Subscribe to Our Youtube Channel
Related Manuals for Perlick PTR Series
Summary of Contents for Perlick PTR Series
- Page 1 Installation & Operation Manual Commercial Back Bar Pass Thru PTR & PTS Series Model PTS36 Shown Form No. 2622013 Rev. 04.18.2017...
-
Page 2: Table Of Contents
For your own protection, never return Serial Number: _________________________ merchandise for credit without our approval. Purchase Date: _______________________ We thank you for selecting a Perlick product Dealer Name & Address and assure you of our continuing interest in your ______________________________________ satisfaction. -
Page 3: Prior To Installation
“Condensate Evapaway’ pan and heater. cabinet for hidden damage. If damage is discovered, file your claim immediately with the Electrical transport company. Perlick is not responsible for The cabinet must be connected to a separately damage in transit. fused power source (see Electrical Specification... -
Page 4: Installation
Models PTR/PTS Installation & Operation Manual INSTALLATION General Information Installing the Unit If unit has been laid on its • For units equipped with a power cord, the CAUTION cord and plug may be aligned with a recess in back or sides, place unit the back panel to allow the unit to be pushed upright and allow minimum of 24 hours before closer to the wall. -
Page 5: Operation
Models PTR/PTS Installation & Operation Manual Sealing Cabinet to Floor Cabinet For units without casters or legs, it may be necessary to seal the base of the cabinet to Bead Silicon the floor. This can be accomplished by laying a Sealer (RTV) bead of silicone sealant between the base of the cabinet and the floor (Figure 1). -
Page 6: Adjustments
Tools Required step 3. • Large flat head screwdriver • Regular Phillips head screwdriver • Hinge Kit from Perlick • Plastic putty knife Procedure SUPPORT Pull door to the side then lower door Figure 4. Hinge Removal Remove hinge pin Figure 3. - Page 7 Models PTR/PTS Installation & Operation Manual 5. Using the screws removed in step 3, install Front panel the top and bottom hinge brackets from kit (Figure 5). Hinge brackets and mounting screws Hinge brackets and mounting Corner screws need not be screws removed to remove front panel Figure 5.
- Page 8 Models PTR/PTS Installation & Operation Manual 10. Attach the top and bottom door hinges using screws removed in step 6 (Figure 9). 11. Place lower V-block into lower cabinet hinge with notch parallel to cabinet (Figure 10). Figure 9. Door Hinges Figure 11.
-
Page 9: Maintenance
Models PTR/PTS Installation & Operation Manual MAINTENANCE Never attempt to repair or the metal is passive and stainless. If the passive DANGER perform maintenance on film of stainless steel has been broken, equipment the unit until the main electrical power to the starts to corrode and rust. - Page 10 Models PTR/PTS Installation & Operation Manual Keep food equipment clean. Use alkaline Glass panels may be cleaned using any standard chlorinated or non-chloride cleaners at glass cleaner available on the market. recommended strength. Clean frequently to avoid To clean interior and exterior non-metallic surfaces build-up of hard, stubborn stains.
- Page 11 Models PTR/PTS Installation & Operation Manual Recommended Cleaners for Specific Situations Cleaning Agent Comments Routine cleaning. Soap, ammonia, detergent Apply with sponge or soft cloth. Fingerprints and smears. Areal 20, Lac-O-Nu, Lumin Wash, Provides barrier film to minimize finger- O’Ceder Cream Polish prints.
-
Page 12: Troubleshooting
Models PTR/PTS Installation & Operation Manual TROUBLESHOOTING Before Calling For Service If the unit appears to be malfunctioning, read through the Operation section in this manual first. If the problem persists, check through this troubleshooting section. Locate the problem and refer to the cause and remedy before calling for service. - Page 13 Use only genuine Perlick replacement parts and accessories. Genuine Perlick parts and accessories are designed to work correctly with Perlick products and offer superior service life. The use of non- Perlick parts can damage the unit and may void the warranty.
-
Page 14: Dimensions
Models PTR/PTS Installation & Operation Manual DIMENSIONS Printed in USA 0213... - Page 15 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
-
Page 16: Wiring Diagrams
Models PTR/PTS Installation & Operation Manual WIRING DIAGRAMS Printed in USA 0213... - Page 17 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
- Page 18 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
- Page 19 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
- Page 20 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
-
Page 21: Warranty
IF ANY ITEMS ARE statement of their agreement. Any changes to an SHORT OR DAMAGED, DO NOT ACCEPT THE Order must be in writing and signed by Perlick SHIPMENT UNLESS THE CARRIER MAKES A and Buyer. NOTATION OF THIS ON YOUR FREIGHT BILL. - Page 22 $35.00, whichever is Perlick’s one year labor warranty provides greater. that Perlick will pay for the cost of any labor to replace any defective part for up to one year ONE YEAR PARTS WARRANTY...
- Page 23 Models PTR/PTS Installation & Operation Manual Printed in USA 0213...
- Page 24 8300 West Good Hope Road • Milwaukee, WI 53223 • Toll Free 800.558.5592 • Fax 414.353.7069 • www.perlick.com...
Need help?
Do you have a question about the PTR Series and is the answer not in the manual?
Questions and answers