Related Manuals for Omega FPR310 Series
Summary of Contents for Omega FPR310 Series
- Page 1 User’s Guide FPR300 Shop online at omega.com e-mail: info omega.com For latest product manuals: www.omegamanual.info FPR310 FPR300/310 SERIES Low-Flow Meter...
- Page 2 Fax: (203) 359-7700 e-mail: info@omega.com For Other Locations Visit omega.com/worldwide The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
-
Page 3: Table Of Contents
Piping Requirements ..............................Page 6 K-Factor ...................................Page 6 Connections to Control Devices ..........................Page 6 Repair Rotor Replacement ..............................Page 7 Sensor Replacement ..............................Page 7 FPR300/310 Parts List ..............................Page 8 Troubleshooting Problem ...................................Page 9 Probably Causes ................................Page 9 Things to Try ..................................Page 9 Page 3 omega.com... -
Page 4: General Information
The pulse output of these meters is compatible with many The FPR300, with a body of polypropylene, is an economical different types of controls, including a full range of Omega choice for metering water or low corrosion fluids. The lens rate displays and controls. -
Page 5: Specifications
6–36 Vdc, 2 mA min. 6–36 Vdc, 2 mA min. Outputs Current sinking pulse, 6–24 Vdc Current sinking pulse, 6–24 Vdc * Specifications subject to change. Please consult our website for current data (omega.com) Dimensions 4.10 2.25 (FPR310)* 2.10 (FPR300) -
Page 6: Installation & Connections
FPR300/310 Series flow sensor with some form of 4-20 mA transmitter. Two options are the FMG-1000-MAW blind transmitter and the DPF144 indicating transmitter. Follow the connection diagrams for these products to connect to the analog input. Page 6 omega.com... -
Page 7: Repair
Check that the O-ring is in its seat on the bearing plate Reconnect the sensor according to the diagram below. before replacing the cover. Replace the cover, insert the four cap screws and tighten. (BLACK) Power (-) (WHITE) Signal (RED) Power (+) 6-24 Vdc SES SENSOR CONNECTION Page 7 omega.com... -
Page 8: Fpr300/310 Parts List
Not available Acrylic 100848 Not available PTFE Not available 100847 Cover Screws (4 required) Hexscrew 100310 Not applicable Screw (requires hex nut 100025) Not applicable 100022 Hex nut (requires screw 100022) Not applicable 100025 Sensor 100419 100419 Page 8 omega.com... -
Page 9: Troubleshooting
DPF143/144, set K to 1.00, turn rotor slowly by hand, indicator should count each blade; replace sensor Wrong time units on flow If using DPF143/144, check left side of display (sec, indicator min, hr, day); change to desired unit Page 9 omega.com... - Page 10 FPR300/310 SERIES INSTRUCTIONS Page 10 omega.com...
- Page 11 Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification.
- Page 12 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE M U Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies M U Wire: Thermocouple, RTD & Thermistor M U Calibrators & Ice Point References M U Recorders, Controllers &...