Subscribe to Our Youtube Channel
Related Manuals for Norton Clipper CE414-350SS
Summary of Contents for Norton Clipper CE414-350SS
- Page 1 OWNER’S MANUAL HANDHELD ELECTRIC SAW Model: CE414-350SS Scan for a Digital copy of the Owner’s Manual REV 6/23 ...
-
Page 2: Warranty
In no event shall Norton Clipper be liable for consequential or incidental damages arising out of the failure of any product to operate properly. Integral units such as gasoline engines, electric motors, batteries, tires, transmissions, etc., are excluded from this warranty and are subject to the prime manufacturer's warranty. -
Page 3: Table Of Contents
PPE (Personal Protection Equipment) and Work Clothing ................8-9 KICKBACK AND RELATED WARNINGS ....................... 12-13 GENERAL DESCRIPTION ......................... 14-17 SPECFICATIONS ............................14 ITEMS INCLUDED WITH CE414-350SS ....................... 15 FUNCTIONAL FEATURES ..........................15-16 POWER TRIGGER USAGE ..........................17 ELECTRICAL SAFETY SYSTEM ........................17 ASSEMBLY ............................... -
Page 4: Safety Precautions Hazard Icons
SAFETY PRECAUTIONS Important warnings and pieces of advice are indicated on the machine with icons. HAZARD ICONS Danger! Failure to comply with the instructions could cause accidents with potentially life‐threatening injuries Caution! Failure to comply with the instructions could result in damage to the equipment or other material damage Carefully read the operating instructions. This applies before taking the equipment into operation and before any cleaning maintenance, or assembly work. Always wear the prescribed clothing. Always wear sturdy shoes with good grip. Wear safety gloves. This applies to all work with or on the equipment Before use, put on helmet, ear defenders and a visor. Switch off the motor! Noise level L = 100 dB(A). Never continue work with damaged cutting discs. ... - Page 5 SAFETY PRECAUTIONS Wear breathing protection. Do not use circular saw blades. Keep all guards in place when operating any piece of equipment Keep Hands, Feet, Hair, and Clothing way from all rotating parts. Never tamper with the governor components of settings to increase the maximum speed. Severe personal injury and damage to the motor or equipment can result if operated at speed above maximum. Always obey the maximum speed rating of blade. Do Not Lift the Saw By The Cutting Head or Blade Guard Important warnings and pieces of advice are indicated on the machine with icons. SAFETY ICONS Read OSHA and ANSI B7.1. Read operator’s instructions. Visit the industry safety page: www.safetyUAMA.org Eye protection must be worn.
-
Page 6: Silica And Dust Waring
SAFETY PRECAUTIONS DUST AND SILICA WARNING Grinding/cutting/drilling of masonry, concrete, metal, and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and other sources on... -
Page 7: Safety Warings
SAFETY PRECAUTIONS SAFETY WARNINGS This power tool must only be used to cut or shorten metals (hot cut) and mineral materials, such as concrete, masonry products (brick, block, pavers), with a diamond blade cutting blade approved for the material and only for the working situation indicated in Power Tool Usage: chapter Error! Reference source not found.. This power tool can be used for indoor or outdoor work. Use of this power tool for any other purpose, such as sawing of wood and to remove or grind off a material with the side surfaces of the blade is forbidden and is unsafe. Use of cutting tools, such as wood saw blades (which have a positive rake angle) or knives, must not be installed or used with this product. USE only Norton Clipper Diamond Blades that are designed for use with Electric Handheld Saws and the material being cut. For assistance with the correct Diamond Blade for use with your CE414‐350 contact customer service at 1‐800‐554‐ 8003. Using low quality blades or misapplication of the blade for the material being cut can cause any electrical saw to draw higher amperage and will over time result in any electrical motor damage which is not covered under warranty. Read all safety warnings and all instructions. Failure to follow the warnings and WARNING instructions may result in electric shock, fire and/or severe injury. Save all warnings and instructions for future reference. ... - Page 8 SAFETY SAFETY PRECAUTIONS PRECAUTIONS medication. A moment of inattention while operating power tools may result in serious personal injury. b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
-
Page 9: Ppe (Personal Protection Equipment) And Work Clothing
SAFETY PRECAUTIONS 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling, or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. - Page 10 SAFETY PRECAUTIONS Wear protective gloves with non-slip palms. Use approved respiratory protection meeting a minimum of N95 rating for dry cutting as protection from dust. Transport Before carrying or moving the power tool (even for short distances), always switch off the motor, wait until the cutting disc has stopped rotating, and disconnect the power supply.
