJ software other than Serato DJ
Left Deck [KEY LOCK] button unlit • [KEY LOCK] button lit
With SYNC, without SYNC, function disabled
Left Deck Effect parameter 1 button lit • Effect parameter 2 button lit •
Effect parameter 3 button lit
0 dB (no attenuation) • −3 dB • −6 dB
Left Deck [HOT CUE] mode button lit • [ROLL] mode button lit •
[SLICER] mode button lit
Settings enabled • Settings disabled
Left Deck [SLIP] button lit • [SLIP] button unlit
Demo mode enabled • Demo mode disabled
Left Deck [TAP (FX MODE)] button lit • [TAP (FX MODE)] button unlit
Curve 1 • Curve 2 • Curve 3 • Curve 4
[1/2X (IN)] button lit • [2X (OUT)] button lit •
[PARAMETER <] button lit • [PARAMETER >] button lit
Settings enabled • Settings disabled
[SAMPLER] mode button lit • [SAMPLER] mode button unlit
3 ms • 4 ms • 5 ms • 6 ms • 7 ms • 8 ms • 9 ms •
10 ms • 11 ms • 12 ms • 13 ms
Level indicator lighting LED number:
0 • 1 • 2 • 3 • 4 • 5 • 6 • 7 • 8 • 9 • 10
1/32 • 1/16 • 1/8 • 1/4 • 1/2 • 1
Left Deck Beat indicator indication: 1/32 • 1/16 • 1/8 • 1/4 • 1/2 • 1
Level 12 • Level 50 • Level 75 • Level 100
When the HOT CUE button on the left deck is pressed, a value is
indicated with the Beat indicator on the left deck.
Right Deck Level indicator lighting LED number: 1 • 2 • 3 • 4
Off • Slow • Quick • LFO
When a Performance pad is pressed after the HOT CUE button on
the right deck is pressed, a value (1, 2, 3, or 4) will be indicated with
the left-column LEDs of the LEVEL indicator.
A default value can be set separately for each of the 6 Performance
pads (1, 2, 3, 5, 6, or 7).
Level indicator lighting LED number: 1 • 2 • 3 • 4
1/32 • 1/16 • 1/8 • 1/4 • 1/2 • 1
When a Performance pad is pressed after the ROLL button on the
right deck is pressed, a value (1, 2, 3, or 4) will be indicated with the
right-column LEDs of the LEVEL indicator.
A default value can be set separately for each of the 6 Performance
pads (1, 2, 3, 5, 6, or 7).
Left Deck Beat indicator indication: 1/32 • 1/16 • 1/8 • 1/4 • 1/2 • 1
When the SAMPLER button on the left deck is pressed, a value is
indicated with the Beat indicator on the left deck
Settings enabled • Settings disabled
Left Deck [PAD PLUS ON]button lit • [PAD PLUS ON] button unlit
Settings enabled • Settings disabled
Left Deck [PAD PLUS TAP] button lit • [PAD PLUS TAP] button unlit
DDJ-SR
6
7
Part Name
IC19
(I/O PCB Assy)
7
8
A
Content to
be Stored
B
C
UTILITY
setting
D
E
F
35
8