Advertisement
SECTION 4 |
5
4=2Stage Type2
6
5=2Stage Type3
4.4.2.21.1 Programming Steps for Parameter "CHARGING PROFILE"
Enter Key
ð
A N Y O P E R A T I N G
M O D E
S C R E E N
4.4.2.22 BATTERY TYPE (Table 4.1, Parameter Setup Screen No. 22)
4.4.2.22.1 General Information
Parameter "BATTERY TYPE" is used to change the functionality of RJ-45 Jack marked "Battery Temp. Sensor" on the
front panel of EVO
[6, Fig 2.1 in the EVO
TM
Parameter Setup
1. Stage 1 – Bulk Stage (See Section 5.7.1.1 of the EVO
•
Charge at constant current = the programmed value of parameter "BULK
CURRENT"
(Default value is 40A. For details of programming range & procedure, refer to Section 4.4.2.1
•
Transition to Absorption Stage when voltage rises to the set value for programming
parameter "ABSORP VOLTAGE"
28.8V for EVO-2224/4024/2224E/4024E. For details of programming range & procedure, refer to Section
4.4.2.2
2. Stage 2 - Absorption Stage (See Section 5.7.2 of the EVO
details):
•
Charge at constant voltage = the programmed value for parameter "ABSORP
VOLTAGE".
(Default value is 14.4V for EVO-2212/3012/2212E/3012E and 28.8V for EVO-2224/4024/
2224E/4024E. For details of programming range & procedure, refer to Section 4.4.2.2)
•
Remain in Absorption Stage
•
Reset to Bulk Stage under the following conditions:
i.
If the AC input fails or is switched off and is restored subsequently
ii. If battery voltage falls to the programmed value of parameter "RESET TO
BULK" .
(Default value is 12.0V for EVO-2212/3012/2212E/3012E & 24.0V for EVO-2224/
4024/2224E/4024E
1. Stage 1 – Bulk Stage (See Section 5.7.1.1 of the EVO
•
Charge at constant current = the programmed value of parameter "BULK
CURRENT"
(Default value is 40A. For details of programming range & procedure, refer to Section 4.4.2.1
•
Transition to Absorption Stage when voltage rises to the set value for programming
parameter "ABSORP VOLTAGE"
28.8V for EVO-2224/4024/2224E/4024E. For details of programming range & procedure, refer to Section
4.4.2.2
2. Stage 2 - Absorption Stage (See Section 5.7.2 of the EVO
•
Charge at constant voltage = the programmed value for parameter "ABSORP
VOLTAGE".
(Default value is 14.4V for EVO-2212/3012/2212E/3012E and 28.8V for EVO-2224/4024/
2224E/4024E. For details of programming range & procedure, refer to Section 4.4.2.2)
•
Remain in Absorption Stage till the current reduces to value = the programmed
value of parameter "ABSORP EXIT AMPS"
range & procedure, refer to Section 4.4.2.20)
•
Switch off charging after the current reduces to value = the programmed value of
parameter "ABSORP EXIT AMPS"
procedure, refer to Section 4.4.2.20)
•
Reset to Bulk Stage under the following conditions:
i.
If the AC input fails or is switched off and is restored subsequently
ii. If battery voltage falls to the programmed value of parameter "RESET TO
BULK" .
(Default value is 12.0V for EVO-2212/3012/2212E/3012E & 24.0V for EVO-2224/4024/
.
2224E/4024E
For details of programming range & procedure, refer to Section 4.4.2.15).
Enter Key
ð
S E L E C T
G R O U P
B U L K C U R R E N T
C H A R G E
C U R V E
Owner's Manual]. The following 2 programming options are available:
TM
TM
(Default value is 14.4V for EVO-2212/3012/2212E/3012E and
.
For details of programming range & procedure, refer to Section 4.4.2.15).
TM
(Default value is 14.4V for EVO-2212/3012/2212E/3012E and
(Default value is 4A. For details of programming
(Default value is 4A. For details of programming range &
Up Key x 20 times
ð
C H A R G I N G P R O F I L E
4 0
A
0 = 3 S t g
A d a p t i v
Owner's Manual for details):
Owner's Manual for
TM
Owner's Manual for details):
Owner's Manual for details):
TM
Enter Key
ð
K E Y
I N
P A S S W O R D
0 0 0 0
Password 8052
See Section 4.3.1
− Lithium (See Section
5.11 of the EVO
TM
Owner's Manual for
details)
− Lithium (See Section
5.11 of the EVO
TM
Owner's Manual for
details)
− Nickel Zinc (See
Section 5.10 of the
EVO
Owner's Manual
TM
for details)
ð
C H A R G I N G P R O F I L E
0 = 3 S t g
A d a p t i v
See Table 4.1, Parameter
Setup Screen No.21 for
programming options
Advertisement
