Operation - Milwaukee M18 FUEL 2785-20 Operator's Manual

Operator's Zones
To reduce the risk of injury, always
WARNING
use a side handle when using this
tool. Hold securely.
Installing Side Handle
The side handle may be installed on either side of
the gear case. Position the side handle in the loca-
tion which offers best control and guard protection.
To install, thread side handle into side handle socket
and tighten securely.
To reduce the risk of injury, the
WARNING
operator should be instructed in
the use, care and protection of grinding wheels.
Grinding Wheel Selection
Use grinding wheels, and accessories that are:
• correct size as written on tool's nameplate.
• rated at or above the RPM listed on the tool's name-
plate.
• correct accessory, wheel type and grit for the job.
Grinding is the cutting action of thousands of abrasive
grains on the face of a grinding wheel. When grinding
metals such as steel and iron, choose an aluminum
oxide grinding wheel. Select a silicon carbide grinding
wheel for stone and concrete. Use cotton reinforced
wheels for non-ferrous metals.
Type 1 Reinforced 1/8" thick or less Cut-Off Wheels
are suited for small cut-off and shallow notching
operations only. Always handle wheels carefully to
avoid damage. Before installing any wheel, always
inspect it for cracks. If wheel is cracked, discard it to
prevent others from using it.
Fixtex nut
Type 27
or Type 29
grinding
wheel
Type 27 flange
Type 27 guard
Spindle
Spindle lock button
Care of Grinding & Cut-Off Wheels
Grinding/cut-off wheels should be protected from:
• wetness and extreme humidity
• any type of solvent
• extreme changes in temperature
• dropping and bumping
Grinding and cut-off wheels should be stored:
• in an organized way so wheels can be removed
without disturbing or damaging other wheels
• with their safety information
Grinding and cut-off wheels should NOT be dropped,
rolled or bumped.
Discard wheels that have been dropped, rolled,
bumped, subjected to extreme changes in tempera-
ture, or come into contact with solvents or wetness.
Only use accessories with Maxi-
WARNING
mum Safe Operating Speed rated
at least equal to the maximum speed marked on
the power tool. This speed is based on the
strength of the wheel, allowing for a reasonable
measure of safety. It is not meant to imply a best
or most efficient operating speed. Do not exceed
the Maximum Safe Operating Speed.
Installing/Removing Grinding Wheels
Make sure the wheel does not extend beyond the
bottom of the guard. Threaded hub grinding wheels
may require a deeper guard (see "Accessories").
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Properly position the guard.
3. Wipe the flange, nut and spindle to remove dust
and debris. Inspect the parts for damage. Replace
if needed. Use only MILWAUKEE mounting hard-
ware designed for your tool.
4. Place the flange or washer on spindle, as shown.
5. Place the selected wheel on the spindle and align
it with the flange or washer.
6. Press in the spindle lock button while turning the
nut or wheel with hub clockwise. Tighten securely.
7. To remove wheel, remove the battery pack and
reverse the procedure.
Type 28 grinding
Type 27 or Type 29
wheel with hub
grinding wheel with hub
Type 28 guard
Nylon washer
6
Sanding Disc Selection
Use sanding discs and accessories that are:
• correct size as written on tool's nameplate.
• rated at or above the RPM listed on the tool's name-
plate.
• correct accessory, wheel type and grit for the job.
Select the correct type of sanding disc for your job.
Generally, use 24 or 36 grit for heavy stock removal;
50, 60, or 80 grit for medium stock removal and 120
grit for finishing. Always begin with a coarse grit, us-
ing successively finer grits to obtain the desired finish.
•Aluminum Oxide: For fast cutting, general purpose
discs for most metal jobs. Best for cold-rolled steel,
stainless steel or metals requiring tough, fast cutting,
long lasting abrasives.
•Aluminum Zirconia Bi-Cut: Unique grit pattern is
arranged in clusters for faster stock removal and
cleaning. Ideal for removing paint from cars, boats,
etc. without clogging.
•Ceramic: Lasts up to 3 times longer than Aluminum
Oxide Discs. For general metal working. Ideal for
tough jobs.
Installing Backing Pad and Sanding Discs
1. Remove the battery pack. WARNING! Always
remove battery pack before changing or removing
accessories.
2. Wipe the accessories, disc nut and spindle to
remove dust and debris. Inspect the parts for dam-
age. Replace if needed. Use only MILWAUKEE
mounting hardware designed for your tool.
3. Slip backing pad onto spindle with flat side away
from gear case.
4. Place sanding disc on backing pad and secure
assembly to spindle with disc nut.
Disc nut
Sanding disc
Backing pad
Nylon
Washer
Spindle
5. Press in the spindle lock button while turning flange
nut clockwise. Tighten securely.
6. To remove backing pad and sanding disc, remove
the battery pack and reverse the procedure.
Installing/Removing/Cleaning
the Dust Screen
Using the dust screen will increase the performance
and extend the life of the tool.
1. To attach the dust screen, snap the screen over
the tool's gear case.
2. To remove the dust screen, insert a flat screw-
driver into the notch at the top of the dust screen
and pry away from the tool.
3. To clean the dust screen, tap against a hard sur-
face, or blow clean with compressed air.

OPERATION

To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. Never grind without proper
safety equipment.
Controlled Start
The controlled start feature reduces the torque reac-
tion "jerk" when the trigger is pulled.
Always hold the tool firmly with
WARNING
both hands using the handles
provided before and during grinding.
General Operation
1. If you have just installed an accessory or are be-
ginning a period of work, test the wheel by letting it
spin for one minute before applying it to the work-
piece. WARNING! Never use a accessory that has
been dropped. Out-of-balance or damaged acces-
sories can mar workpiece, damage the tool, and
cause stress that may cause accessory failure.
2. Use a clamp, vise or other practical means to hold
your work, freeing both hands to control the tool.
3. WARNING! Hold tool securely with both hands.
To start the tool, grasp the handle and side
handle firmly. Push the lock-off button forward and
squeeze the switch.
4. Allow accessory to come to full speed before
beginning work.
5. Control pressure and surface contact between ac-
cessory and workpiece. WARNING! Never bang
accessory onto work.Too much pressure causes
accessory failure or slows speed.
6. When finished, stop the tool by releasing the
switch. Make sure the tool comes to a complete
stop before laying down the tool.
Using Grinding Wheels
The guard type must match the
WARNING
wheel type to provide maximum
protection for the operator if the wheel should break.
When grinding, hold tool at a 5 to 15 angle, using
o o
constant pressure for a uniform finish. Too great an
angle causes concentrated pressure on small areas
which may gouge or burn work surface.
Hold at a 5° to 15° angle
For best result use only this portion of disc
7