- Page 11 SAFETY PRECAUTIONS When Starting Only use the power tool if it is in completely assembled condition. Hold the tool securely and firmly when starting. Always start up on level ground and securely hold the power tool. ...
- Page 12 SAFETY PRECAUTIONS present within 30 meters [approx. 30 yards] around the working area. Check the site of deployment for possible dangers. Spark formation during cutting means that work must never be performed close to potentially explosive due to shortages. ...
-
Page 13: Kickback And Related Warnings
SAFETY PRECAUTIONS Kickback and Related Warnings Kickback is a sudden reaction to a pinched or snagged rotating wheel. Pinching or snagging causes rapid stalling of the rotating wheel which in turn causes the uncontrolled power tool to be forced in the direction opposite of the wheel’s rotation at the point of the binding. For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. - Page 14 SAFETY PRECAUTIONS re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.
-
Page 15: General Description
GENERAL DESCRIPTION TECHNICAL DATE Model C414-350 Motor Brush Motor Horsepower Watts 3,100 Power Voltage Hertz GFCI IC Soft Start Thermal Overload Protection Electronic Clutch LED Indicator Lights Cord Length w/GFCI ft / m 9.8’ (3m) Spindle Diameter in / mm 0.787 (20mm) Spindle Diameter with Bushing in / mm... -
Page 16: Items Included With Ce414-350Ss
GENERAL DESCRIPTION ITEMS INCLUDED WITH CE414-350SS Machine CE414-350 Tool: Universal Wrench Air Filter (Pack of 6) Operating instructions FUCTIONAL FEATURES CE414-350SS Operator’s Front Left REV 06/23. - Page 17 GENERAL DESCRIPTION CE414-350SS Operator’s Rear Left 1. Cutting Blade 9.Trigger Assemble 2. Blade Guard 10. Carbon Brush Cover 3. Grip for Blade Guard Adjustment 11. Blade Shaft Screw 4. Top Handle 12. Power Cable 5. Water Hose 13. Water Hose to Coupling 6.
-
Page 18: Power Trigger Usage
GENERAL DESCRIPTION POWER TRIGGER USAGE Testing functionality of power trigger To test the power trigger, connect the machine to the correct power supply, grasp the handle to position your fingers next to the power trigger. Using the index finger and push to disengage the lock trigger (17), shown on the left. -
Page 19: Assembly
Blade Shaft Blot (Left Hand Thread) e. Universal Wrench a 14” Norton Clipper Diamond Blade 1 For blade installation, the power tool must be put securely on the ground and unplugged. With the power tool handle facing you place left arm on the power tool body and use the correlating hand to press the spindle lock button (7) shown below. - Page 20 ASSEMBLY 7 7 Rotating direction of the cutting disc Remove the blade bolt (d), its washer (c) and outer flange (b). Install the cutting disc (1), and make sure the bore of the disc slides onto the adapter (a) all the way. Also locate the rotational direction of the disk and match it with the diagram above’s note.
-
Page 21: Adjusting The Blade Guard
ASSEMBLY ADJUSTING THE BLADE GUARD Ensure that the machine is OFF, not running, and 2 4 remove the Spark Plug when making any adjustment. The blade guard shown on the left can be swivelled forward and backward in a limited area. -
Page 22: Water Connections
The CE414-350SS is only suitable for use with 115v/60 Hz/1 phase power and 20A circuit is recommended (using a 15A circuit can result in tripping the power source circuit breaker due to: pushing the tool too hard, using the incorrect blade for the material being cut, and/or from using too long and/or thin of gauge extension cord. - Page 23 GENERAL DESCRIPTION Power Connections and Extension Cords Extension cord with an electrical plug with 20-amp minimum capacity should be used. Connecting wires should be as short as possible, one piece of good condition, and suitable for outdoor usage. In no case should the connecting wires be longer than shown in the following table: Recommended Extension Cables...
