Download Print this page
GE Evolve Troubleshooting & Repair Manual
GE Evolve Troubleshooting & Repair Manual

GE Evolve Troubleshooting & Repair Manual

Led area light scalable fixtures eas
Hide thumbs Also See for Evolve:

Advertisement

Quick Links

GE
Lighting
Evolve™ LED Area Light
Scalable Fixtures (EAS)
BEFORE YOU BEGIN
STOP
Read these instructions completely
and carefully. Save these instructions
for future use.
!
WARNING
Risk of electrical shock. Disconnect power before servicing
or installing product.
WARNING
!
Risk of injury or damage. Unit will fall if not installed properly.
Follow installation instructions.
!
CAUTION
Risk of injury. Wear safety glasses and gloves during
installation and servicing.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. This
Class [A] RFLD complies with the Canadian standard ICES-
003. Ce DEFR de la classe [ A ] est conforme à la NMB-003
du Canada.
Note: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required
to correct the interference at his own expense
Troubleshooting
and Repair Guide
• This luminaire is designed for outdoor lighting service, and
should not be used in areas of limited ventilation, or in high
ambient temperatures.
• Best results will be obtained if installed and maintained
according to the product's installation instructions. Refer to
installation instructions if reinstalling after repair.
• Refer to product installation instructions and product
datasheet for specifications and installation details.

Advertisement

loading

Summary of Contents for GE Evolve

  • Page 1 Lighting Troubleshooting and Repair Guide Evolve™ LED Area Light Scalable Fixtures (EAS) BEFORE YOU BEGIN STOP Read these instructions completely and carefully. Save these instructions for future use. WARNING Risk of electrical shock. Disconnect power before servicing or installing product.
  • Page 2 If power is required for testing, exercise caution to prevent risk of electric shock. NOTICE: GE disclaims any liability of injury or property damage resulting from the use of this trouble- shooting guide. Table of Contents...
  • Page 3: Section 1: Light Engine(S) Out

    Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 1: Light Engine(s) Out (continued) Power Door Captive Captive Screws Screws EASC Assembly LED Drivers Wiring Diagram LED Driver Light Engine input leads Cables Cables Left Light Engine...
  • Page 4 Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 1: Light Engine(s) Out (continued) Once power and wiring doors are open check electrical connections in this order. A. Make sure all incoming power leads are attached to the terminal board B.
  • Page 5 Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 1: Light Engine(s) Out (continued) Incoming leads to fixture Outgoing leads to fixture EASC Assembly View Pull back gently on leads. They should not disengage Pull back gently on leads.
  • Page 6 Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 1: Light Engine(s) Out (continued) C. Check leads from primary disconnect to drivers and surge protection device to ensure seated. EASA/EASB Assembly View Pull back gently on leads.
  • Page 7: Section 2: Day-Burning

    Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 2: Day-Burning When the Fixture will not shut off at daybreak when using a photocell controller, this is called a day burner. 1. Replace photocell controller with a new or known good Photocell.
  • Page 8 Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 3: Power Door Replacement (EASC) (continued) • Cut and strip input leads to Light Engine disconnect at the connectors. • Allow door to swing back and pivot and lift off of hinges...
  • Page 9 Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 3: Power Door Replacement (EASC) (continued) • Re-attach door in reverse order of removal. • Match up colors of leads from new door with fixture leads and assemble with provided quick connectors.
  • Page 10: Section 4: Power Door Replacement (Easa/Easb)

    Evolve™ LED Area Light Troubleshooting and Repair Guide Scalable Fixtures (EAS) Section 4: Power Door Replacement (EASA/EASB) • Disconnect and isolate incoming power to the fixture. • Separate both halves of the Primary disconnect. *Actual shape and color of connectors may vary.
  • Page 11 GE and the GE Monogram are trademarks of the General Electric Company. All other trademarks are the property of their respective owners. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.