5. ADJUSTMENT............19 1. COMPLIANCE OF SAFE REPAIR ......3 5-1. Calibration............19 1-1. Cautions during Product Movement ....3 5-2. Changing the Internal Program of N-314 Main Set..20 1-2. Cautions during disassemblying and assembling ...3 5-3. Test mode............21 2. SPECIFICATIONS .............4 6. DEVICE SETTING.............22 2-1.
1. COMPLIANCE OF SAFE REPAIR Be sure to read this Service Manual before providing services. In the PLUS Copyboard, full consideration is taken to ensure the safety for a fire, electric shock, injury, harmful radiation, and substance. Therefore, observe the notice described in this Service Manual so that the safety is kept when providing services.
2.SPECIFICATIONS 2-1. Product Specifications BOARD TYPE (Model name) Standard (N-314) Installation method Self-standing (T-shaped legs), or wall mounting IExternal dimensions W1480 × D675 × H1947*² mm Form (T-shaped legs*¹) Main unit weight 25 kg*³ T-shaped legs weight 12.5 kg Panel size H910 ×...
SPECIFICATION 2-2. Names of the Parts Front Main Unit Frame Cover Sheet Dedicated markers are used on the Sheet to draw diagrams and to write. Numeric Panel Control Panel Input/output terminals Pen Tray (see next page) * Located on the bottom surface. Printer Table The printer* is placed here.
Page 6
SPECIFICATION Input/output terminals The figure is viewed from the back. Rating label (Serial number) USB memory port (type A) Connect a commercially available USB memory device here. Scanned images can be saved. USB B USB A MEMORY The connector is located on the bottom surface of the Main Unit.
FTP server, as previously set. • If you have set “Plural Registration”, go on to enter another Setup Thumbnall Continue ID number using the keypad panel. For details, refer to “N-314 Series Network Manual”. Number of Copies 8 Save (...
Accept IC card Lit green • Turning on the power lights green. Flashing green Preparing for writing to IC card N-314 Lit red IC card error in read/write (3 seconds) Not accept IC card The indicator lights off in the following condition: •...
SPECIFICATION 2-5. Meaninig of Error Messages N-314 If any of the following flashing indications appear in the display window of the control panel, please check the matters described below. Error messages flash for 5 seconds, then stop flashing, remaining lit.
3.TROUBLE SHOOTING By checking operations, it is possible to carry out judgments on malfunction to a certain extent. Carry out the following checks before disassembling the equipment. 1. Press the Standby (On) button and turn on the power. Is the power turned on? No →...
Page 11
• Press the “Save” button three times while pressing and holding the “Power” button. → Test/adjustment mode segment display: <A.P> Press any numeric key. No → The Numeric panel cable is disconnected. The Numeric Panel Unit is defective. Yes → Normal operation N-314 Setup Thumbnall Continue N-314 Setup ・...
4.DISASSEMBLY AND ASSEMBLY 4-1. Tools Required • Phillips screwdriver (+) No. 2 • Phillips screwdriver (–) 4-2. Caution • See “1. Compliance of Safety Repair and Safety Inspection” before disassembling and assembling. • Put on gloves so that you do not cut your hand at the sharp edge of a frame during disassembly and assembly. •...
DISASSEMBLY AND ASSEMBLY 4.4. Disassembly and Assembly This section describes one example of disassembly and assembly procedures. For the actual operation, disassemble and assemble the required parts with reference to “4-3. Disassembly and Assembly Procedures”. * Remove the main set from the stand and proceed with the Endless Sheet. (Perform the operation on a mat.) * Remove the Pen Tray before performing the procedure below.
Page 14
DISASSEMBLY AND ASSEMBLY 2) Remove the Frame Cap PC. (See Fig. 6.) 1.Remove the “S-2” screws shown in the figure 6 and then remove the Frame Cap PC. 2.Disconnect the connector connected to the USB Board shown in the figure 7. 3.Remove the “S-3”...
Page 15
DISASSEMBLY AND ASSEMBLY 5) Remove the Panel Side R. (See Fig. 11) 1. Remove the “S-4” screws shown in the figure 11 and then remove the Panel Side R. Panel Side R Fig.11 7) Remove the Back Panel Unit. (See Fig. 14) 1.Remove the “S-5”...
Page 16
DISASSEMBLY AND ASSEMBLY 3.Remove the “S-3” screws shown in the figure 1.Put the protrusion from the bottom of the SW Panel when 17 and then remove the SW Board. returning the SW Panel to the former position. Note: 2.Slide the protrusion in the direction indicated by the arrow. Pay attention to the wire drawing of the SW Cable 3.Confirm that the hook of the SW Panel is completely put in during assembling.
Page 17
DISASSEMBLY AND ASSEMBLY 10) Remove the Rear Frame. (See Fig. 23) 1.Remove the “S-6” screws shown in the figure 23 and then remove the Rear Frame (two). Rear Frame This side is located upwards. Fig.23 11) Remove the Panel Upper. (See Fig. 24) 1.Remove the “S-4”...
Page 18
DISASSEMBLY AND ASSEMBLY 13) Replace the Endless sheet. 1.Remove the “S-2” screws shown in the figure 27. 2.Remove the Panel Plate shown in the figure 28. 3.Remove the stopper “S-4” screws in the (two upper and lower) Tension Roller Bases shown in the figure 29. 4.Push the Tension Roller Base block shown in the figure 30 into the inside and fix the Tension Roller Bases.