- Page 24 ADA`PTE MEANS Figure: Outlet/Plug Grounding Generators: If a generator must be used, it must be the minimum size listed below or greater. The generator must have a 30A circuit and capable of providing a minimum of wattage at the required voltage. Under size generators will cause motor damage and is not covered under warranty.
-
Page 25: Operation
OPERATION OPERATIONAL CHECK LIST Always observe all safety instructions and all information in this document before using this machine! Check list for use (keywords only!) ......... Before start-up: Power tool in an operationally safe condition! ....Operating instructions complete ... -
Page 26: Blades
Take care that no body parts are in the path of the blade. Use Only Genuine Norton Clipper Diamond Blades For assistance with choosing the correct Norton Clipper Diamond Blade for your application call customer service at 1-800-554-8003... -
Page 27: Premissible Cutting Area And Danger From Kickback/Drawing Along
OPERATION PREMISSIBLE CUTTING AREA AND DANGER FROM KICKBACK/DRAWING ALONG The upper part of the blade must not be used for cutting! Only the lower part of the blade can be used for cutting! Danger of injury from kickback! Kickback results when the upper part of the blade is used for cutting. The power tool can be pushed towards the user's causing loss of operator control which can result in injury. -
Page 28: Cutting Technique
OPERATION CUTTING TECHNIQUE For complex cutting processes, cutting direction, and order of the cuts to be performed must be specified in advance to prevent clamping of the cutting blade by the moving debris or injury from dropping parts. ... -
Page 29: Cutting Concrete/Masonry Materials
Steps for Step Cutting with the CE414-350SS 1. Verify that the Diamond Blade being used is correct for the material being cut with the CE414- 350SS 2. - Page 30 11. Restart the water flow to the same rate as the previous cut. Adjust the flow rate as necessary. 12. Depress the CE414-350SS power trigger and allow the machine to get up to full speed 13. While keeping the blade perpendicular to the work surface slowly lower the Diamond Blade to the depth of 1”...
-
Page 31: Maintenance And Service
MAINTENANCE MAINTENANCE Maintenance, service, and repairs of all state‐of‐the‐art power tools must be done by a qualified service technician. Some maintenance, service and repairs may require specialized tools and training. We recommend all work to be performed by the Norton Clipper selling Distributor or Norton Clipper Authorized Service Center. We also recommend that all work not described in these operating instructions and all work you are not comfortable with be performed by the Norton Clipper selling Distributor or Norton Clipper Authorized Service Center. The Norton Clipper selling Distributor or Norton Clipper Authorized Service Center technicians have the required training, experience, and equipment and can make the most cost‐efficient solution available to you. He will advise and support you. For the nearest Norton Clipper selling Distributor or Norton Clipper Authorized Service Center please contact customer service at 1‐800‐554‐8003. Observe ALL safety instructions before beginning any maintenance, service, or repair work! After a run‐in time of approx. 5 operating hours, all screws and nuts that can be reached must be checked for tight fit and tightened again if required. safe It is best to keep the power tool in a dry and location when not in use. Do not allow the power tool motor, switch, or electrical connections to become wet. CLEANING AND CARE This power tool must be cleaned thoroughly after each workday and inspected for damage; in particular the cooling air openings around the brushes, power switch, and blade guard, material deposits will form over time (in particular when wet cutting), which may impair free rotation of the cutting disc. -
Page 32: Maintenance Schedule
MAINTENANCE MAINTENANCE SCHDULE Regular Service Period Preformed At Every Indicated Period → Whole Machine Inspect For Damaged or X X X X X X X Missing Components Clean X X Blade Collars Clean X Water Hose, Water Fittings, Clean X ... - Page 33 MAINTENANCE MAINTENANCE 2 4 Turn the top handle slightly counter clockwise h i 10 h Brush replacement: Disconnect the electrical supply. Loosen the two bolts (h) slightly on the top handle. Turn the top handle slightly counter clockwise as shown above to give the brush cover on the protective cowl (2) side of the power tool room for removal.
