Subscribe to Our Youtube Channel
Related Manuals for Pentair MNG3SC
Summary of Contents for Pentair MNG3SC
- Page 1 SUBMERSIBLE SOLIDS HANDLING PUMP MNG3SC(X), MNG4HC(X), MNG6MC(X) INSTALLATION & OPERATION MANUAL pentair.com ©2022 Pentair. All Rights Reserved.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . -
Page 3: Safety Instructions
SAFETY INFORMATION SAFETY SYMBOLS GENERAL SAFETY Do not touch a pump while in operation as This is the safety alert symbol. When you see this symbol on they can operate at high temperatures. To avoid burns when your pump or in this manual, look for one of the following signal servicing the pump, shut off, allow it to cool for 30 minutes words and be alert to the potential for personal injury: after shutdown before handling. - Page 4 SAFETY INFORMATION ELECTRICAL SAFETY OTHER DANGERS RISK OF FIRE OR EXPLOSION. cause severe personal injury, property damage or death. Hazardous voltage. Can shock, burn, Do not smoke or use open flames in or around this system. or kill. When installing, operating, or servicing this pump, Do not pump flammable liquids.
-
Page 5: Specifications
GENERAL INFORMATION If the lower seal leaks and moisture enters this chamber, the moisture would settle to the bottom of the chamber and will This manual contains important information for the safe use of complete (significantly less than 330K ohms) the circuit between this product. - Page 6 GENERAL INFORMATION OVERLOAD HEATERS INSTALLING PUMP IN SUMP If the electrical panel is not used, starters with 3 leg overload HAZARDOUS VOLTAGE. Can shock, burn, or kill. relay must be supplied on 3 phase pumps. Each leg is to have an When installing, operating, or servicing this pump, carefully identical heater sized in accordance with the nameplate amps on follow the safety instructions listed herein.
-
Page 7: Installation
INSTALLATION MAKING ELECTRICAL CONNECTIONS TO RE-WIRE THE PUMP FROM 230V TO 460V 3 PHASE Only a 230V pump from the factory is considered dual voltage, a cord label clearly states the factory wound voltage. ElECTROCUTION HAZARD: Must be Remove all six (#7) cap screws then raise the cord cap installed by a qualified professional. -
Page 8: Operation / Maintenance
OPERATIONS & MAINTENANCE PUMP MAINTENANCE RISK OF FIRE OR EXPLOSION. Do not smoke or use open flames in or around this system. Only the FM listed As the motors are oil filled, no lubrication or other maintenance is products are to be used in a hazardous location applications per required. - Page 9 ASHLAND, OH. USA CIRCLED DIMENSIONS ARE [XXX] DIMENSIONS IN mm materials, compounds and other similar criteria are to be other proprietary information of Pentair CRITICAL DIMENSIONS THAT NEED strictly adhered to. No modifications allowed without Water. Duplication, disclosure or use are TO BE INSPECTED.
-
Page 10: Troubleshooting
Check in sump to be sure control is free. Selector switch may be in the Hand position. IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION, OPERATION, MAINTENANCE OR TROUBLESHOOTING OF THE PUMP, PLEASE CALL PENTAIR AT 855-274-8947. MY12715 (07-15-22) -
Page 11: Parts List
PARTS LIST MNG3SC, MNG4HC, MNG6MC MY12715 (07-15-22) - Page 12 PARTS LIST ITEM PART DESCRIPTION PART # 4HC / 6MC CORD CAP 10-4 35' 152880315 CORD CAP 8-4 35' 152880325 CORD CAP 6-4 35' 152880335 STATOR SEE MOTOR PARTS GROUP ROTOR/SHAFT SEE MOTOR PARTS GROUP STATOR BOLT SHCS SEE MOTOR PARTS GROUP STATOR SPACER 007362141 153620017...
- Page 13 PART LIST HYDRAULIC ENDS B2 F26 B14 F26 B2 F26 B9 F26 B2 F26 B9 F26 TYPICAL: GAP BETWEEN LINER(B17) AND IMPELLER(1) TO BE SET AT .008-.015" FROM FACTORY ITEM DESCRIPTION KEY 3/8 X 1/4 SHAFT TO IMP ** / ++ 083460011 083460011 083460011...
- Page 14 ROTOR/SHAFT ASSEMBLY 27886D015 27886D015 27886D015 BOLT-STATOR (4) 06106A070 06106A070 06106A070 SPACER OIL-TRANSFORMER (1 .63) 153620017 153620017 153620017 IMPELLER PARTS LIST - MNG3SC (X) 3450 RPM CATALOG # ENGINEERING # VOLTAGE/PH CORD TRIM IMPELLER # MNG3SC015203 28251E021 208/3 6 .25 154371102 MNG3SC015223...
- Page 15 PARTS LIST IMPELLER PARTS LIST - MNG4HC (X) - 1750 RPM CATALOG # ENGINEERING # VOLTAGE/PH CORD TRIM ITEM #1 IMPELLER MNG4HC010403 28253E011 208/3 8 .75 154471222 MNG4HC010423 28253E012 230/460/3 8 .75 154471222 MNG4HC010443 28253E013 460/3 10-4 8 .75 154471222 MNG4HC010453 28253E014 575/3...
- Page 16 PARTS LIST IMPELLER PARTS LIST - MNG6MC (X) - 1750 RPM DESCRIPTION ENGINEERING # VOLTAGE/PH CORD TRIM ITEM #1 IMPELLER MNG6MC010403 28252E011 208/3 8 .13 154421152 MNG6MC010423 28252E012 230/460/3 8 .13 154421152 MNG6MC010443 28252E013 460/3 10-4 8 .13 154421152 MNG6MC010453 28252E014 575/3 10-4...
-
Page 17: Wiring Diagrams
WIRING DIAGRAMS MY12715 (07-15-22) - Page 18 WIRING DIAGRAMS MY12715 (07-15-22)
-
Page 19: Warranty
Warranty is effective only if Pentair Myers authorized control panels are used. All seal fail and heat sensing devices must be hooked up, functional and monitored or this warranty will be void. Pentair Myers will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Myers be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Myers service facility. - Page 20 Fx: 888.606.5484 All indicated Pentair trademarks and logos are property of Pentair . Third party registered and unregistered trademarks and logos are the property of their respective owners . Because we are continuously improving our products and services, Pentair reserves the right to change specifications without prior notice. Pentair is an equal opportunity employer.
Need help?
Do you have a question about the MNG3SC and is the answer not in the manual?
Questions and answers