Related Manuals for Nice DC12-IP
Summary of Contents for Nice DC12-IP
- Page 1 DC12-IP IP Controlled, BlueBOLT Enabled DC Power Manager with 12 Outputs User Guide English...
-
Page 2: Table Of Contents
DC12-IP User Guide Table of Contents Important Safety Instructions ............3 FCC Notice. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. WARNING: Do not use this apparatus near water. To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. 6. -
Page 4: Dc Power Management With Control System Interactive Functionality
IMPORTANT: You will need the DC12-IP’s unique MAC Address and Challenge Key (provided on the labels attached to the cover of the instructions or bottom of the DC12-IP) to claim the DC12-IP on the BlueBOLT cloud control service. One label is permanently adhered to the device instructions and the other is removable for your convenience. -
Page 5: Included In The Box
INCLUDED IN THE BOX One (1) DC12-IP Detachable power cord (1 meter). Two (2) rack mount ears for attachment to DC12-IP. Four (4) Phillips pan head screws with at washers for rack mounting. Twelve (12) Plug-in Terminal blocks for DC outputs... -
Page 6: Front Panel Features Overview
DC12-IP User Guide FRONT PANEL FEATURES OVERVIEW 1. ON Button and Indicator Light Pressing the ON button initiates a power on sequence. During the power on sequence, DC outputs will switch on after the programmed turn on delay time. The ON indicator light will ash during the power on sequence to indicate that a power on sequence is in progress. After the power on sequence is complete, the ON indicator light will remain illuminated. - Page 7 • Should the total DC load exceed 110% of total capacity (165W), the DC OVERLOAD indicator will ash red and DC12-IP will automatically switch DC outputs off. In this state, the DC outputs will switch off from lowest priority (output 12) to highest priority (output 1) until the total DC load is 150W or less.
-
Page 8: Rear Panel Features Overview
DC12-IP User Guide REAR PANEL FEATURES OVERVIEW 1. AC Inlet: 100-240 V~ IEC-320 C14 Inlet 2. DC Output Banks 1-12 Each DC Output Bank is comprised of: • Plug in terminal block connector » Pin 1: +12VDC » Pin 2: +5VDC »... -
Page 9: Installation
INSTALLATION Install the provided rack mounting brackets to the sides of DC12-IP with the provided screws. Adjust the distance of the rack ears to the front panel for the desired position and tighten the screws. Install the DC12-IP into the equipment rack. -
Page 10: Wiring To Dc Output Terminals
When using the USB-A connector: 6. Connect the USB cable provided to the device and then to the USB connector on the DC12-IP rear panel. 7. Switch the DC output port on, and then observe the overload indicator light to ensure that the output port or system is not overloaded. -
Page 11: Bluebolt Setup
Local web page DC12-IP provides a built-in HTTP (web page server at default port 80) which can be accessed via a typical web browser. This allows the user to operate the device locally and con gure its settings. The web page is accessed by entering the device’s IP address into the web browser. The IP address can be discovered by lookup on the network router’s device table or from BlueBOLT. - Page 12 DC12-IP User Guide Information Panel » Serial Number: » MAC Address: » Firmware Version (Main) » Bootcode Version » Model: DC12-IP Status Panel » Wattage » Power Supply Protection » Power Supply Overload Controls Panel » Sequence Off » Sequence On »...
- Page 13 Con gure Panel - Network » Password Protection Enabled (Username, Password, Con rm) • Update Login (click to update new login information) » DHCP » Static » Update IP Address (click to update IP Address) Con gure Panel - Attached Device Settings »...
-
Page 14: Power Cycle And Output Sequencing
POWER CYCLE AND OUTPUT SEQUENCING The DC outputs of DC12-IP are con gured to turn ON and OFF in a programmed sequence where each output has a set of programmed delay times. The delay times are pre-programmed, but they may be changed on the BlueBOLT or local web site interface. The default con guration is:... -
Page 15: Troubleshooting
All equipment being returned for repair must have a Return Authorization (RA) number. To get an RA number, please call Nice Tech Support. Before returning any equipment for repair, please be sure that it is adequately packed and cushioned against damage in shipment, and that it is insured. -
Page 16: Warranty Information
(3) years (terms will vary depending on product) from the date of purchase. It is not transferable. If a defect exists, NICE NORTH AMERICA will have you ship the defective part or product to us and we will, at our option, either repair or replace it. This warranty does not cover the cost of labor to remove a defective part or product or to reinstall any repaired or replacement part or product.