5. ADJUSTMENT 5-1. Calibration Calibration is required in the following cases. • When a Main Board Assy is replaced • When a Sheet Frame Unit is replaced For the replacement of a CIS Unit in the market, usually, use a unit that has been adjusted at a factory. * Be sure to replacing the CIS Unit when any failure occurs in an image.
1) Firmware data for N-314(PX26H_N314_**_**.brn) 2) PC main set (OS: Windows 7/8/8.1/10) 3) USB Cable Preparation Save the extracted N-314 program holder on the desktop screen of PC used. 1. Connect the PC and Copyboard main set using a Removable Disk(D) USB Cable.
ADJUSTMENT 5-3. Test mode 1. Program version display • Insert the plug of an AC Adaptor into the main set to apply the electric current (in the Standby state). • Press the Save button three times while pressing and holding the Power (ON / Standby) button. Test / adjustment mode segment display: <A.P>...
(“CB Setup”) and making the settings via the web on the computer connected to a network. The description here provides operation using the network board’s buttons. For using the network board connected to a network, refer to the separate “N-314 Series Network Manual”. CB Setup (operating the Network board’s buttons) 6-1.
• Header/footer information is registered on the network board via a network. For instructions on creating and registering headers and footers, refer to the separate “N-314 Series Network Manual”. • Depending on the type of printer, the colors may differ from the actual graphic image.
Page 24
DEVICE SETTINGS Function Setting Setting Status Indicators Description Number Item Setting of whether or not to notify the user that characters Disable Color Print or diagrams drawn on the back side of the copyboard’s (Off) (Lit) sheet surface have not been erased. This is effective for Color Print Enable confidential meetings, etc.
7. CABLE AND CABLE CONNECTION CN1 CIS cable 22Pin FFC CN3 Switch cable 7pin red cable CN2 Motor cable 4pin blue cable CN6 USB Board cable 8pin gray cable Unit Main board Assy 100-240VAC AC adapter 12V / 3A Network(LAN) USB Board Printer Motor USB Memory...
Page 27
PARTS LIST 1. PANEL SIDE PARTS No. PARTS NAME Q' ty REMARK Panel Side L N-314 726117800 Panel Side R N-204 726114200 Frame Cap PC N-314 726129400 Frame Cap A N-314 726128900 Frame Cap B N-314 726129500 USB Board Assy...
Page 29
PARTS LIST 2. MAIN BOARD. CIS UNIT. CABLE PARTS No. PARTS NAME Q' ty REMARK CIS Unit 302008 Main Board Shield 726135500 Main Board N-314 726581134 Main Board Sheet 726951100 Cable Cover N-204 726123300 CIS Cable 726590200 Motor Cable 726590100...
Page 31
Panel Plate B N-204 726134200 Rear Frame 726310100 Back Panel Unit S 302001 Endless Sheet N-204 302022 N-31/N314 common Panel Front S Upper N-314 726118700 N-31/N314 common Panel Front S Lower N-314 726117500 Upper/Lower common Panel Rear S Upper 726120900 Cable Clamp...
Page 33
NO Parts Supply Marker Set Marker Black 423283 Marker Red 423284 Marker Blue 423285 Marker Green 423286 Manual CD-ROM N-31 N-31/N-314 common 726469500 Assembly Manual N-31 726469300 Safety Guide No Parts Supply USB Cable 715258900 AC Adapter 726590400 Power Cable (2.5m) BS 715259300 Power Cable (2.5m) CEE...
Page 35
PARTS LIST 5. CARTON PARTS NAME PARTS No. Q' ty REMARK Carton Unit N-204 302024 Carton S Upper N-204 Carton S Lower Packing A Packing B Accessary Box Spacer For Accessary Box Printer Table Stand Carton USA Only Parts Pad L USA Only USA Only Parts Pad R...
Page 37
PARTS LIST 6. N-31-T Q' ty PARTS NAME PARTS No. REMARK Stand Bar (O/S) 726341000 Caster Bar Unit N-31-T 7260090045 Side Bar N-31-T 726338000 Printer Table (Stand Type) 726135900 Edge Holder 723191100 Adapter Holder 726136100 Stand Cap Upper 726321200 Stand Cap Lower 726321100 Front Caster 714660400...
PARTS LIST 7. M-18/N-20-T USA Only T-11 T-15 T-15 T-13 T-15 T-14 T-12 T-16 T-10 S-14 S-15 S-10 S-11 S-13 S-12 S-11 S-12 S-13 S-11 T-19 T-20 T-21 S-12 T-18 T-22 S-11 T-17 S-12 T-24 T-23 T-25 T-17...
Page 39
PARTS LIST 7. M-18/N-20-T PARTS No. PARTS NAME Q' ty REMARK No Parts Supply T Stand (O/S) Side Bar 726332000 Printer Table (Stand Type) 726135900 Edge Holder 723191100 Adapter Holder 726136100 Stand Cap Upper 726321200 Stand Cap Lower 726321100 Front Caster 714660400 Back Caster 714660500...
PARTS LIST 8. SCREWS & WASHERS PARTS No. PARTS NAME Q' ty REMARK M3-6 Cross Recessed Pan Head Double Sems 952530610 M4-8 Cross Recessed Low Head 961540810 M3-8 P-tight Cross Recessed Bind Head 963230810 M4-12 Cross Recessed Low Head 963941210 M4-40 B-tight Cross Recessed Bind Head 963444010 M4-10 Cross Recessed Pan Head Sems...