Pioneer PDP-505HD Operating Instructions Manual page 45

To learn remote control signals
To operate other manufacturers' remote control signals
that cannot be preset using the remote control unit, have
the remote control unit learn these signals.
LED indicator
TV CBL
/VCR
/SAT
STANDBY/ON
1 2
SCREEN
MODE AUTO
POWER INPUT
AUDIO C C
1
4
7
¶
RETURN
CH
MUTING
RECEIVER
EDIT/ TV/SAT/DTV/DVD
2,5
LEARN
SOURCE
3
POWER
DVD SELECT
TOP MENU
MENU
FAVORITES
1 7
8 ¶
CU-PDP008
PLASMA DISPLAY REMOTE CONTROL UNIT
Example) To learn the operation to turn the VCR power
on.
1
Set the mode switch to TV/VCR (first position)
when a video cassette recorder is connected.
2
Simultaneously press LEARN and number button 2.
The LED indicator begins blinking.
3
Press SOURCE POWER to establish the target
operation.
The LED indicator remains lit.
Buttons which can be learned are as follows.
SOURCE POWER, CH (+), CH (–), 8, 1, 7, 3, ¡,
VCR
¶ (VCR REC)
CABLE SOURCE POWER, CH (+), CH (–), CH RETURN,
CH ENTER, 1 to 9, 0
SOURCE POWER, 2, 3, 5, ∞, SET/SELECT, CH (+),
SAT
CH (–), (SAT) INFO
SAT MENU, SAT GUIDE, CH ENTER, 1 to 9, 0
DTV SOURCE POWER, CH (+), CH (–), CH RETURN,
CH ENTER, 1 to 9, 0, •(dot), GREEN, RED, YELLOW,
2, 3, 5, ∞, SET/SELECT, DVT MENU, DTV GUIDE,
DTV INFO, DTV AUDIO, CC, CLEAR, VIEW MODE
SOURCE POWER, ¢, 4, 8, 1, 7, 3, ¡, 2,
DVD
3, 5, ∞, SET/SELECT, DVD MENU, DVD TOP
MENU
SOURCE POWER, ¢, 4, 8, 1, 7, 3, ¡
LD
÷ CABLE/SAT and DVD/LD cannot be selected at the same time.
÷ (SAT) INFO has no remote control signals preset.
1
DTV DVD
/LD
INPUT
3 4
STILL DISPLAY
RECEIVER DTV
VIEW
CLEAR MODE
2 3
5 6 2
8 9
0 CH
ENTER
CH
VOL
MENU
SAT/DTV
%
GUIDE
SET/
(SAT) /DTV
%
INFO
3 ¡
VCR REC
4 ¢
Î
O
4
Point the transmitters of both remote control
units toward each other with about 0.8 to 2.0 inch
(2 to 5 cm) between them, and press the POWER
button of the other manufacturer's remote control
unit.
0.8 to 2.0 inch (2 to 5 cm)
The LED indicator blinks.
÷ If the LED indicator blinks once, return to step 3 to
learn functions for other buttons.
÷ If the LED indicator flashes four times, it indicates
an error has occurred. Return to step 3 to redo the
learning.
÷ If the LED indicator flashes four times even after
having redone the learning, it means that the
learning capacity has reached its maximum.
5
When LEARN is pressed, the LEARN mode is
exited, and the remote control unit returns to
normal operation.
Notes
÷ To exit the LEARN mode during a learning operation, press
LEARN again.
÷ If the mode switch position is changed while in LEARN mode,
the LEARN mode is canceled.
÷ After steps 2 and 3, if you do not press a button for one
minute (no operation), the LEARN mode is canceled.
÷ There are some remote control signals which cannot be
learned.
To reset the LEARN setting
Have the LED blinking as in step 2 and then press and
hold the remote control unit's STANDBY/ON button
pressed for at least 2 seconds.
Note
It is necessary to reset the learn setting when you program the
remote control signal presets.
O D
PERATING THER EVICES
41
<ARE1349> En