System Menu - ADJ 3 SIXTY 2R User Instructions

3 Sixty 2R
Dmx Address
Dmx Value
Slave Mode
Auto Program
Sound Control
Time Information Current Time
Total Run Time
Last Run Time
Lamp Hours
Lamp Off Time
LastRun Password
Clean Last Run
LampTime Password
Clean Lamp Time
Temperature Info Head Temperature
Software Version V1.0.0......
Lamp On/Off
Automatic On
Lamp On via DMX
Lamp Off via DMX
Max On at Temp.
Lamp Off Temp.
Status Settings Address Via DMX
No DMX Status
Pan Reverse
Tilt_L Reverse
Tilt_R Reverse
Pan Degree
Feedback
Movement Speed
Mic Sensitivity
Hibernation
Service Setting Password
RDM PID
Shutoff Time
Display Setting
Display Reverse
Key Lock
Temperature C/F Celsius
Fahrenheit
Initial Status PAN =XXX
.......
Reset Default ON/OFF
Reset All
Reset Pan&Tilt
Reset Colors
Reset Gobos
Reset Shutter
Reset Others
Test Channel PAN ......
Manual Control PAN =XXX
:
Calibration Calibrate Password
Color wheel=XXX
:
User Mode Standard Mode
Basic Mode
Extended Mode
User Mode A
User Mode B
User Mode C
Edit User Mode Max Channel = XX
A/B/C PAN = CH01
:
Select Programs Auto Pro Part 1 = Program 1 ~ 10 Program 1
Auto Pro Part 2 = Program 1 ~ 10 Program 2
Auto Pro Part 3 = Program 1 ~ 10 Program 3
Edit Program Program 1
:
Program 10
Edit Scenes Edit Scene 001
~ Edit
250
Rec. Controller XX~XX
ADJ Products, LLC - www.adj.com - 3 Sixty 2R Instruction Manual Page 16

System Menu

A001~AXXX DMX address setting
PAN...... DMX value display
Slave1,Slave2,Slave3 Slave setting
Master / Alone Auto program
Master / Alone Music control
XXXX(Hours) Power on running time
XXXX(Hours) Fixture running time
XXXX(Hours) Fixture Last times clear
XXXX(Hours) Lamp running time
XXXX(Minute) Lamp off time
Password=XXX Timer Password 038
ON/OFF Clear Fixture Last time
Password=XXX Lamp Password ="038"
ON/OFF Clear lamp time
XXX / Temperature in the head
Software version
ON/OFF Lamp on/off
ON/OFF Lamp on/off Power on
ON/OFF Lamp on via DMX
ON/OFF Lamp off via DMX
20~79 ,45 /68~174 113 Lamp restart at temp.
80 ~ 139 , 130 /176~282 , 266 Lamp off at temp.
ON/OFF Add. via DMX
Close/Hold/Auto/Music Auto run if no DMX
ON/OFF Pan Reverse movement
ON/OFF Tilt_L Reverse
ON/OFF Tilt_R Reverse
540/630 Pan Degree Select
ON/OFF Movement Feedback
Speed 1~ 4 Movement Mode Select
0~99% Sensitivity of Mic.
OFF, 01M~99M 15M
Stand by Mode
Password=XXX Service Password"=050"
XXXXXX RDM PID Code
02~60m 05m
Display shutoff time
ON/OFF
Reverse 180 degree
ON/OFF Key Lock
Temperature switch
between /
Initial effect position
Restore factory set.
Reset all motors
Reset Pan/Tilt
Reset color wheel
Reset gobos
Reset shutter or dimmer
Reset other motors
Test function
Fine adjustment of the
lamp
Password "050"
Calbrate and adjust the
effects to standard/right
position
User's mode to change
channel numbers
Preset User modes
Select programs to be
run
Program Test Testing program
Step 01=SCxxx Program in loop
Step 64=SCxxx Save and exit
Pan,Tilt,......
Save and automatically
Scene --Fade Time--
return
--Secne Time--
manual scenes edit
Input By Exterior
Automat. scenes rec
3 Sixty 2R
The main menu is accessed by pressing the MODE/ESC button.
Browse through the menu by using the UP, DOWN, RIGHT, & LEFT
buttons. Press the ENTER button to access the desired menu. You
can scroll through the submenus using the UP, DOWN, RIGHT, &
LEFT buttons. To confirm every selection press the ENTER button.
You can exit every menu and submenu by pressing the MODE/ESC
button. The unit will automatically exit the menus if no buttons are
pressed after 10 seconds. These next pages will explain each func-
tion in the menu layout located on the previous page.
FUNCTION -
DMX Address - With this function, you can adjust the desired DMX-
address via the Control Board.
1. Access the main menu, and press the UP or DOWN buttons so
that "Function" is higlighted, then press ENTER.
2. Press the UP or DOWN buttons until "DMX Address" is displayed,
and press ENTER. The current DMX address will now be displayed.
3. Use the UP or DOWN buttons to adjust the DMX address.
4. Press ENTER to confirm or press MODE/ESC to return to the main
menu.
DMX Value - This function will allow you to see the DMX value of
each DMX channel that is currently being used at the time.
1. Access the main menu, and press the UP or DOWN buttons so
that "Function" is highlighted, then press ENTER.
2. Press the UP or DOWN buttons until "DMX Value" is displayed,
and press ENTER.
3. A DMX Channel will be displayed. Example: Prism, Color Wheel,
Gobo Wheel, etc... Press ENTER when you find the DMX channel that
you would like to check. When you press ENTER the DMX value of
that channel will displayed.
4. Press the MODE/ESC button to exit.
Slave Mode - This function lets you designate the unit as the slave in
a Master-Slave configuration.
ADJ Products, LLC - www.adj.com - 3 Sixty 2R Instruction Manual Page 17
System Menu