Communication with heating systems via bacnet or modbus (20 pages)
Summary of Contents for Viessmann Solar EM-S1 Extension
Page 1
Installation and Service Instructions for use by heating contractor ADIO electronics module Function extension for connecting a solar thermal system Solar EM-S1 Extension Product may not be exactly as shown IMPORTANT Read and save these instructions Certified as a component...
Safety Solar EM-S1 Extension Installation / Service Safety, Installation and Warranty Requirements Please ensure that these instructions are read and understood before commencing installation. Failure to comply with the instructions listed below and details printed in this manual can cause product/property damage, severe personal injury, and/or loss of life.
Table of Contents Solar EM-S1 Extension Installation / Service Page Page Safety Safety, Installation and Warranty Requirements ....2 Important Precautions Important Regulatory and Installation Requirements ..4 General Information About these Installation Instructions ......5 Intended Use ............. 5 Spare Parts ............. 5 Installation Mounting the Solar Extension ........
Please carefully read this manual prior to attempting Approvals installation. Any warranty is null and void if these Viessmann boilers, burners and controls are approved for instructions are not followed. sale in North America by CSA International. For information regarding other Viessmann System...
General Information Solar EM-S1 Extension Installation / Service About these Installation Instructions Take note of all symbols and notations intended to draw attention to potential hazards or important product information. Indicates an imminently hazardous situation which, WARNING if not avoided, could result in death, serious injury or substantial product/property damage.
Installation Solar EM-S1 Extension Installation / Service Mounting the Solar Extension Extension kit for installation on a wall 1. Loosen the retaining screws from the extension kit enclosure (do not remove). 2. Remove cover and set aside. 3. Mount the extension module enclosure to the wall using the supplied hardware.
Connections Solar EM-S1 Extension Installation / Service Overview of Electrical Connections Legend Plug 120VAC P1sF Solar circuit pump CAUTION Only use a circulation pump with PWM control. P3fH Transfer pump The electronic modules are static Power supply fÖ sensitive. To avoid damage caused by fÖA...
Connections Solar EM-S1 Extension Installation / Service Rotary Switch S1 The rotary switch is factory preset to 0. Note: The rotary switch can be found on the PCB of the electronics module. Connecting the PlusBus to the Heat Generator For connection to heat generators with external plug, luster terminals or spring-loaded terminals: For the bus connection, disconnect plug jF.
Connections Solar EM-S1 Extension Installation / Service Power Supply Direct power supply WARNING Incorrectly executed electrical installations can result in injuries from electrical current and in equipment damage. Connect the power supply (see page 4) and implement all grounding measures (e.g. RCD circuit) in accordance...
Mixer extension kit for heating circuit with mixer M3 (electronics module) Further accessories PlusBus Commissioning Configuring the solar EM-S1 extension The parameters for the solar EM-S1 extension are set at the heat generator control unit. Heat generator installation and service instructions...
Troubleshooting Solar EM-S1 Extension Installation / Service Repairs Checking the solar circuit pump at output P1 Check the function of the connected components by means of an actuator test: Characteristics of the circulation pump (see the following chapter): Heat generator installation and service...
Troubleshooting Solar EM-S1 Extension Installation / Service Faults Displayed with a Fault Code Meaning of the fault codes Heat generator installation and service instructions Faults Displayed Without a Fault Code Fault Cause Remedy Solar yield too low Temperature sensors interchanged.
Function Solar EM-S1 Extension Installation / Service Function Description of Solar DHW Heating Note: Set or alter the functions described below in the parameters in the “Solar” group. Parameter Description Number Designation The solar circuit pump is switched on according to the following criteria, resulting in the DHW being heated: 1126.0...
Function/Specification Solar EM-S1 Extension Installation / Service Function Description of Solar DHW Heating (continued) Reduction of stagnation time Interval function solar circuit pump If there is an excess of solar energy, the speed of the Set parameter 1719.0. solar circuit pump is reduced before the maximum DHW Activate the interval function in systems where the tank temperature is reached (parameter 1125.0).
Wiring Solar EM-S1 Extension Installation / Service Connection and Wiring Diagram Wiring Diagram Legend Plug 120VAC P1 sF Solar circuit pump (only with PWM control) P3 fH Transfer pump fÖ Power supply fÖA Power supply for accessories Extra low voltage connections PWM1 Speed control, solar circuit pump TS1 % DHW tank temperature sensor NTC 10 kΩ...
Page 16
Solar EM-S1 Extension Installation / Service Scan for digital copy of this document...