-
Page 34: Using The Kick Stand
USING THE KICK STAND 4 This power tool is packaged with a Kick Stand (8) retracted. With the one hand hold the tool by the top handle (4), if the saw has been used the cutting blade (1) should no longer be in motion, use your other hand to deploy the Kick 8 ... -
Page 35: Trouble Shooting
TROUBLE SHOOTING TROUBLE SHOOTING CE414-350SS will not start: 1. Verify Power is connected 2. Verify that power supply a. 20 AMP Minimum is recommended for best performance b. Verify that the Power Supply is Active i. If OFF check circuit breaker at the Power Supply. -
Page 36: Parts Breakdown
Web: www.nortonconstructionproducts.com NOTE: All Parts Are Sold as Individual (each) Unless Noted Otherwise Use Only Clipper Diamond Blades. Contact your local Norton Clipper Distributor or our Customer Service at 800-554-8003 for the best blade for the application. All parts are designated as either Service Parts (S) or Wear Parts (W) in the Type column in the parts listing. -
Page 37: Motor Assembly
PARTS BREAKDOWN MOTOR ASSEMBLY / ENSAMBLE DEL MOTOR / ASSEMBLAGE MOTEUR Motor Assembly / Ensamble del Motor / Assemblage Moteur POS UPC Description Descripción Description Type QTY NOTES Includes: Armature, Field CONJUNTO DE MOTOR ASSEMBLY ENSEMBLE MOTEUR Windings, Wave Washer, 1 S 1 70184633186 MOTORES CE414‐ CE414‐350SS CE414‐350SS Brushes, Brush Door 350SS Covers, w/Hardware CONJUNTO DE LA ENSEMBLE DE PORTE DE Brush doors set of 2 2 S ... -
Page 38: Blade Guard Assembly
PARTS BREAKDOWN BLADE GUARD ASSEMBLY / CONJUNTO DE PROTECCIÓN DE LA HOJA / ASSEMBLAGE DU PROTÈGE‐LAME Blade Guard Assembly / Conjunto de Protección de la Hoja / Assemblage du Protège‐Lame POS UPC Description Descripción Description Type QTY NOTES Includes: All hoses, fittings, clamps, and WATER HOSE KIT KIT MANGUERA AGUA valve assembled. DOES 1 W 1 70184633180 TUYAU D'EAU CE414‐350 NOT include Quick CE414‐350 CE414‐350 Detach Water FittingsC E414‐350‐005 KIT DE ADAPTADOR DE KIT D'ADAPTATEUR POUR Includes: Male and QD GARDEN HOSE 2 W 1 70184633184 MANGUERA DE TUYAU D'ARROSAGE QD Female Quick Detach ADAPTER KIT M+F ... -
Page 39: Forward Handle Assembly
PARTS BREAKDOWN FORWARD HANDLE ASSEMBLY / CONJUNTO DE MANIJA DELANTERA / ASSEMBLAGE DE LA POIGNÉE AVANT Forward Handle Assembly / Conjunto de Manija Delantera / Assemblage de la Poignée Avant POS UPC Description Descripción Description Type QTY NOTES Includes: Handle, Handle FORWARD HANDLE CONJUNTO DEL ENSEMBLE DE POIGNÉE Support, Kick Stand 1 W 1 70184633169 ASSEMBLY CE414‐ MANGO DELANTERO AVANT CE414‐350SS w/spring, and 350SS CE414‐350SS w/Hardware KICK STAND ASSEMBLY CONJUNTO DE ENSEMBLE BÉQUILLE Includes: Kick Stand 2 W 1 70184633170 CE414‐350SS SOPORTE CE414‐350SS ... -
Page 40: Gear Box Assembly
