Table of Contents
Advertisement
1-6
JOINING OPEN CASES IN A LINEUP
JOINING AND SEALING HARDWARE
SEALER SILICONE ADHESIVE
GASKET 1/2 X 1/2 X 180
SCREW-SHEET METAL #8 X 5/8 PHIL HX HD
SCREW-CAP 1/4 x 3/4 HEX
BOLT HEX CAP 5/16 x 3/4
BOLT 5/16 x 2 3/4 GRADE 5 ZINC PLATED TAP
BOLT- TAP, 5/16 x 4 1/2, STEEL, ZINC FINISH, GR5 (Qty Varies)
BOLT- TAP, 5/16 x 7, STEEL, ZINC FINISH, GR5
WASHER-FLAT 5/16" ZINC (Qty Varies)
LOCKWSHR 1/4 SPLT STL
LOCKWSHR 5/16 SPLT STL
NUT-HEX 1/4
NUT-HEX 5/16 STEEL ZINC FINISH GRADE 8 (Qty Varies)
NUT-HEX 3/8-24 SERRATED FLANGE
PIN-ALIGNMENT
CONE-CASE ALIGNMENT (Qty Varies)
PLATE-BOTT DOOR RAIL ALIGNMENT
BRACKET-CASE JOINING
BRACKET-FASCIA ALIGNMENT IC2 & IC3
COVER-HAND RAIL JOINT
TAPE-BUTYL 1/16 x 2" X 49"
Screw-Sheet Metal #8 x 5/8
Screw-Sheet Metal #8 x 5/8
Screw-Cap 1/4 x 3/4
Screw-Cap 1/4 x 3/4
Bolt-5/16 x 3/4
Bolt-5/16 x 3/4
Bolt-5/16 x 2 3/4
Bolt-5/16 x 2 3/4
Bolt-5/16 x 4 1/2
Bolt-5/16 x 4 1/2
Bolt-5/16 x 7
Bolt-5/16 x 7
Washer Flat-5/16
Washer Flat-5/16
Washer Lock-1/4
Washer Lock-1/4
Washer Lock-5/16
Washer Lock-5/16
Nut Hex-1/4
Nut Hex-1/4
Nut Hex-5/16
Nut Hex-5/16
Nut Hex-3/8 Serr Flange
Nut Hex-3/8 Serr Flange
Pin-Alignment
Pin-Alignment
Cone-Alignment
Cone-Alignment
Plate-Bottom Door Rail Alignment
Plate-Bottom Door Rail Alignment
Bracket-Case Joining
Bracket-Case Joining
Bracket-Fascia Alignment IC2 & IC3
Bracket-Fascia Alignment IC2 & IC3
Cover-Handrail Joint
Cover-Handrail Joint
P/N 0535974 _R
Multi Deck
Qty/Each
Do not pull cases together with bolts. Cases must be moved
together as close as possible. Follow sequence balloons to
tighten bolts.
Apply gasket to only one side of case joint.
Remove end shipping braces as described on Page 1-4.
Cases must be leveled as described on Page 1-5.
Removed any casters - if installed.
Install case lineup from left to right.
Remove shelves, display racks, pans & interior back panels at
the joining area.
Insert gasket into case channels the entire length with no gaps.
Do not stretch gasket, especially around corners.
Do not butt gaskets, always overlap them.
Remove paper backing after gasket has been applied.
Perimeter gasket is required by NSF.
Apply a continuous bead of neutral curing silicone sealant.
Joints must be air tight to prevent formation of ice of condensation.
U.S. & Canada 1-800-922-1919 • Mexico 01-800-890-2900 • www.hussmann.com
Note:
See PAGE 1-21 at end of manual for joining
rear load and door cases.
Convertible
Single Deck
Qty/Each
1
1
2
1
N/A
1
N/A
N/A
1
1
2
N/A
5
2
1
1
13
5
N/A
N/A
1
1
N/A
N/A
9
4
4
N/A
1
1
4
2
N/A
N/A
4
N/A
N/A
1
1
1
1
1
IMPORTANT:
Door Multi
Qty/Each
Deck Qty/Each
1
1
1
2
N/A
N/A
N/A
2
1
1
N/A
2
1
5
1
1
3
13
N/A
2
1
1
N/A
2
3
9
N/A
4
1
N/A
2
4
N/A
1
N/A
4
N/A
N/A
1
N/A
1
1
Advertisement
Table of Contents
