Related Manuals for Hussmann Q3-SP
Summary of Contents for Hussmann Q3-SP
- Page 1 Q 2 - S P N D E L I S E L F S E R V I C E C A S E I N S T A L L A T I O N & O P E R A T I O N G U I D E...
-
Page 2: Table Of Contents 1. General Instructions
Check your shipment for any possible shortages of material. If a shortage should exist and is found to be the responsibility of Hussmann Chino, notify Hussmann Chino. If such a shortage involves the carrier, notify the carrier immediately, and request an inspection. -
Page 3: Table Of Contents
Table of Contents 1. General Instructions...............2 3. Cut and Plan Views ..............4 4. Installation................5 5. Plumbing .................8 6. Refrigeration ................9 8. Finishing Touches ..............11 9. User Information..............12 13. Troubleshooting Guide ............17 7. Electrical................10 10. Maintenance................13 11. Wiring Diagrams Index............15 12. -
Page 4: Cut And Plan Views
3. Cut and Plan Views... -
Page 5: Installation
4. Installation Location floor the exact dimensions of where the cases will sit. Snap chalk line for front and back positions of The refrigerated merchandisers have been designed base rail or pedestal. Mark the location of each joint for use only in air conditioned stores where temperature front and back. - Page 6 Installation (Cont'd) clamps. Make sure case is level from front to back masking tape on inside and outside of rear mullion and side to side on inside bulkheads at joint. (apply additional silicone if necessary). Remove tape applied on line #4. 8.
- Page 7 Installation (Cont'd) Q2-SPN CASE TO CASE ALIGNMENT TOP BOLT LOCATION ALIGNMENT TOP BOLT PRIMARY ACCESS THROUGH CONDIMENT PANS BOLT HOLE REAR BOLT LOCATION TOP BOLT SECONDARY ACCESS THROUGH INTERIOR PANELS OR HONEYCOMB (WHEN SECTION HAS NO CONDIMENT PANS) ACCESS FROM UNDERSIDE BOLT HOLE FRONT BOLT ACCESS...
-
Page 8: Plumbing
Installation (Cont'd) Q3-SP CASE TO CASE ALIGNMENT Bulkhead Cap Installation Place Bulkhead Cap Over Joint Seal With Butyl 5. Plumbing Waste Outlet and P-TRAP any one line. Double P-TRAPS in series will cause a lock and prevent draining. The waste outlet is located off the center of the case on 3. -
Page 9: Refrigeration
6. Refrigeration Refrigerant Type Electronic Expansion Valve (Optional) The standard refrigerant will be R-404A unless otherwise A wide variety of electronic expansion valves and case specified on the customer order. Check the serial plate on controllers can be utilized. Please refer to EEV and the case for information. -
Page 10: Electrical
7. Electrical Wiring Color Code BEFORE SERVICING ALWAYS DISCONNECT ELECTRICAL POWER AT THE MAIN DISCONNECT WHEN SERVICING OR REPLACING ANY ELECTRICAL COMPONENT. This includes (but not limited to) Fans, Heaters Thermostats, and Lights. Field Wiring and Serial Plate Amperage Field Wiring must be sized for component amperes printed CASE MUST BE GROUNDED on the serial plate. -
Page 11: Finishing Touches
8. Finishing Touches Installing Splashguard Bumper Installation Tips 1. Start to attach the bumper at one end of the lineup, After merchandisers have been leveled and joined, and preferably on a straight case. all drip piping, electrical and refrigeration work has been completed, install the splashguards. -
Page 12: User Information
4. Rinse thoroughly. of the product must be controlled to maximize life of the product. Hussmann cases were not designed to “heat up” 5. Dry completely before resuming operation. or “cool down” product - but rather to maintain an item’s Cleaning Glass and Mirrors proper temperature for maximum shelf life. -
Page 13: Maintenance
ELECTRICAL COMPONENT. Copper Coils This includes (but not limited to) Fans, Heaters Thermostats, and Lights. The copper coils used in Hussmann merchandisers may be repaired in the field. Materials are available from local refrigeration wholesalers. CAUTION Hussmann recommends using #15 Sil-Fos for repairs. - Page 14 Maintenance (Cont'd) 2. Clean With the Polish Lines Glass Replacement and Adjustment Some stainless steels come with visible polishing Instructions lines or “grain”. When visible lines are present, you should ALWAYS scrub in a motion that is parallel to In order to replace or adjust the glass, the glass must be them.
-
Page 15: Wiring Diagrams Index
11. Wiring Diagrams Index Model Description Size Digram # Q2-SP-N-4R W/OP- 3003959 TIONAL TOP LIGHT Q2-SP-N-5R W/OP- 3064454 TIONAL TOP LIGHT Q2-SP-N6-R 1H95151 Q2-SPN-8R 3008496 Q2-SP-N-10R W/OP- 3003958 TIONAL TOP LIGHT Q2-SPN-R Q2-SP-N12-R 3013450 Q2-SPN-22.50-R 22.5° 3070614 Q2-SPN-45OS 45° 2H21329 Q2-SPN-30OS 30°... - Page 26 13. Troubleshooting Guide Problem Possible Cause Possible Solution Case temperature is Ambient conditions may Check case position in store. Is the case located near an too warm. be affecting the case open door, window, electric fan or air conditioning vent that operation.
- Page 27 Troubleshooting Guide (Cont'd) Problem Possible Cause Possible Solution Water has pooled Case drain is clogged. Clear drain. under case. PVC drains under case Repair as needed. may have a leak. Case tub has unsealed Seal as needed. opening. If the case is in a line- Install case to case joint and seal as needed.
- Page 28 August 31, 2018 This warning does not mean that Hussmann products will cause cancer or reproductive harm, or is in violation of any product-safety standards or requirements. As clarified by the California State government, Proposition 65 can be considered more of a ‘right to know’...
- Page 29 Additional copies of this publication may be obtained by contacting: They can be found on a small metal plate on the unit. Hussmann® Chino Please note them below for future reference. 13770 Ramona Avenue • Chino, California 91710...
Need help?
Do you have a question about the Q3-SP and is the answer not in the manual?
Questions and answers