Integra DRX-2.1 Basic Manual page 46

> Specifications > Advanced Setup
■ 4� Level Calibration
Setting Item Default Value
Front Left 0 dB
Center 0 dB
Front Right 0 dB
Height Left 0 dB
Height Right 0 dB
Surround Right 0 dB
14
> Listening Modes
Setting Details
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
• The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
• The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
> Network Functions
Setting Item Default Value
Surr Back Right 0 dB
Surr Back Left 0 dB
Surround Left 0 dB
Subwoofer 0 dB
■ 5� Dolby Enabled Speaker
Setting Item Default Value
Dolby Enabled 6.0 ft/1.80 m
Speaker to
Ceiling
AccuReflex Off
• This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".
> Basic Manual
Troubleshooting Supplementary Information, etc� |
Setting Details
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
• The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
• The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Select a value between "−15 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Setting Details
Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between "0.1
ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
• The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not to be used
"On": When this function is to be used