Table of Contents
Advertisement
The following signal words are used in this manual.
Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or
WARNING
may result in serious injury or death. Additionally there may be significant property damage.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or
CAUTION
in property damage.
The following alert symbols are used in this manual.
Indicates general prohibitions for which there is no
specific symbol.
Indicates the possibility of explosion under specific
conditions.
Indicates the possibility of injury by high temperature under specific conditions.
Alert statements in this Manual
The following alert statements apply to the products in this manual. Each alert statement also appears at the locations needed in this
manual to attract your attention.
This product must be used according to the instruction manual. Failure to observe this may result in impairment of functions
and performance of the product.
This product is not designed or rated for ensuring safety of persons.
Do not use it for such purposes.
Do not open the cover. Doing so may result in electric shock from internally used high voltages.
A lithium battery is built into the Controller and may occasionally combust, explode, or burn if not treated properly. Dispose of the Controller
as industrial waste, and never disassemble, apply pressure that would deform, heat to 100°C or higher, or incinerate the Controller.
Since this product emits a visible light that may have an adverse affect on the eyes, do not stare directly into the light emitted
from the LED. If a specular object is used, take care not to allow reflected light enter your eyes.
Danger of burns
Do not touch the case while the LED is ON or just after power is turned OFF, since it remains extremely hot.
●
Installation Environment
•
Do not use the product in areas where flammable or explosive gases are present.
•
Install the product so that air can flow freely through its cooling vents.
•
Do not install the product close to high-voltage devices and power devices in order to secure the safety of operation and maintenance.
•
Make sure to tighten all installation screws securely.
●
Power Supply and Wiring
•
Make sure to use the product with the power supply voltage specified by this manual.
•
Use a power supply cable and crimp terminals of the specified size. Do not simply connect the twisted ends of the wires directly to
the terminal block.
- Applicable wire size: 1.31 to 2.63 mm
- Terminal screw: M4
•
Keep the power supply wires as short as possible (Max. 10 m).
•
Use a DC power supply with safety measures against high-voltage spikes (safety extra low-voltage circuits on the secondary side).
•
Ground the product's ground terminal to less than 100 Ω.
•
Use a grounding point that is as close as possible and keep the ground wire as short as possible.
•
Wire the Controller to the ground with a separate ground wire. To avoid grounding problems, do not share the ground wire with any
other devices or wire the ground to the building's steel framing.
•
Before turning on the power supply, confirm that the wiring is correct again.
●
Other
•
Use only the camera and cables designed specifically for the product. Failure to observe this may result in malfunction or damage of the product.
•
Always turn OFF the Controller's power before connecting or disconnecting a camera or cable.
•
Do not attempt to dismantle, repair, or modify the product.
•
Should you notice any abnormalities, immediately stop use, turn OFF the power supply, and contact your OMRON representative.
•
Do not touch fluorescent or halogen lights while the power is ON or immediately after the power is turned OFF.
•
Dispose of this product as industrial waste.
●
Regulations and Standards
The Controller complies with the following standards.
EC Directive 2004/108/EC
EN standard EN61326-1
CSA Standard CSA C22.2 No.61010-1
Meanings of Signal Words
Meanings of Alert Symbols
Indicates the possibility of electric shock under specific
conditions.
Indicates the possibility of laser radiation.
WARNING
CAUTION
Precautions for Safe Use
- Crimp terminals
2
8.5 mm max.
8.5 mm max.
2
Advertisement
Table of Contents
