Noise Reduction; Multi Space Mode; Self Cleaning Mode; Movement Sensor - Bosch Climate Class 6000i Operation Manual

The 1-2-3-5h off timer has priority over the off/on timer. If the 1-2-3-5h
off timer is set while the unit is not operating, the unit will start operating
and stop after the set period of time.
Set off timer
▶ Press the button.
The off timer indicator will blink.
▶ Press the . or / button to set the desired time.
(The time can be set in 10-minute increments or decrements.)
▶ Press the Set/C button.
The orange timer lamp on the unit will light up.
When the off timer is set, the temperature setting is automatically
adjusted to prevent the room from becoming excessively warm or cool,
for example while you sleep (auto sleep function).
In cooling or drying mode:
• One hour after the time operation begins, the temperature setting
rises 1 °C higher than the original temperature setting.
In heating mode:
• One hour after the timer operation begins, the temperature setting
drops 3 °C lower than the original temperature setting.
Set on timer
▶ Press the button.
The on timer indicator will blink.
▶ Press the . or / button to set the desired time.
(The time can be set in 10-minute increments or decrements.)
▶ Press the Set/C button.
The orange timer lamp on the unit will light up.
The unit will turn on prior to the set time. This allows the room to reach
the desired temperature by the programmed time (awaking function).
Cancel all timers
▶ Press the Set/C button.
The orange timer lamp on the unit will turn off.
The current clock time will be displayed on the remote control.
Combine on timer and off timer
On timer and off timer can be set at the same time. Either timer can be
programmed to activate prior to the other
▶ Set the on timer and off timer.
The settings will be automatically combined.
Example:
• Current time: 21:00
• Off timer at 11:00 p.m.
• On timer at 7:00 a.m.
An arrow ( or ) next to the timer indicator shows which timer will
activate first.
You can not program the on timer and off timer to operate the unit at
different temperatures or other settings.

3.11.3 Noise reduction

This function reduces the noises emitted by the outdoor unit when it is in
operation. This is particularly advantageous at night, if you need to show
consideration for your neighbours.
▶ During operation, press the
Climate Class 6000i/8000i – 6721831490 (2020/11)
button.
Exiting the function:
▶ Press the button again.
When noise reduction is active, a number of operating modes may not
reach their full performance potential. The sound pressure level is not
reduced if it has already dropped low enough at stable condition.

3.11.4 Multi space mode

Multi space mode cannot be activated during auto mode, the button is
disabled.
The unit will operate to cool or warm multiple rooms in a well insulated
house by pressing this button.
▶ During cooling or heating operation, press the
– In heating mode, the remote control displays
– In cooling mode, the remote control displays
The louver angle changes to the position for long distance delivery of
air. The remote control displays
To cancel multi space mode:
▶ Press the button again.
The unit will operate at extra high fan speed for long distance delivery of
conditioned air. After 15 minutes the unit shifts to high fan speed.
The Fan button is disabled during this operation mode.
Effectiveness of this function may differ depending on the room layout,
installation position of the unit, and insulation level of the space
concerned.

3.11.5 Self cleaning mode

Self cleaning mode will reduce the growth of mold fungus with
plasmacluster ions and dry the inside of the unit. Utilize this mode at
seasonal change over terms.
▶ Press the Clean button when the unit is not operating.
The remote control displays
The blue plasmacluster lamp on the unit turns on.
The unit stops operation after 90 minutes.
To cancel self cleaning mode:
▶ Press the Stop button.
The blue plasmacluster lamp on the unit turns off.
Temperature, fan speed, airflow direction or timer can not be set during
self cleaning mode.
Mold fungus already grown can not be eliminated by this operation.

3.11.6 Movement sensor

The movement sensor ( Fig. 1, [6]) is active in automatic mode. The
indoor unit is intelligently controlled, depending on the presence or
absence of persons and the amount of movement in the room.
• Function with low activity: if the sensor detects no movement in the
room for 60 minutes, the air conditioning system switches over to
Operation
button.
.
.
and .
for 1 minute.
17