Advertisement
Quick Links
5" and 7" In-Wall
Touch Screens
Installation Guide
Introduction
The Control4® 5" or 7" In-Wall Touch Screen offers complete system control
in an elegant and compact design. These Touch Screens are equipped with a
capacitive Touch Screen surface and four (4) programmable shortcut buttons. The
power options are AC power or Power-Over-Ethernet (PoE). The device may be
connected via WiFi or Ethernet. Available for new construction or retrofits.
Supported Models
• C4-TSWMC5 – 5" In-Wall Touch Screen
• C4-TSWMC7 – 7" In-Wall Touch Screen
Associated SKUs:
• C4-TSWMC5-EG-WH – 5" In-Wall Touch Screen, White
• C4-TSWMC5-EG-BL – 5" In-Wall Touch Screen, Black
• C4-TSWMC7-EG-WH – 7" In-Wall Touch Screen, White
• C4-TSWMC7-EG-BL – 7" In-Wall Touch Screen, Black
Box Contents
Carefully unpack the contents of the box, and make sure the following items
are included in the box. If any item is missing or damaged, please contact your
Control4 Reseller.
• 5" or 7" In-Wall Touch Screen
• Power box (used to power the Touch Screen)
• Two (2) Phillips head screws to attach the power box to the wall
• Warranty card
Wallbox Kit Options
There are four (4) wall box options available to install this Touch Screen. Metal and
plastic wall boxes are available for new construction or retrofit installations.
•
5" or 7" In-Wall Touch Screen Wall Box Kits - New Construction
Plastic Model (C4-NWB57C-P)
Metal Model (C4-NWB57C-M)
•
5" or 7" In-Wall Touch Screen Wall Box Kit - Retrofit
Plastic Model (C4-RWB57C-P)
Metal Model (C4-RWB57C-M)
Refer to the Control4 5" or 7" In-Wall Touch Screen Wall Box Installation Guide
- New Construction or 5" or 7" In-Wall Touch Screen Wall Box Installation Guide -
Retrofit for your wall box installation instructions.
Accessories
• Control4 Power Over Ethernet Injector, sold separately (AC-POE1-B)
• 5" and 7" In-Wall Touch Screens Wall Box New Construction, Plastic
™
(C4-NWB57C-P)
• 5" and 7" In-Wall Touch Screens Wall Box New Construction, Metal (C4-
NWB57C-M)
• 5" and 7" In-Wall Touch Screens Wall Box Retrofit, Plastic (C4-RWB57C-P)
• 5" and 7" In-Wall Touch Screen Wall Box Retrofit, Metal (C4-RWB57C-M)
Requirements for In-Wall Installations
To install the 5" or 7" Touch Screen, you need the following:
• A Home Controller fully installed and configured with a Control4® system.
• Control4 5" and 7" Touch Screen custom wall box installed. See "Wall Box Kit
Options" in this document.
• If using Ethernet with PoE power:
- An Ethernet network installed and available that includes a gateway/router/
switch.
- Control4 PoE Injector (model #AC-POE1-B) or another third-party PoE
Injector or switch (which are certified to UL/ANSI standards).
- Two (2) Ethernet CAT5 cables to support your PoE Injector: (1) one that runs
from the Ethernet gateway/router/switch to the PoE Injector/switch and (2)
one that runs from the PoE Injector/switch to the Ethernet Touch Screen wall
box.
• If using Ethernet with AC power:
- An Ethernet network installed and available that includes a gateway/router/
switch.
- Access to in-wall AC power (a neutral connection is required).
- One (1) Ethernet CAT5 cable that runs from the Ethernet gateway/router/
switch to the Touch Screen.
• If using wireless with AC power:
- Wireless network (WiFi 802.11 b/g) installed and available with a wireless
access point (WAP).
- Access to in-wall AC power (a neutral connection is required).
- A 14-gauge electrical wire long enough to pull between the Touch Screen
and the power source.
Placement, Network Connection, and Power
Options
Place the Touch Screen in a convenient location at eye level, typically near the
entrance of the room, approximately 57 to 61 inches from the floor (see Figure 1).
