Start Up / Operation; Load Limits; Stocking - Hussmann Insight Installation & Operation Manual

P/N 3032067_E

START UP / OPERATION

See the merchandiser's Technical Data Sheet
(TDS) for refrigerant settings and defrost
requirements . Bring merchandisers down to the
operating temperatures listed on the data sheet .
Excessive ambient conditions may cause condensation
and therefore sweating of doors. Facility operators
should monitor doors and floor conditions to
ensure safety of persons.
ANSI Z535.6-2011 (R2017)
Each four-foot section has its own evaporator
Page 18
coil and pre-set adjustable thermostatic expan-
sion valve (TEV) . Evaporator super heat must be
Providing Information About Safety Messages in Collateral Materials and Product
checked on all cases during startup .
The TEV has been factory set to provide the
recommended performance settings as specified
A1 Explanation of Signal Words and Symbols
on merchandiser data sheets . Only a certified
Signal words and safety symbols that are used in a product's collateral materials or on the product may
technician should adjust these valves .
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
The meaning of the safety alert symbol may be provided in collateral materials. The following artwork may
be used for this purpose.
A1.2 Signal Words
The meaning of the different signal words as defined by the ANSI Z535.6 and ANSI Z535.4 standards
TEV
may be explained in collateral materials. The following artwork may be used for this purpose.
»
Always be sure to replace TEV Cap, missing TEV Cap
could result in refrigerant loss.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate safety messages (e.g., text
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral materials may be explained in
collateral materials.
HUSSMANN CORPORATION • BRIDGETON, MO 63044-2483 U.S.A.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
No reproduction or networking permitted without license from IHS
STARTUP / OPERATION
Annex A
Safety Signs and Labels
(Informative)
This is the safety alert symbol. It is used to alert you
to potential physical injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE is used to address practices not related to
physical injury.
Safety instructions (or equivalent) signs indicate specific
safety-related instructions or procedures.
© 2017 National Electrical Manufacturers Association
Licensee=Hussmann Corp/8160899001, User=Trevett, Jason
Not for Resale, 02/16/2021 11:49:55 MST

LOAD LIMITS

Each merchandiser has a load limit . Shelf life
of perishables will be short if load limit is vi-
olated . At no time should merchandisers be
stocked beyond the load limits indicated .

STOCKING

ANSI Z535.6-2011 (R2017)
Page 18
Product should not be placed inside of mer-
Providing Information About Safety Messages in Collater
chandisers until merchandiser is at proper
operating temperature . Proper rotation of
product during stocking is necessary to prevent
A1 Explanation of Signal Words and Symbols
product loss . Always bring the oldest product
Signal words and safety symbols that are used in a product's collateral ma
to the front and set the newest to the back .
be defined in collateral materials if space is available.
A1.1 Safety Alert Symbol
Air discharge and return flues must remain
The meaning of the safety alert symbol may be provided in collateral mate
be used for this purpose.
open and free of obstruction at all times to
provide proper refrigeration and air curtain
performance . Do not allow product, packages,
signs, etc . to block these grilles . Do not use
non-approved shelving, baskets, display racks,
or any accessory that could hamper air curtain
A1.2 Signal Words
performance .
The meaning of the different signal words as defined by the ANSI Z535.6
may be explained in collateral materials. The following artwork may be use
»
Case ventilation openings must be clear of any
obstructions. Do not damage the refrigerant
circuit.
A1.3 Other Highlighting Conventions
The meaning of any other highlighting conventions used to differentiate sa
manipulations, indention, etc.) may be explained in collateral materials.
A1.4 Safety Symbols
The meaning of any safety symbols used on safety labels or collateral ma
collateral materials.
Copyright National Electrical Manufacturers Association
Provided by IHS Markit under license with NEMA
No reproduction or networking permitted without license from IHS
Low Temperature
4-1
Annex A
Safety Signs and Labels
(Informative)
This is the safety alert symbol. It
to potential physical injury hazar
messages that follow this symbo
injury or death.
DANGER indicates a hazardou
avoided, will result in death
WARNING indicates a hazardo
avoided, could result in dea
CAUTION indicates a hazardou
avoided, could result in min
NOTICE is used to address pra
physical injury.
Safety instructions (or equivale
safety-related instructions o
© 2017 National Electrical Manufacturers Assoc
Licensee=Hussmann Corp/8160899001,
Not for Resale, 02/16/2021 11:49:55 MST
Merchandisers