Draper PT820 Instructions Manual

Draper PT820 Instructions Manual

820w 230v 115mm angle grinder

Advertisement

Quick Links

INSTRUCTIONS FOR
820W 230V 115mm
Angle Grinder
Stock No.20922
Part No.PT820
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS PRODUCT.
GENERAL INFORMATION
These instructions accompanying the product are the original instructions. This document is part of the product, keep it
for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed, and
contains all the necessary information to ensure its correct and safe use. By following all the general safety instructions
contained in this manual, it will ensure both product and operator safety, together with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT820 and is the answer not in the manual?

Questions and answers

Summary of Contents for Draper PT820

  • Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
  • Page 2: Title Page

    Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact.
  • Page 3: Table Of Contents

    CONTENTS 2.1 CONTENTS Page content Page TITLE PAGE INTRODUCTION ......................2 REVISION HISTORY....................2 UNDERSTANDING THIS MANUAL .................2 COPYRIGHT NOTICE....................2 CONTENTS CONTENTS .......................3 GUARANTEE GUARANTEE ......................4 INTRODUCTION SCOPE ........................5 SPECIFICATION ......................5 HANDLING & STORAGE ..................5 HEALTH & SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE ........6 SPECIFIC SAFETY INSTRUCTIONS FOR GRINDER USE..........6-8 SAFETY RECOMMENDATIONS FOR THE CORRECT USE OF ABRASIVE PRODUCTS..8 SAFETY RECOMMENDATIONS FOR THE CORRECT USE OF SUPERABRASIVES...9...
  • Page 4: Guarantee

    This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period.
  • Page 5: Introduction

    This hand held power tool uses abrasive disks to grind metals or masonry. It is intended for domestic and light commercial use only. Any other application is considered misuse. 4.2 SPECIFICATION Stock no ..........................20922 Part no ..........................PT820 Motor: Rated voltage ...................... 230V~ Rated frequency ....................50Hz Rated input ......................
  • Page 6: Health & Safety Information

    HEALTH & SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully.
  • Page 7 HEALTH & SAFETY INFORMATION Ensure that mounted wheels and points are fitted in accordance with the manufacturer’s instructions; Ensure that blotters are used when they are provided with the bonded abrasive product and when they are required; Ensure that the abrasive product is correctly mounted and tightened before use and run the tool at no-load for 30 seconds in a safe position, stop immediately if there is considerable vibration or if other defects are detected.
  • Page 8: Safety Recommendations For The Correct Use Of Abrasive Products

    HEALTH & SAFETY INFORMATION 10. Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation.
  • Page 9: Safety Recommendations For The Correct Use Of Superabrasives

    HEALTH & SAFETY INFORMATION 5.4 SAFETY RECOMMENDATIONS FOR THE CORRECT USE OF SUPERABRASIVES. General. Superabrasives are breakable and shall therefore be handled with utmost care! The use of damaged or improperly mounted or used superabrasives is dangerous and can cause serious injuries. b.
  • Page 10: Caution: Risk Of Electric Shock. Do Not Open

    HEALTH & SAFETY INFORMATION 5.5 CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Caution: Risk of electric shock. Do not open. This appliance is supplied with a moulded 3 pin mains plug for your safety. The value of the fuse fitted is marked on the pin face of the plug.
  • Page 11: Technical Description

    TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Spindle lock button Moulded plug & cable On/Off locking switch Quick release grinding guard Rear hand grip Locking flange...
  • Page 12: Unpacking & Checking

    Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the product.
  • Page 13: Preparing The Grinder

    PREPARING THE GRINDER 8.1 FITTING AUXILIARY HANDLES - FIG. 1 FIG. 1 NOTE: Remove the plug from the socket before carrying out adjustment, servicing or maintenance. For reasons of safety, when working with this type of electric power tool, the operator must always use the auxiliary handle Screw the handle clockwise, into one of the three threaded apertures best suited to the application and...
  • Page 14: Fitting/Replacing Accessories (Not Supplied)

    NOTICE B, C, D (FIG.3): For cutting applications, and to comply to current legislation, it is necessary to replace the “grinding” guard supplied with this machine with a “cutting” guard (Draper Stock No.41430) and must be fitted for your safety.
  • Page 15: Setting The Grinder

    SETTING THE GRINDER 9.1 FITTING GRINDING DISCS - FIG. 4 Press and hold the spindle lock button . Loosen the locking flange anti-clockwise using the pin spanner supplied . The spindle may rotate slightly before the spindle lock fully engages. Remove the locking flange only.
  • Page 16: Grinding

    NOTICE Cutting operations should only be attempted with the “cutting” guard fitted to this grinder. (Draper Stock No.41430.) Please contact Draper Tools for further information on how to purchase this optional accessory. This guard must be fitted for your safety.
  • Page 17: Troubleshooting

    10. TROUBLESHOOTING 10.1 TROUBLESHOOTING WARNING: For your own safety, turn the switch off and remove the plug from the power supply socket. PROBLEM POSSIBLE CAUSE REQUIRED ACTION • Motor does not • Fuse. • 5 amp time delay fuse or start.
  • Page 18: Explanation Of Symbols

    12. EXPLANATION OF SYMBOLS 12.1 EXPLANATION OF SYMBOLS Warning! Read instruction manuals before operating and servicing this equipment. Warning! Wear suitable eye/face protection. Warning! Wear ear defenders. Warning! Wear dust mask. Class II construction (Double insulated) WEEE Do not dispose of Waste Electrical &...
  • Page 19: Disposal

    13. DISPOSAL 13.1 DISPOSAL - At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. - Contact your local authority for details of collection schemes in your area. In all circumstances: •...
  • Page 20 - Sales Desk: (023) 8049 4333 - General Enquiries: (023) 8026 6355 - Service/Warranty Repair Agent For aftersales servicing or warranty repairs, please contact the Draper Tools Helpline for details of an agent in your local area. YOUR DRAPER STOCKIST RDKC0916...

This manual is also suitable for:

20922

Table of Contents