Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FAAC 104200177
Summary of Contents for FAAC 104200177
- Page 1 Installation Manual Swing Gate System Leading the way ... Leading the way ...
-
Page 2: Table Of Contents
Symbol draws your attention to the notes about the product’s characteristics or operation. FAAC S.p.A. Via Benini, 1 40069 Zola Predosa (BO) - ITALIA Tel.: 051/61724 - Fax: 051/758518... -
Page 3: Ec Declaration Of Conformity For Machines
17) FAAC declines all liability as concerns safety and efficient operation source of danger. of the automated system, if system components not produced by 6) FAAC declines all liability caused by improper use or use other than that FAAC are used. for which the automated system was intended. -
Page 4: Description And Technical Specifications
422 CBCS - 422 CBACS - 422 SBS - 422 CBC - 422 CBAC - 422 SB - 422 CBC PED. - 422 SB PED. The FAAC 422 automated system for swing leaf gates consists of Fig. 2 an enbloc composed of an electric pump and a hydraulic piston which transmits drive to the leaf. -
Page 5: Installing The Automated System
3.2.1. GENERAL RULES FOR DETERMINING THE INSTALLING THE AUTOMATED SYSTEM INSTALLATION DIMENSIONS 3.1. PRELIMINARY CHECKS If the dimensions indicated in table A or B cannot be executed, the following must be considered in order to determine different To ensure a correctly operating automated system, the structure measurements: of the existing gate or gate to be built must satisfy the following to obtain 90°... - Page 6 Secure the operator to the rear attachment with the supplied screws (Fig. 6). Fig. 8 Screw, halfway down, the front attachment onto the rod (ref. Fig.8) and tighten with the supplied nut. Release the operator (see chapter 7). Fully remove the rod to its stop point and make it recede by about 5 mm (Fig.7).
-
Page 7: Start-Up
Fig. 11 Prepare the protective housing and fit it on the operator as shown in Fig. 11. A) Insert the two anti-vibration spacers onto the front flange. B) Introduce the housing, pressing it firmly on the rear cover C) Secure the housing with the self-tapping screw D) Fit the front cover on the housing and fasten it with FIX plug... -
Page 8: Final Operations
- Turn the key 90°clockwise to open the cover. 5. FINAL OPERATIONS - Lift up the cover (Fig. 13). Finish the installation operations as follows: - Back off the screw (Fig. 13, ref. ) which secures the knob, and - Close the cover of the release device with the key. withdraw the knob (Fig. -
Page 9: Restoring Normal Operation Mode
- CLOSE screw (red wording) : gate opening direction. - To reduce torque, turn the screws anti-clockwise. - To increase torque, turn the screws clockwise. Fig. 17 dimensions in mm 11. REPAIRS For any repairs, contact FAAC’s authorised Repair Centres. -
Page 10: Troubleshooting
12. TROUBLESHOOTING The following table will help you identify and solve some particular conditions. I T I e i l . ) . . t i . y l juddering i n i f l i t i f z i r f I . - Page 12 RESTORING NORMAL OPERATION MODE 422 SB - 422 CBC PED. - 422 SB PED. The FAAC 422 automated system for swing leaf gates consists of Before re-locking the operator, cut power to the system. Turn the a hydraulic enbloc composed of an electric pump and a release knob clockwise until it stops.
- Page 14 The descriptions and illustrations contained in this manual are not The descriptions and illustrations contained in this manual are not binding. FAAC reserve the right, whilst leaving the main features of binding. FAAC reserve the right, whilst leaving the main features of the main equipment unaltered, to undertake any modifi...
Need help?
Do you have a question about the 104200177 and is the answer not in the manual?
Questions and answers