Table of Contents
Advertisement
Quick Links
AIR
DIE GRINDERS
65130 & 65137
Stock No. 65130 shown
These instructions accompanying the product are the original instructions. This document is part of the product, keep
it for the life of the product, passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. Following all the general safety
instructions contained in this manual will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of
the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper Stormforce 65130
Summary of Contents for Draper Stormforce 65130
- Page 1 All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product. Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools policy of continuous improvement determines the right to make modifications without prior warning.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS TABLE OF CONTENTS TITLE PAGE INTRODUCTION ......................2 REVISIONS ........................2 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT ........2 COPYRIGHT NOTICE ....................2 CONTENTS CONTENTS ......................... 3 WARRANTY WARRANTY ......................... 4 INTRODUCTION SCOPE ........................5 SPECIFICATION ......................5 HANDLING AND STORAGE ..................5 HEALTH &... -
Page 4: Warranty 3.1 Warranty
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period. -
Page 5: Introduction
INTRODUCTION SCOPE Straight and 90° composite body high speed die grinders, with a 6mmØ collet used to clamp grinding stones. SPECIFICATION Stock no..............65130 ............65137 Part no..............SFAG ........... SFAG90 Collet size ..............6mm ............6mm Offset ................0° .............. 90° Revolution per minute (no load) ......25,000r/min .........20,000r/min Max. -
Page 6: Health & Safety Information
HEALTH AND SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. -
Page 7: Additional Safety Instructions For Air Die Grinder Tools
HEALTH AND SAFETY INFORMATION Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply before making any adjustments, carrying out maintenance operations or just finishing using the tool. -
Page 8: Safety Recommendations For The Correct Use Of Abrasive Products
HEALTH AND SAFETY INFORMATION − Personal protective safety glasses shall be worn. Gloves and protective clothing are recommended. − Assess the need for personal protection and the provision for dust collection appropriate for the material to be worked on. − Die grinders are not insulated for coming into contact with electric power sources. −... -
Page 9: Connection To The Power Supply
HEALTH AND SAFETY INFORMATION CONNECTION TO THE POWER SUPPLY Caution: Risk of electric shock. Do not open. This appliance is supplied with an approved plug and cable for your safety. The value of the fuse fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute is of the correct rating, approved to BS1362 and ASTA or BS Kite marked. -
Page 10: Technical Description
TECHNICAL DESCRIPTION IDENTIFICATION Stock No. 65130 shown (1) Collet nut. (5) 1/4" BSP (female air inlet). (2) Output shaft. (6) Exhaust. (3) Composite body. (7) Trigger. (4) Air flow (speed) selector. (8) Trigger safety lever. – 10 –... -
Page 11: Packaging
Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product. -
Page 12: Air Supply
This air tool operates at a maximum pressure of 90psi and must be controlled via a combination pressure regulator, in-line lubricator and moisture filter such as the Draper range (see your local Draper stockist). This, along with proper maintenance, will ensure a constant supply of dry air and lubricating oil at all times (see illustration below). -
Page 13: Assembly
1/4" BSP male thread whip hose* (11) will be required. Wind a length of PTFE tape** (12) around the thread before securing the hose in place. The connection must be tight for an airtight union. * Draper Stock No.54438. (12) ** Draper Stock No.63389. FIG. -
Page 14: Operation And Use
10. OPERATION AND USE Note: Disconnect from the air supply before carrying out adjustment, servicing or maintenance. 10.1 INSERT TOOL – FIG. 3 Warning: Select the grinding point appropriate for the application, speed rated to the die grinder and with the correct shaft diameter for the collet. Inspect the grinding point before use. -
Page 15: Maintenance
11. MAINTENANCE 11.1 BEFORE-USE MAINTENANCE CHECKS Before connection to the air supply: − Drain the compressor reservoir of condensate. − Drain the air lines of condensate. − Drain the combined separator filter, regulator, water trap. − Fill up the combined separator filter, regulator, lubricant reservoir. −... -
Page 16: Troubleshooting
‘O’ rings throttle valve − Replace ‘O’ ring or return dislodged from seat inlet to service centre. valve. We recommend the use of Draper Air Tool Oil: 250ml = Stock No.34679, 500ml = Stock No.34681, 1Litre = Stock No.34682. – 16 –... -
Page 17: Disposal
13. DISPOSAL 13.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •... -
Page 18: Explanation Of Symbols
14. EXPLANATION OF SYMBOLS 14.1 EXPLANATION OF SYMBOLS WEEE – Waste Electrical & Electronic Equipment. Read the instruction manual. Do not dispose of Waste Electrical & Electronic Equipment in with domestic rubbish. Direction of rotation. Warning! Wear suitable eye/face protection. Warning! Wear ear defenders. - Page 19 NOTES – 19 – – 19 –...
- Page 20 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the Stormforce 65130 and is the answer not in the manual?
Questions and answers