Related Manuals for Pentair MNG4SD(X)
Summary of Contents for Pentair MNG4SD(X)
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP MNG4SD(X) MNG4HD (X) MNG6MD(X) INSTALLATION & OPERATION MANUAL pentair.com ©2022 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SPECIFICATIONS . - Page 3 PAGE INTENTIONALLY LEFT BLANK MY12716 (07-15-22)
-
Page 4: Safety Instructions
SAFETY INFORMATION SAFETY SYMBOLS GENERAL SAFETY Do not touch a pump while in operation as This is the safety alert symbol. When you see this symbol on they can operate at high temperatures. To avoid burns when your pump or in this manual, look for one of the following signal servicing the pump, shut off, allow it to cool for 30 minutes words and be alert to the potential for personal injury: after shutdown before handling. - Page 5 SAFETY INFORMATION ELECTRICAL SAFETY OTHER DANGERS RISK OF FIRE OR EXPLOSION. cause severe personal injury, property damage or death. Hazardous voltage. Can shock, burn, Do not smoke or use open flames in or around this system. or kill. When installing, operating, or servicing this pump, Do not pump flammable liquids.
-
Page 6: Specifications
GENERAL INFORMATION If the lower seal leaks and moisture enters this chamber, the This manual contains important information for the safe use of moisture will settle to the bottom of the chamber and will this product. Read completely and do not throw away. complete (significantly less than 330K ohms) the circuit between Reasonable care and safe methods should be practiced. - Page 7 GENERAL INFORMATION OVERLOAD HEATERS INSTALLING PUMP IN SUMP If the electrical panel is not used, starters with 3 leg overload relay must be supplied on 3 phase pumps. Each leg is to have an HAZARDOUS VOLTAGE. Can shock, burn, or kill. identical heater sized in accordance with the nameplate amps on When installing, operating, or servicing this pump, carefully the motor housing.
-
Page 8: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE Only a 230V pump from the factory is considered dual voltage, a cord label clearly states the factory wound voltage. ElECTROCUTION HAZARD: Must be installed by a qualified professional. Disconnect all electrical Remove all six (#7) cap screws then raise the cord cap power before installation or servicing the pump. -
Page 9: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance is products are to be used in a hazardous location applications per required. - Page 10 CONFIDENTIAL contains trade secrets and ASHLAND, OH. USA materials, compounds and other similar criteria are to be other proprietary information of Pentair strictly adhered to. No modifications allowed without Water. Duplication, disclosure or use are forbidden without the written consent of engineering approval.
-
Page 11: Troubleshooting
Lower float control may be hung-up in the closed position. Check in sump to be sure control is free. Selector switch may be in the Hand position. IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947. MY12716 (07-15-22) -
Page 12: Parts List
PARTS LIST MNG4SD(X), MNG4HD(X), MNG6MD(X) 4 POLE F28 F15 F3 F4 F26 A4 F27 E8 or E9 F28 F15 F15 F28 F26 B13 MY12716 (07-15-22) - Page 13 PARTS LIST ITEM PART DESCRIPTION PART # 4SD / 4HD / 6MD CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT ASSEMBLY SEE MOTOR PARTS GROUP SPACER SEE MOTOR PARTS GROUP OIL-MINERAL 153620017 BOLT-STATOR...
- Page 14 PARTS LIST HYDRAULIC ENDS PARTS LIST B7 F26 B11 F26 B3 F26 B11 F26 B3 F26 B11 F26 TYPICAL: GAP BETWEEN LINER(B15) AND IMPELLER(1) TO BE .008-.015" FROM FACTORY. ITEM DESCRIPTION PART # O-RING VOL COVER ** 05876A108 SCREW-HEX HEAD VOL COVER 002380301 SCREW-SOCKET HEAD CAP LINER BOLT 005560081...
- Page 15 PARTS LIST MOTOR PARTS LIST 25HP 25HP 30/40HP 30/40HP ITEM 2-POLE 3450 RPM 230/460/3/60 575/3/60 460/3/60 575/3/60 STATOR 27906D003 27906D603 27907D003 27907D603 ROTOR/SHAFT ASSEMBLY 27906D130 27906D130 27907D130 27907D130 OIL-MINERAL 153620017 (4 .8) 153620017 (4 .8) 153620017 (4 .25) 153620017 (4 .25) BOLT-STATOR 06106A027 (4) 06106A027 (4)
- Page 16 PARTS LIST IMPELLER PARTS LIST - MNG4HD(X) 1750 RPM CATALOG # PART # VOLTAGE/PH CORD TRIM IMPELLER # MNG4HD025403 28256E001 208/3 10 .75 154641142 MNG4HD025423 28256E002 230-460/3 10 .75 154641142 MNG4HD025443 28256E003 460/3 10 .75 154641142 MNG4HD025453 28256E004 575/3 10 .75 154641142 MNG4HDX025403 28256E601...
-
Page 17: Wiring Diagrams
WIRING DIAGRAMS MY12716 (07-15-22) - Page 18 WIRING DIAGRAMS MY12716 (07-15-22)
-
Page 19: Warranty
Warranty is effective only if Pentair Myers authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Myers will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Myers be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Myers service facility. - Page 20 Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice . Pentair is an equal opportunity employer .