Norton Clipper C1316SS Owner's Manual
  1. Manuals
  2. Brands
  3. Norton Clipper Manuals
  4. Saw
  5. C1316SS
  6. Owner's manual

Norton Clipper C1316SS Owner's Manual

Medium concrete saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Medium Concrete Saws
C1316SS
C1320SS
C1420SS
OWNERS
MANUAL
MODELS:
C1316SM
C1320SM
C1420SM
C2016SS
C2020SS
C2024SS
FORM C2020SS rev 7-2022

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C1316SS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Norton Clipper C1316SS

Summary of Contents for Norton Clipper C1316SS

  • Page 1 OWNERS MANUAL Medium Concrete Saws MODELS: C1316SS C1316SM C2016SS C1320SS C1320SM C2020SS C1420SS C1420SM C2024SS FORM C2020SS rev 7-2022...
  • Page 2 WARRANTY Saint-Gobain Abrasives, Inc. (Norton Clipper) warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of Saint-Gobain Abrasives, Inc. under this warranty is limited to replacement or repair of defective parts at Saint-Gobain Abrasives, Inc.

  • Page 3: Table Of Contents

    Table of Contents CONTENTS PAGE I. Preparation A. Safety Precautions B. Assembly C. Concrete Saw Specifications II. Operation A. Blade Installation 9-11 B. Changing the Blade Side 12-14 C. Engine Operation 14-15 D. Water Supply E. Controls 16-18 F. Operating The Saw 18-20 G.

  • Page 4: Preparation

    I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well ventilated, unoccupied areas approved, and away from sparks or flames. Don not fill the saw fuel tank while the engine is hot or running.
  • Page 5 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and NIOSH and...
  • Page 6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3.

  • Page 7: Assembly

    I. PREPARATION B. Assembly The self-propelled concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim.

  • Page 8: Concrete Saw Specifications

    C. C13xx/C20xx Concrete Saw Specifications C1316SS C1316SM C2016SS Dimensions/Weight C1320SS C1320SM C2020SS C2024SS Length (Transport) 56 inch (1142 mm) 56 inch (1142 mm) 56 inch (1142 mm) Width 26 inch (660 mm) 26 inch (600 mm) 26 inch (600 mm)

  • Page 9: Operation

    II. OPERATION Read and understand this manual before running or using the machine! A. Installing the Blade 1. Insure that the Ignition Power Key Switch is in the OFF position and then disconnect the spark plug. 2. Remove the blade shaft nut, (NOTE: Operator’s Right side is a left hand thread and the Operator’s Left side is right hand thread), and remove the outside collar.

  • Page 10: Blade Installation

    pin hole to insure both are round. If any problems are found do not use the blade. In addition check that the blade is the correct specification for the application. Use only Clipper Diamond Blades. This machine was not designed for the use with abrasive blades. 5.
  • Page 11 Observe rotation arrow on blade and do not exceed maximum RPM stamped on blade. NOTE: Organic bonded blades (A) must have a blotter. The blotter (B) must extend past the blade collar contact area as shown. Blades Use Only Norton Clipper Diamond Blades...

  • Page 12: Changing The Blade Side

    B. Changing the Blade Side: 1. Insure that the Ignition Power Key Switch is in the OFF position and then disconnect the spark plug. 2. Remove the blade shaft nut, (NOTE: Operator’s Right side is a left hand thread and the Operator’s Left side is right hand thread), and remove the outside collar.
  • Page 13 Blade Shaft Guard Blade Shaft Guard Removal 7. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. NOTE: Diamond blades are direction dependent so verify the direction of rotation of the blade. The machine will rotate the blade into the work surface (down cut).

  • Page 14: Engine Operation

    C. Engine Operation Prior to attempting to operate the engine, read the information contained in the engine owner's manual. An engine owner’s manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades.
  • Page 15 Turn the Fuel Control To the ON Position Move the choke lever to the CLOSED position. NOTE: do not use the choke if the engine is warm or the air temperature is high. Pull The Throttle Control Slightly to the Rear to provide some engine throttle.

  • Page 16: Water Supply

    D. Water Supply Pressurized source: Turn the water control to full "ON" when using wet cutting blades. The required flow rate is 4-6 gallons per minute. Optional Water Tank on saw: This supply is designed for use with dry blades to keep the dust levels down. The tank will not supply the proper water flow rates when used with wet cut only blades.
  • Page 17 Controls the cutting depth of the blade. Rotate Clockwise to raise and counter clockwise to lower the depth of cut. Fuel Tank (20 HP Only): An internal all metal fuel tank is standard equipment for 20 HP models only (C2016, C2020, C2024, PC2016, PC2020,and PC2024). All 13 HP models have a fuel tank attached to the top of the engine.

  • Page 18: Operating The Saw

    instructions for starting the engine found in the Engine manual. All 13 HP units are equipped with a Choke control attached to the Engine below the Air Cleaner on the Operator’s Right Hand Side. Engine Throttle: The Engine Throttle Control allows the operator to adjust the Engine Speed while starting and operating the machine.
  • Page 19 8. If wet cutting turn on the water supply at the source and then open the water valves on the saw. Make sure that there is a minimum of two gallons per minute of water flow!! 9. Be sure that the engine is running at full throttle!!! Check Engine Speed on the Tachometer to that listed on the Blade Speed Chart located on the Console is correct for the diameter of Blade being used.

