Table of Contents
Advertisement
Quick Links
12V
ANGLE GRINDER/
CUT-OFF TOOL
70300
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Related Manuals for Draper 70300
Summary of Contents for Draper 70300
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION ......................12 UNPACKING AND CHECKING 7.1 PACKAGING ........................13 7.2 DRAPER 12V MULTI-TOOL INTERCHANGEABLE BATTERY SYSTEM ......13 7.3 WHAT’S IN THE BOX ......................13 PREPARING THE ANGLE GRINDER 8.1 FITTING/REPLACING ACCESSORIES ................14 8.2 MOUNTING CUTTING DISCS ..................15 8.3 BATTERY PACK ........................ -
Page 4: Warranty
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period. -
Page 5: Introduction
This hand held power tool uses abrasive disks for cutting and grinding applications. It is intended for domestic and light commercial use only. Any other application is considered misuse. 4.2 SPECIFICATION STOCK NO ..........................70300 PART NO ..........................CAG12VD REVOLUTIONS PER MINUTE (NO LOAD) ..............19,500R/MIN DISC DIAMETER ........................ -
Page 6: Handling And Storage
INTRODUCTION 4.3 HANDLING AND STORAGE Care must be taken when handling this product. • Dropping this power tool could have an effect on its accuracy and could also result in personal injury. This product is not a toy and must be respected. Environmental conditions can have a detrimental effect on this product if neglected. -
Page 7: Health And Safety Information
HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. -
Page 8: Specific Safety Instructions For Grinder Use
HEALTH AND SAFETY INFORMATION Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply before making any adjustments, carrying out maintenance operations or just finishing using the tool. -
Page 9: Safety Recommendations For The Correct Use Of Abrasive Products
– Ensure that sparks resulting from use do not create a hazard e.g. do not hit persons, to ignite flammable substances. – Always use eye and ear protection. – Personal protective equipment such as dust mask, gloves, helmet and apron should be worn. –... -
Page 10: Safety Recommendations For The Correct Use Of Superabrasives
HEALTH AND SAFETY INFORMATION Visual inspection and ring test. Abrasive products must be subjected to a visual inspection as received before mounting. In addition, a ring test shall be executed for vitrified wheels with D>80mm. Damaged abrasive products shall be destroyed. Mounting before starting and information for grinding. -
Page 11: Residual Risk
Further information. The following instructions shall be observed, supplementary to the information of the grinding machine: – Observance of the user’s information of grinding machine manufacturer. – Before starting, safety devices shall be mounted to the machine. – No grinding operations without protection by safety devices. –... -
Page 12: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION (1) On/Off button (4) Rear flange (2) Hand grip (5) Safety guard (3) 12V 1.5Ah/4.0Ah battery pack (6) Locking flange (sold separately). (7) Spindle lock button – 12 –... -
Page 13: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Help Line (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 14: Preparing The Angle Grinder
PREPARING THE ANGLE GRINDER 8.1 FITTING/REPLACING ACCESSORIES Warning! Prior to mounting an abrasive wheel ensure the expiry date has not expired, rendering it potentially hazardous. Warning! Selection of the correct accessory, suitable for the intended application is vital. Seek guidance if uncertain of selection. -
Page 15: Mounting Cutting Discs
8.3 BATTERY PACK – FIG. 4 FIG. 2 Note: This power product is supplied “bare”, without battery pack or charger. Draper 12V multi-tool interchange battery packs and chargers are available separately through all local Draper Tools stockists. -
Page 16: Operation
OPERATION 9.1 ON/OFF SWITCH – FIG. 5 To start the angle grinder/cut-off tool, push the on/off button (1) forward. To lock the on/off switch, press the switch down at the front until it latches. To switch off the power tool, release the on/off switch or, if it is locked, briefly push down the back of the switch and then release it. -
Page 17: Maintenance And Troubleshooting
10. MAINTENANCE AND TROUBLESHOOTING 10.1 MAINTENANCE Regular inspection and cleaning reduces the necessity for maintenance operations and will keep your tool in good working condition. The motor must be correctly ventilated during tool operation. Avoid blocking the air inlets and vacuum the ventilation slots regularly. -
Page 18: Disposal
11. DISPOSAL 11.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •... -
Page 19: Explanation Of Symbols
12. EXPLANATION OF SYMBOLS 12.1 EXPLANATION OF SYMBOLS For indoor use only. Read the instruction manual. Do not expose to rain. Wear face mask and safety Fuse protective device. glasses. Wear ear defenders. Polarity indication. Wear protective gloves. Rated voltage. Do not abandon into the Class II construction environment. - Page 20 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the 70300 and is the answer not in the manual?
Questions and answers