Advertisement
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the userʹs authority to operate this equipment.
C
CAUTION
The SFP OC‐12 contains a Class 1 laser that complies with the
Laser Safety requirements of FDA 21 CFR 1040.10 and 1040.11,
and EN 60825‐1, and ‐2. The SFP OC‐12 is NRTL Listed and CB
Certified to all applicable American and European safety
standards.
!
CAUTION
♦
Per GR‐1089‐CORE Section 9, the SFP OC‐12 does not have
an internal DC connection between battery return and
frame ground.
♦
The ADTRAN system that the SFP OC‐12 is being deployed in
is designed and intended for installation as part of a Common
Bonding Network (CBN), or Isolated Bonding network (IBN).
♦
The SFP OC‐12 can be installed in a DC‐I (isolated) or DC‐C
(common) configuration. For installations where other cards
or the host system have internal connections between battery
return and frame ground, the system would be intended for
deployment only in a DC‐C configuration.
♦
The ADTRAN system chassis frame ground terminal must be
connected to a reliable earth ground to ensure that the metal
enclosure of the SFP OC‐12 is properly grounded via the
backplane connector.
NOTE
♦
The OC‐12 port(s) are optical and therefore are not classified as
any type of port as defined in Appendix B of GR‐1089‐CORE
Issue 5.
♦
This SFP OC‐12 is compliant with SFF‐8472 "Digital
Diagnostics Monitoring Interface for Optical Transceivers,"
Revision 9.3.
♦
This SFP OC‐12 is compliant with the Small Form‐Factor
Pluggable (SFP) Multi‐Source Agreement (MSA).
♦
This product is designed to be deployed in GR‐3108‐CORE
environment class 1 or 2 as defined in GR‐3108‐CORE issue 2.
The SFP OC‐12 is designed to meet the following environmental
classes:
♦
ETSI EN 300 019‐1‐1 "Classification of environmental
conditions; Storage," Class 1.2
Warranty:
ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2010 ADTRAN, Inc. All Rights Reserved.
♦
ETSI EN 300 019‐1‐2 "Classification of environmental
conditions; Transportation," Class 2.3
♦
ETSI EN 300 019‐1‐3 "Classification of environmental
conditions; Stationary use at weather‐protected locations,"
Class 3.3
This product has been evlauated to international safety standards
EN 60950‐1, AS/NZS 60950.1, and IEC 60950‐1. This product
meets the requirements for CE marking under the EMC Directive
and Low Voltage Directive. Standards used to demonstrate
Compliance are EN 300 386 and EN 60950.
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
This product meets EU RoHS Directive 2002/95/EC and/or appli‐
cable exemptions. Refer to www.adtran.com for further infor‐
mation on RoHS/WEEE.
C A U T I O N !
C A U T I O N
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
ADTRAN CUSTOMER CARE:
From within the U.S.
1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442703PG8-22B*
Advertisement