Figure 1. Touch Screen Placement
New Device
AC Power (unless using PoE)
This device uses an Ethernet or WiFi network connection, and can be powered
using PoE or AC power. Note: Do not attempt to use PoE and AC at the same time.
Option 1: Ethernet Connection with a PoE Injector or a
Third-Party Injector or Switch
PoE injects electrical current into the Ethernet cable using a PoE Injector (model
#AC-POE1-B) or a third-party PoE solution to provide the Touch Screen with power
and a network connection. The 5" and 7" Touch Screens work with the Control4
PoE Injector or a third-party PoE Injector. To set up your PoE and Ethernet
connection with a PoE Injector, see Figure 2.
Figure 2. Ethernet Model - Requires Ethernet Connection to PoE Injector
Place the PoE Injector near your gateway/router/switch. Pull the Ethernet cable
from that location to where you want to install the Touch Screen.
Option 2: Ethernet Connection with AC
No PoE Injector is needed for Ethernet with AC power; the Ethernet is connected
directly to the switch. This power connection requires both neutral and hot
connections (see Figure 3).
Figure 3. Ethernet - Requires Connection to Ethernet and AC Power
Option 3: WiFi Connection with AC
WiFi placement: Place the Touch Screen above a power source, for example, an
outlet. Ensure that you have WiFi in the home (see Figure 4).
Figure 4. WiFi - Requires AC Power and WAP
Front and Rear Panel Description
Front View
Figure 5. Front View - 5" or 7" In-Wall Touch Screen
1
2
1
Display: 5" or 7" viewing area, Touch Screen with 800 x 480 resolution.
2
Shortcut buttons (4): For custom programming; to initiate an action or
sequence of actions. Use Composer Pro or Composer HE to configure these
buttons.
3
Touch Screen Removal: Small hole located under the Touch Screen to remove
the Touch Screen from the wall.
- Front dimensions. 5" Touch Screen (H x W x D): 3.15" x 4.8 x 0.9" (80mm
x 122mm x 23mm); 7" Touch Screen (H x W x D): 4.6" x 6.9 x 0.9" (117mm x
175mm) x 23mm)
- Wall box dimensions. 5" or 7" Touch Screens (H x W x D): 2.7" x 4.1" x 2.4"
(68mm x 104mm x 61mm)
- Power box dimensions. 5" or 7" Touch Screens (H x W x D): 2.8" x 4.5" x 1.8"
(71mm x 114mm x 46mm)
Back View
Figure 6. Back View - 5" or 7" In-Wall Touch Screen and Power Box
1
1
Wire Connection: Hot (H) uses Black wire; Return (R) uses White wire.
2
RJ-45 port for Ethernet Connection: Ethernet port available for either a
standard Ethernet source that provides network communication only OR a
PoE source that provides power to the device and network communication.
Installation
WARNING! For the location where you are installing the Touch Screen,
switch off the circuit breaker or remove the fuse from the fuse box.
AVERTISSEMENT! Pour l'endroit où vous installez l'écran tactile, coupez le
disjoncteur ou enlevez le fusible de la boîte de fusible.
WARNUNG! Für die Position, in der Sie die Berührungseingabe anbringen,
den Circuit breaker ausschalten oder die Sicherung vom Sicherung Kasten
entfernen.
3
2
Advertisement
Related Manuals for Control 4 C4-TSWMC5
Summary of Contents for Control 4 C4-TSWMC5
- Page 1 Option 2: Ethernet Connection with AC box. Supported Models Display: 5” or 7” viewing area, Touch Screen with 800 x 480 resolution. • If using Ethernet with AC power: No PoE Injector is needed for Ethernet with AC power; the Ethernet is connected Shortcut buttons (4): For custom programming; to initiate an action or - An Ethernet network installed and available that includes a gateway/router/ directly to the switch. This power connection requires both neutral and hot sequence of actions. Use Composer Pro or Composer HE to configure these switch. • C4-TSWMC5 – 5” In-Wall Touch Screen connections (see Figure 3). buttons. - Access to in-wall AC power (a neutral connection is required). • C4-TSWMC7 – 7” In-Wall Touch Screen Touch Screen Removal: Small hole located under the Touch Screen to remove - One (1) Ethernet CAT5 cable that runs from the Ethernet gateway/router/ Figure 3. Ethernet - Requires Connection to Ethernet and AC Power the Touch Screen from the wall. switch to the Touch Screen. Associated SKUs: • If using wireless with AC power: - Front dimensions. 5” Touch Screen (H x W x D): 3.15” x 4.8 x 0.9” (80mm - Wireless network (WiFi 802.11 b/g) installed and available with a wireless...
