EWM L1.01-Expert 2.0 Operating Instructions Manual page 4

Contents
Notes on the use of these operating instructions
5.5.5
5.5.6
5.6 Welding task administration (Menu) ............................................................................................. 37
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.6.7
5.7 Change welding procedure (Arc) ................................................................................................. 49
5.8 Online data transfer (network) ..................................................................................................... 49
5.8.1
5.8.2
6 Welding procedure ............................................................................................................................... 51
6.1 MIG/MAG welding ........................................................................................................................ 51
6.1.1
6.1.2
6.1.3
6.1.4
6.1.5
6.1.6
6.1.7
6.1.8
6.1.9
6.1.10
6.1.11
6.1.12
6.2 TIG welding .................................................................................................................................. 68
6.2.1
6.2.2
6.3 MMA welding ................................................................................................................................ 73
6.3.1
6.3.2
6.4 Air arc gouging ............................................................................................................................. 73
7 Rectifying faults.................................................................................................................................... 74
7.1 Resetting JOBs (welding tasks) to the factory settings ................................................................ 74
7.2 Display machine control software version .................................................................................... 74
7.3 Warnings ...................................................................................................................................... 75
7.4 Error messages ............................................................................................................................ 76
4
5.5.4.1 System........................................................................................................... 36
5.5.4.2 Xnet machine ................................................................................................ 36
Load languages and texts ............................................................................................ 36
Record on USB drive .................................................................................................... 36
5.5.6.1 Register USB drive ........................................................................................ 36
5.5.6.2 Start recording ............................................................................................... 36
5.5.6.3 Stop recording ............................................................................................... 36
JOB selection (material/wire/gas) ................................................................................. 37
JOB manager ................................................................................................................ 37
5.6.2.1 Copy JOB to number ..................................................................................... 37
5.6.2.2 Reset current JOB ......................................................................................... 37
5.6.2.3 Reset all JOBs ............................................................................................... 37
Program sequence ....................................................................................................... 38
5.6.3.1 Programs (P 1-15) ....................................................................................... 39
A
5.6.3.2 Overview of the welding parameter switching options .................................. 40
5.6.3.3 MIG/MAG welding ......................................................................................... 42
5.6.3.4 Advanced settings ......................................................................................... 43
5.6.3.5 TIG welding ................................................................................................... 44
5.6.3.6 MMA welding ................................................................................................. 45
Setup mode .................................................................................................................. 46
WPQR welding data assistant ...................................................................................... 47
Welding monitoring ....................................................................................................... 48
JOB display setting ....................................................................................................... 48
Wired local network (LAN) ............................................................................................ 49
Wireless local network (WiFi) ....................................................................................... 50
Welding type ................................................................................................................. 51
Welding power (operating point) ................................................................................... 51
Accessory components for operating point setting ....................................................... 51
Arc length ...................................................................................................................... 51
Arc dynamics (choke effect) ......................................................................................... 51
superPuls ...................................................................................................................... 52
Operating modes .......................................................................................................... 52
6.1.7.1 Explanation of signs and functions ................................................................ 52
6.1.7.2 Automatic cut-out .......................................................................................... 64
coldArc / coldArc puls ................................................................................................... 65
forceArc / forceArc puls ................................................................................................ 65
rootArc/rootArc puls ...................................................................................................... 66
wiredArc ........................................................................................................................ 66
Standard MIG/MAG torch ............................................................................................. 67
Operating modes (functional sequences) ..................................................................... 68
6.2.1.1 Explanation of signs and functions ................................................................ 68
6.2.1.2 Automatic cut-out .......................................................................................... 68
Arc ignition .................................................................................................................... 72
6.2.2.1 Liftarc ............................................................................................................. 72
Hotstart ......................................................................................................................... 73
Antistick......................................................................................................................... 73
099-00L100-EW501
4.7.2019