PARTS BREAKDOWN GEAR BOX ASSEMBLY / CONJUNTO DE CAJA DE CAMBIOS / ASSEMBLAGE DE LA BOITE DE VITESSES Gear Box Assembly / Conjunto de Caja de Cambios / Assemblage de la Boîte de Vitesses POS UPC Description Descripción Description Type QTY NOTES Includes (All items shown in the image): Blade Shaft Lock Assembly, GEAR BOX COMPLETE CAJA DE ENGRANAJES BOITE DE VITESSES Blade Shaft and Pinion 1 S 1 70184633167 ASSEMBLY CE414‐ CONJUNTO COMPLETO ENSEMBLE COMPLET Gear Assembly, Gear Box 350SS CE414‐350SS CE414‐350SS Housing w/Hardware, and Bearing and Shaft Kit Gear Box BLADE SHAFT and EJE DE LA HOJA y Includes: Blade Shaft ENSEMBLE ARBRE DE PINION GEAR CONJUNTO DEL ... - Page 41 PARTS BREAKDOWN GEAR BOX ASSEMBLY / CONJUNTO DE CAJA DE CAMBIOS / ASSEMBLAGE DE LA BOITE DE VITESSES POS UPC Description Descripción Description Type QTY NOTES Includes: Blade Shaft KIT DE BLOQUEO DEL BLADE SHAFT LOCK KIT KIT DE BLOCAGE D'ARBRE Lock, Spring, Blade Shaft 3 70184633176 S EJE DE LA HOJA CE414‐ CE414‐350SS DE LAME CE414‐350SS Lock Button, and two (2) 350SS O‐Rings KIT DE ALOJAMIENTO KIT DE LOGEMENT DE GEAR BOX HOUSING DE CAJA DE Includes: Gear Box BOÎTE DE VITESSES avec 4 S 1 70184633177 KIT w/HARDWARE ENGRANAJES CON Castings (Inner and ...
-
Page 42: Rear Handle Assembly
PARTS BREAKDOWN REAR HANDLE ASSEMBLY / MONTAJE DE LA MANIJA TRASERA / ASSEMBLAGE DE LA POIGNEE ARRIERE Rear Handle Assembly / Montaje de la Manija Trasera / Assemblage de la Poignée Arrière POS UPC Description Descripción Description Type QTY NOTES Includes: Cable Clamp CONJUNTO DE CABLE POWER CABLE ASSY CÂBLE D'ALIMENTATION w/Hardware, StrainRelief 1 70184633173 S 1 DE ALIMENTACIÓN con w/GFCI CE414‐350SS AVEC DDFT CE414‐350SS (2), Cable Gland, and GFCI CE414‐350SS Power Cable w/GFCI CONJUNTO DE REAR HANDLE ASSY POIGNEE ARRIERE CE414‐ Includes: Handle Left and 2 70184633171 S 1 MANGO TRASERO CE414‐350SS 350SS ... -
Page 43: Main Assembly
PARTS BREAKDOWN MAIN ASSEMBLY / ASAMBLEA PRINCIPAL / ASSEMBLAGE PRINCIPAL Main Assembly / Asamblea Principal / Assemblage Principal POS UPC Description Descripción Description Type QTY NOTES COLLAR SET CONJUNTO COLLAR JEU DE COLLIERS Includes Loose, Tight 1 70184633181 S 1 (LOOSE+INNER+ADP) (SUELTO+INTERIOR+ADP) (LÂCHE+INTÉRIEUR+ADP) Flange, and Blade Adapter CE414‐350SS CE414‐350SS CE414‐350SS USE ONLY NORTON CGHSTS1420 14” x CGHSTS1420 14” x .125 x CGHSTS1420 14” x .125 x DIAMOND BLADES. Use 2 W 70184684525 .125 x 1”/20mm 1”/20mm Cargador ... - Page 44 PARTS BREAKDOWN MAIN ASSEMBLY / ASAMBLEA PRINCIPAL / ASSEMBLAGE PRINCIPAL POS UPC Description Descripción Description Type QTY NOTES Montaje del Motor Assemblage du Moteur Page ‐NA‐ ‐NA‐ Motor Assembly Page 30 S See Page 30 for Details Página 30 30 5 70184680905 S 1 WRENCH UNIVERSAL LLAVE UNIVERSAL CLE UNIVERSELLE AIR FILTER 6 PACK PAQUETE DE 6 FILTROS FILTRE A AIR PACK DE 6 Air Filter 6 pack. NOT 6 W 1 70184633166 SOLD as EACH CE414‐350SS ...
- Page 45 NOTES This page is intentionally left blank. REV 06/23.
- Page 46 REV 06/23.
Need help?
Do you have a question about the CE414-350SS and is the answer not in the manual?
Questions and answers