- Page 2 WARNING! Install in accordance with all national, state, and local electrical process and to reset the Touch Screen to the factory default settings. AC Power Connection. The steps below represent a typical U.S. installation. Secure the power box into the wall box using the screws provided. Note: CODES. Connect wires to the AC power source for the Touch Screen according Overtightening power box screws could result in a poor connection between Composer Driver Information to your national and local electrical codes. Your installation may require the Touch Screen and the power box. AVERTISSEMENT! Installez selon tous les national, état, et codes alternative wires and a terminal block. électriques locaux. Align and slide the back of the Touch Screen into the power box. The Touch Choose either the 5” Touch Screen (C4-TSWMC5) or 7” Touch Screen (C4- Screen is magnetic and should snap right into place. • Thread the power cable through the bottom back hole of the wall box straight TSWMC7) driver in Composer Pro and add it to your project. If the driver doesn’t WARNING! This product generates heat. The room must have adequate through to the terminal (Figure 7). Remove the tab covering the hole first. (Optional) To secure the Touch Screen inside the power box, remove the tape appear in the My Drivers list, right-click a driver and select the Restore Default List VENTILATION or the ability to dissipate heat effectively. • Strip the black and white power wire ends to 1/4” if necessary. Using a Phillips covering the bottom security pin (see Figure 9) before attaching the Touch menu option to refresh the list. head screwdriver, loosen the screws on the power box’s terminal block and Screen to the power box.
- Page 3 ™ ATTENTION! Ce produit est pour à l’usage résidentiel ou commercial AND MODIFICATION (Section 3.b.) seulement. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of MAGNET WARNING! Located within the plastic enclosures of this the following: product are strong (rare earth) magnets that are used to attach the face Accompany it with a written offer, valid for at least three years, to give any third party, for a plate to the electrical box. If someone handling or using the product has charge no more than your cost of physically performing source distribution, a complete machine- a pacemaker, defibrillator, or similar electronic device used for health readable copy of the corresponding source code, to be distributed under the terms of Sections 1 purposes, avoid close proximity (closer than 20 inches) to the product and 2 on a medium customarily used for software interchange. until you consult your physician. Magnetic fields can cause damage to The complete text for this license is available on the Control4 web site at: http://www.control4. magnetic storage media (for example, credit cards, video tapes, computer com. hard drives, etc). Keep all magnets at least 20 inches away from all types of magnetic media. Certain electronic devices are sensitive to magnetic Protected under U.S. Patents 7,335,845, 7,106,261 and licensed under U.S. Patents 5,905,442 and 5,982,103 FIELDS and may be damaged permanently or temporarily disabled Regulatory/Safety Information if exposed to a magnetic field that is too strong. Consult the owner’s manuals of your electronic devices for further information. To review regulatory information for your particular Control4 products, see INGESTED magnets can cause serious injuries and may result in death. If the information located on the Control4 website at: http://www.control4.com/ magnets have been ingested (or you suspect they might have been), seek regulatory/ competent medical attention immediately. Warranty AVERTISSEMENT! Aimants! Dans l’emballage en plastique de ce produit sont inclus des aimants très puissants utilisés pour attacher les plaques de surface aux boites électriques. Si quelqu’un, manipulant ou utilisant ce produit est muni d’un pacemaker, défibrillateur ou autre dispositif d’ordre For complete warranty information, including details on consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.