Table of Contents
Advertisement
Quick Links
10.8V
ANGLE GRINDER/
CUT-OFF TOOL
98437
These instructions accompanying the product are the original instructions. This document is part of the product, keep
it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Related Manuals for Draper Stormforce 98437
Summary of Contents for Draper Stormforce 98437
- Page 1 All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
TECHNICAL DESCRIPTION IDENTIFICATION ....................... 11 UNPACKING AND CHECKING PACKAGING ......................12 DRAPER 10.8V MULTI-TOOL INTERCHANGEABLE BATTERY SYSTEM ....12 WHAT’S IN THE BOX ....................12 PREPARING THE ANGLE GRINDER FITTING/REPLACING ACCESSORIES ..............13 MOUNTING CUTTING DISCS – FIGS.2 – 4 ............. 14 BATTERY PACK –... -
Page 4: Warranty 3.1 Warranty
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period. -
Page 5: Introduction
INTRODUCTION SCOPE This hand held power tool uses abrasive disks for cutting and grinding applications. It is intended for domestic and light commercial use only. Any other application is considered misuse. SPECIFICATION Stock No ........................... 98437 Part No..........................CAG108SF Revolutions per minute (no load): ................... 18,500r/min Disc diameter: ........................... -
Page 6: Health And Safety Information
HEALTH AND SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. -
Page 7: Specific Safety Instructions For Grinder Use
HEALTH AND SAFETY INFORMATION Remove and check setting tools. Some machinery requires the use of additional tools or keys to set, load or adjust the power tool. Before starting the power tool always check to make certain they have been removed and are safely away from the machine. Prevent unintentional starting. -
Page 8: Safety Recommendations For The Correct Use Of Abrasive Products
HEALTH AND SAFETY INFORMATION Secure work. Use clamps or a vice to hold the work. It is safer than using your hands and it frees both hands to operate the tool. Stay alert. Watch what you are doing. Use common sense. Do not operate tool when you are tired. -
Page 9: Safety Recommendations For The Correct Use Of Superabrasives
HEALTH AND SAFETY INFORMATION – Observance of the user’s information from the grinding machine manufacturer. – Safety devices shall be mounting to the machine and shall be secured. – No grinding operations without protection by safety devices. – Use of personal protective equipment according to the type of machine and type of application, e.g. -
Page 10: Residual Risk
HEALTH AND SAFETY INFORMATION RESIDUAL RISK Important note: Although the safety instructions and operating manuals for our tools contain extensive instructions for safe working with power tools, every power tool involves a certain residual risk which can not be completely excluded by safety mechanisms. Power tools must therefore always be operated with caution! –... -
Page 11: Technical Description
TECHNICAL DESCRIPTION IDENTIFICATION (1) On/Off switch. (6) Locking flange. (2) Soft grip. (7) Spindle lock button. (3) 10.8V 1.5Ah Li-ion battery pack (sold separately). (4) Rear flange. (5) Safety guard. – 11 –... -
Page 12: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 13: Preparing The Angle Grinder
PREPARING THE ANGLE GRINDER FITTING/REPLACING ACCESSORIES Warning! Prior to mounting an abrasive wheel ensure the expiry date has not expired, rendering it potentially hazardous. Warning! Selection of the correct accessory, suitable for the intended application is vital. Seek guidance if uncertain of selection. Warning! The rated (no load) revolutions per minute of the tool must not exceed the speed capacity of the accessory. -
Page 14: Mounting Cutting Discs - Figs.2 - 4
Warning! Never press the spindle lock button (3) while the spindle is in motion. BATTERY PACK – FIG.5 Note: This power product is supplied “bare”, without battery pack or charger. Draper 10.8V multi-tool interchange battery packs and FIG. chargers are available separately through all local Draper Tools stockists. -
Page 15: Operation
OPERATION ON/OFF SWITCH – FIG.6 − To start the power tool, push the ON/OFF switch (1) forward. − To lock the ON/OFF switch (1), press the switch down at the front until it latches. − To switch off the power tool, release the ON/ OFF switch (1) or, if it is locked, briefly push down the back of the switch and then release it. -
Page 16: Maintenance And Troubleshooting
10. MAINTENANCE AND TROUBLESHOOTING 10.1 MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. Avoid blocking the air inlets and vacuum the ventilation slots regularly. -
Page 17: Disposal
11. DISPOSAL 11.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •... -
Page 18: Explanation Of Symbols
12. EXPLANATION OF SYMBOLS 12.1 EXPLANATION OF SYMBOLS Class II construction Read the instruction manual. (Double insulated). Wear face mask and safety Lithium-ion product. glasses. WEEE – Waste Electrical & Electronic Equipment. Wear ear defenders. Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish. - Page 19 NOTES – 19 –...
- Page 20 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the Stormforce 98437 and is the answer not in the manual?
Questions and answers