Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for VEVOR NP08001SEC
Summary of Contents for VEVOR NP08001SEC
- Page 1 POPCORN MACHINE INSTRUCTION MANUAL...
- Page 3 This is the original manual, please read all the instructions carefully before operating. VEVOR reserves the right to interpret this user manual. The appearance of the product shall be subject to the product you received. Product technology or further software updates are subject to change without notice.
-
Page 4: Important Safeguards
IMPORTANT SAFEGUARDS 1.Please read ALL the instructions before using your popcorn machine. 2.Do not touch the hot surface directly with your hands. Always operate with handles or knobs. 3.To prevent electrical shock, do not immerse the cord or plug into water or other liquids. 4.Do not let children and minors get close to or touch the machine. -
Page 5: Product Parameters
SAVE THESE INSTRUCTIONS FOR NP08001SEC 1.The model NP08001SEC for commercial use. 2.CAUTION-Risk of electric shock. Replace only with Type A lamp. 3.ATTENTION-Risque d'electrocution.Rempllacez uniquement avec une lampe de type A. Rated 120V,60Hz,E26,Max.150W... -
Page 6: Electrical Schematic Diagram
ELECTRICAL SCHEMATIC DIAGRAM NP08001SE & NP08001SEC： NP16T：... - Page 7 PARTS For Tabletop Models Only: A: Main Unit x 1 pc B: Kettle x 1 pc C: Popcorn Scoop x 1 pc D: Kernel Scoop + Oil Scoop Set x 1 pc Assemble the kettle (B) on the supporters which are built into the main unit (A), and then connect the socket.
- Page 8 For Cart Models Only: Rubber Feet (A) x 2 pcs Support Legs (B) x 2 Support Stands (C) x 2 Wheels (D) x 2 pcs Horizontal Supports Base (E) Horizontal Supports Cabinet Base (G) x 1 pc Cabinet Front with Door x 2 pcs with Screws (F) x 2 pcs (H) x 1 pc...
- Page 9 HEADWEAR Screwdriver (1 pc) and Wrench (2 pcs) are also included. Wheel Bolt M8x (O) x 2 pcs Nyloc Nut M8 (P) x 2 Nut M8 (Q) x 12 pcs Washer (R) x 18 pcs Bolt M8x35 (T) x 2 pcs Bolt M8x16 (U) x 8 Bolt M8x60 (S) x 4 pcs Screw M4x8 (V) x 8 pcs...
- Page 10 EXPLODED VIEW OF THE CART...
- Page 11 POPCORN CART ASSEMBLY STEP 1: Screw one of the RUBBER FEET (A) into the bottom of each SUPPORT LEG (B). Tighten both rubber feet. STEP 2: Insert one WHEEL BOLT (O) into the bottom holes located on each side of the SUPPORT STAND (C). NOTE: Insert the bolt from the inside out, then secure the wheel bolts with one NUT (Q) on each side and tighten them with the wrench.
- Page 12 POPCORN CART ASSEMBLY STEP 4: Attach both HORIZONTAL SUPPORTS-BASE (E) to the same SUPPORT STAND (C) with two BOLTS (T) and one WASHER (R) each. Tighten them with the wrench. STEP 5: Insert two BOLTS (U), each with one WASHER(R),into each SUPPORTLEG(B).Attach SUPPORT LEG (B) to the SUPPORT STAND(C) on the opposite side of the wheels.
- Page 13 POPCORN CART ASSEMBLY STEP 8: Confirm the CABINET BASE (G) is locked in place. Secure the SUPPORT STANDS (C) with the SCREWS (V) as shown in the figure below. Tighten the screws with the screwdriver. STEP 9: NOTE: Before assembling the front and back panels, determine which side you want the cabinet door facing outward.
- Page 14 POPCORN CART ASSEMBLY STEP 10: Remove the pre-assembled screws from the PUSH HANDLE (L). Attach one of the WORKING PLATFORM BRACKETS (K) to one end of the handle. Insert the WORKING PLATFORM (J) to the same bracket using the pre-installed posts. Insert the screw and tighten them. Repeat the steps above to attach the remaining bracket on the other side.
- Page 15 POPCORN CART ASSEMBLY STEP 12: Install the assembled WORKING PLATFORM on the right side of the cart (same side as wheels) with four BOLTS (U), WASHERS(R) and NUTS (Q). STEP 13: Install the assembled HANDLE on the left side of the cart (opposite the wheels) with four BOLTS (U), WASHERS (R) and NUTS (Q).
- Page 16 USING YOUR POPCORN MACHINE 1.Make sure the popcorn maker is unplugged before you do any of the following. 2.Before operation, please check carefully if its voltage is suitable to your country. (Please check if the voltage is matching with rating label specified next to the power cord). 3.Clean the internal surface of the kettle and the external surface of the main unit.
-
Page 17: Cleaning And Maintenance
CLEANING AND MAINTENANCE 1.Wipe the doors, glass and metal surface with a clean damp cloth. DO NOT use any acidic, citrus based cleaners or abrasive cleaners on the acrylic doors as they might cause scratching or dullness. 2.Frequently empty the catch tray of unpopped popcorn kernels and clean it with soap and water. Dry it thoroughly afterwards. - Page 18 E-mail: CustomerService@vevor.com...
- Page 19 POPCORN CART ASSEMBLY...
Need help?
Do you have a question about the NP08001SEC and is the answer not in the manual?
Questions and answers