Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ronix 8604
Summary of Contents for Ronix 8604
- Page 1 CORDLESS SPRAY GUN 8604 BRUSHLESS...
-
Page 2: Technical Specifications
Continuous Working Time 18-20 min Battery Charging Time 60 mins LED Voltage 16-20V LED Power Flux 150-200LM 7200-8000K Weight 1.1kg Supplied in Ronix Color Box Includes clean needle, shoulder strap, viscosity cup, 2 battery, charger, nozles (1/1.8/2.5mm), Spanner USER MANUAL... -
Page 3: Part List
PART LIST Motor Lock Button LED light adjustable knob Air Cap Trigger Dimmer Battery Tank BRUSHLESS IMPORTANT SAFETY INFORMATION READ AND FOLLOW ALL INSTRUCTIONS Like other power tools, the PORTABLE SPRAY GUN is safe when properly used but can be dangerous if misused. It is the responsibility of the user to read and understand all instructions, and safety precautions before operating the unit and also to use the unit properly. -
Page 4: How To Use
Ronix Service Center. When using parts that do not comply with the specifications and safety devices of the manufacturer, the user assumes all risks and liabilities. WARNING! - Do not spray flammable or combustible materials near an open flame, pilot lights or sources of ignition such as hot objects, cigarettes, motors, electrical equipment and electrical appliances. - Page 5 - Fill the viscosity cup with the diluted paint. - Release your finger to let the paint leak and time it. - Please refer to the thinning chart and picture. Material Run out Time (Sec) 1) Oil enamel 25-60 2) Oil based primer 30-60 3) Oil stain No thinning required...
- Page 6 ASSEMBLY - Make sure the container is empty and dry. BRUSHLESS - Pour thinned paint into the tank, do not exceed the MAX. scale mark, rotate to tighten the tank. Be sure the suction tube is inserted tightly. a) If you are going to be spraying in a downward direction, the angled end of the suction tube should be pointing toward the front of the gun.
- Page 7 CONNECT GUN BODY WITH MOTOR a) Hold the gun with your hand to align the slot on the gun with the slot on the motor and insert it . b) Hold the motor handle with your hand, rotate the right hand clockwise 90°.
- Page 8 REMOVE THE BATTERY PACK a. Hold the spray gun with your hand and press and hold the button on the battery (as shown in the figure). b. Pull out the battery BRUSHLESS HOW TO USE LED LIGHTS a) Adjust the position of the LED light (as shown in the figure). b) Click the LED switch to turn on the LED light.
-
Page 9: Accessory Box
HOOK AND CARRYING a) Shoulder strap can be hung on the hook and used on the shoulder Hook place ACCESSORY BOX BRUSHLESS a) First put the needle into the middle hole and fix it b) Put the nozzle in the outer center c)Put the wrench in the gap in the middle Place the Place the... - Page 10 BRUSHLESS - Adjust the spray patterns The spray pattern shape is adjusted by turning the ears of the air cap to either the vertical, horizontal, or diagonal positions. The positions of the air cap and the corresponding spray pattern shapes are illustrated below. Test each pattern and use whichever pattern is suitable for your application BRUSHLESS...
- Page 11 - Cover screw threads or similar parts of the target object. - It is advisable to test the spray gun on cardboard or a similar surface to find the correct setting. IMPORTANT! Begin spraying outside of the target area and avoid interruptions inside the target area.
- Page 12 STEP ONE: Clean up the gun 1) Unplug sprayer from electrical outlet and pull trigger on spray gun so material inside unit flows back into the container. 2) Empty any remaining material from the container. 3) Fill container approximately 1/2 full with appropriate cleaning solution. For latex, use warm soapy water;...
-
Page 13: Troubleshooting
TROUBLESHOOTING Problem Cause Solution 1.nozzle clogged 1.clean 2.suction tube clogged 2.clean 3.material volume setting 3.turn to the left A. little or no material turn too far to the right 4.insert flow 4.suction tube loose 5.check viscosity 5.material is too thick 6.strain paint 6.inconsistent paint 7.tighten the container... - Page 14 BRUSHLESS...
Need help?
Do you have a question about the 8604 and is the answer not in the manual?
Questions and answers