Adjusting Salt Consumption; Water Hardness; Water Softener - Scandomestic SFO 2204 B User Manual

USING YOUR DISHWASHER
Control Panel
Operation (Button)
1 Power: Press this button to turn on your dishwasher.
2 Delay: Press the button to set the delay time. When pressing
this button, corresponding indicator will be lit.
3 Program: Press this button to select the appropriate washing
program, the selected program indicator will be lit.
4 Start / Pause: Press the button to start the selected washing
program or pause the working program.
Display
5 Warning indicator
Rinse aid
If the " indicator is lit, it means the dishwasher is
low on dishwasher rinse aid and requires a refill.
Salt
If the " " indicator is lit, it means the dishwasher is low
on dishwasher salt and needs to be refilled.
5 Program indicator
Intensive
For heaviest soiled crockery, and normally soiled pots, pans,
dishes etc.With dried-on food.
Normal
For normally soiled loads, such as pots, plates, glasses and lightly
soiled pans.
ECO
This is standard program, it is suitable to clean normally soiled
tableware and it is the most efficient program in terms of its
combined energy and water consumption for that type of table-
ware.
Glass
For lightly soiled crockery and glass.
Rapid
A shorter wash for lightly soiled loads that do not need drying.
90 Min
For normally soiled loads that need quick wash.
7 Delay time
To show the delay time. (2h/4h/8h)

Water Softener

The water softener must be set manually, using the water hard-
ness dial.
The water softener is designed to remove minerals and salts
from the water, which would have a detrimental or adverse ef-
fect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the
water in your area. Your local Water Authority can advise you on
the hardness of the water in your area.

Adjusting salt consumption

The dishwasher is designed to allow for adjustment in the
amount of salt consumed based on the hardness of the water
used. This is intended to optimise and customise the level of salt
consumption.
Please follow the steps below for adjustment in salt consump-
tion.
1. Switch on the appliance;
2. Press the Start/Pause button for more than 5 seconds to
start the water softener set model within 60 seconds after
the appliance was switched on;
3. Press the Start/Pause button to select the proper set accord-
ing to your local environment, the sets will change in the fol-
lowing sequence:
H1->H2->H3->H4->H5->H6;
4. Without any operation in five seconds, the machine will exit
from set mode, the machine is into standby status.

WATER HARDNESS

Setting on the water softener
WATER
HARDNESS
dH 1) Mmol/l
2)
0 - 5 0 - 0.9
6 - 11 1.0 - 2.0
12 -
2.1 - 3.0
17
18 - 3.1 - 4.0
22
23 - 4.1 - 6.1
34
35 - 6.2 - 8.0
45
1) German degree of measurement for the water hardness
2) millimol, internationel unit for water hardness
*factory setting
Please check the section 3 "Loading The Salt Into The Softener"
of PART 1: Generic Version, If your dishwasher lacks salt.
NOTE:
If your model does not have any water softener, you may skip
this section. Water Softener
The hardness of the water varies from place to place. If hard wa-
ter is used in the dishwasher, deposits will form on the dishes
and utensils.
21
Setting on the Digital display
water softener stalls
1 H1-> Rapid Light
bright
2 H2-> 90 Min Light
bright
H3-> 90 Min,
3
Rapid Light bright
4 * H4-> Glass Light
bright
5 H5-> Glass, Rapid
Light bright
6 H6-> Glass, 90
Min Light bright