Plantronics HL1 User Manual

18890 Plx. HL1_HL2 11/17/03 6:39 PM Page 1
Guide
HL2 &
Accessory
Handset Telephone
HL2 DIAGRAM
2
5
HL1
1
6
HL2
2
5
7
8
9
10
11
c . I n c s n i r o n t a P l 3 ©10•200
User
HL1 Models
Lifter
HL2 TELEPHONE HANDSET LIFTER ACCESSORY
3
HL1
CA10
4
HL1 Adapter Power Plug
1
Lifter Motor Assembly
2
HL1 Expandable Base
3
HL1 Ringer Detector
4
and cable P/N 46780-01
Lifter Arm P/N 46778-01
5
HL1 Lifter Base
6
65688-01 U.S.A. the
www.plantronics.com
800.544.4660
95060 California Cruz, Santa
Street Encinal 345
B
A
HL1
HL2
HL2
A20
HL2 Adapter Housing
7
HL2 Adapter Power Plug
8
Adapter Power Line
9
Accessory Jack
10
Ringer Detector Jack
11
(only with the HL1 Lifter)
in Printed
reserved. rights
warranty. limited this by covered not
our of details full the for center service
province. to province or state to
have also may you and rights, legal
PRODUCTS. THE FOR WARRANTY COMPLETE
provided. numbers the at centers service
i additional need you If 540-8363.
544-4660 (800) at Plantronics contact
parts. or Products new or refurbished/remanufactured/pre-owned
reconditioned/ equivalent functionally
conform not do that Products the replace
origi- the with user end the are you
the of purchase of date the from
Canada. and States United the in
Plantronics by certified or sold manufactured,
of workmanship and materials
Canada
Products
SERVICE
HL2 TELEPHONE HANDSET LIFTER ACCESSORY

HARDWARE SETUP

C
FOR THE A20 TELEPHONE HEADSET AMPLIFIER
Snap the Lifter Motor Assembly with the A20 Adapter Housing
to the A20 accessory deck.
Connect the Adapter Power Plug to the aux jack of the A20
amplifier. The aux jack on the A20 amplifier is normally used for
the on line Indicator (OLI). If you plan to use the OLI, connect the
OLI plug to the Accessory Jack on the back side of the Lifter
Motor Assembly .
D
Route the associated wiring for the A20 amplifier through the
accessory deck as illustrated in the A20 User Guide.
Replace the A20 accessory deck lid and place your telephone on the
accessory deck.
Move and/or slide the Lifter Arm to a position near the top of the
earpiece of the telephone handset. Tighten the adjusting screw firmly
with a screw driver or small coin to prevent it from coming loose.
To test the Lifter, depress the handset/headset selector bar on the A20
amplifier and the Lifter Arm will automatically pick up your handset.
Push it again to have the unit return the telephone to its original
position.
You may need to manually readjust the lifter arm to the position shown
in .
D
Repeat this process until the Lifter can pick up and put down the
telephone handset without error.
No other connections are required. The Lifter will be powered
directly by the A20 amplifier.
You are now ready to make or receive calls.
LIFTER OPERATION
The handset/headset bar on the A20 amplifier will activate the lifter to
make or receive a call.
All Inc. Plantronics, 2003 Copyright
items including warranty, limited
our or dealer your contact Please
state from vary which rights other
specific you gives warranty This •
PLANTRONICS' IS THIS •
our contact please nformation,
(800) call Canada in and
U.S. the in service obtain To •
use may We warranty. the to
or repair option, our at will, We •
receipt. purchase nal
if only you to extends warranty This •
Products.
years two for lasts warranty This •
used and purchased were which
Products Commercial
in defects covers warranty This •
and US the in Purchased
Commercial Plantronics for
WARRANTY LIMITED
AND WARRANTY
C
D
A
D