  • Page 20: Cutting Technique

    15. To disengage the transmission, place the Speed Control in the Neutral position and then slide the Transmission Engage/Disengage lever fully to the “Disengage” position. Caution: Do Not Engage Or Disengage The Transmission While The Machine Is In The Forward Or Reverse Positions! G.

  • Page 21: Lead-Off Adjustment

     If the saw leads off excessively check the contact between the drive rollers and the rear wheels. Small steering corrections may be made by applying slight pressure to the right or left side of the handle bar. The drive rollers will need to be cleaned from time to time.

  • Page 22: Maintenance

    III. MAINTENANCE A. Engine Maintenance Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual.
  • Page 23 Honda 20HP Engines: The “Refer to Page” shown references in chart shown above is from the Honda Engine Manual. * = Replace the paper filter element only ** = Refer to the Shop Manual (1) Service more frequently when used in dusty areas (2) These items should be serviced by your Honda servicing dealer, unless you have the proper tools and are mechanically proficient.
  • Page 24 Only use a high-detergent, premium quality motor oil certified to meet or exceed U.S. automobile manufacturer’s requirements for Service Classification SG, SF/CC, CD. Motor oils will show the classification on the container. A SAE viscosity of 10W-30 is recommend by Honda for general, all temperature use. Please consult the below chart or contact your local Honda service center for the proper viscosity for your temperature range.
  • Page 25 Always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents.

  • Page 27: Bearings

    B. Bearings Re lubrication type bearings must be relubricated daily to assure long life. The grease used should conform to the NLGI grade two consistencies and be free of any chemical impurities such as free acid or free alkali, dust rust, metal particles or abrasives.

  • Page 28: V-Belts

    C. V-Belts Warning: Never make adjustments to belts or pulleys while engine is running! 1. The best tension for a belt drive is the lowest tension at which the belts will not slip under full load. 2. Simply take up the drive until the belts are snug in the grooves.

  • Page 29: Depth Control

    D. Depth Control The depth control (raising screw) consists of a threaded rod which feeds into a brass nut. In order to keep the two parts working smoothly it is necessary to keep the rod free from dirt and sludge as much as possible. Cleaning the threaded rod with a rag after each use will prevent sludge from collecting in the tube assembly and protect the threads.
  • Page 30 F. Self-Propelling System Raise Levantar Blade Speed Chart Tabla de Velocidad 3600 RPM Del Disco Blade Shaft Pulley Dia Eng Pulley Blade Shaft Eng rpm Lower Blade Dia Diámetro en Diameter Diametro de Flecha Disco Polea de Bajar Motor rpm Diámetro en Disco Flecha Disco RPM/Hours (RPM/Horas)
  • Page 31 7. Start and test the machine. 8. If any problems are found repeat steps 1 to7. Transmission Engage/Disengage Lever: Transmission Engage/Disengage lever has two (2) positions onto which it can be moved: Engaged position (Down) allows the transmission to operate the rear drive wheels by the means of rear wheel friction rollers, the Disengage position (Up) release the rear wheel friction rollers from the rear drive wheel (the saw can be “Free Wheeled”...
  • Page 32 G. ELECTRICAL DIAGRAM C1316SS & C1320SS: 13HP Manual Start Models Only Honda Engine Honda Part# 36100-ZE1-015 Kill SGA# 227115 Switch (BL) (BL) BL (238038) BL (238039) Oil Alert Transistorized Oil Level Unit Ignition Switch Spark Plug Unit...
  • Page 33 G. ELECTRICAL DIAGRAM C1316SM & C1320SM: 13HP Electric Start Models Only Circuit Rectifier G (238020) (GR) Breaker 15 Amp Change Honda Switch Fuse White Wire Ring Terminal To Female Bullet Kill Connector 0.156" Switch R (238031) (BL/R) (BL) R (238032) O (238033) BL (238035) Oil Alert...
  • Page 34 G. ELECTRICAL DIAGRAM C2016SS, C2020SS, C2024SS: 20HP Electric Start Models With Honda GX630TXF2...

  • Page 35: Parts List Section

    Any wear due to normal use of the machine will not be considered as a case of warranty for items designated as Wear Parts (W). For best performance and life Genuine Norton Clipper replacement parts should always be used. Changes to part specifications, are Order by UPC Number.
  • Page 36 C13xx and C20xx Frame Common...
  • Page 37 C13xxx and C20xx Frame Common Part No. Description Type 70184628065 LIFT FRAME 238171 70184628066 LIFT FRAME HOOK 238175 70184649901 SCR 3/8-16 X 1 1/4 HEX HD CAP 8041051 70184650149 WASHER 3/8 SPRING LOCK 8177012 70184650123 WASHER 3/8 SAE 8172009 70184628067 FRONT POINTER FRAME 238177 SCR 5/16-18 X 2 ½...
  • Page 38 C13xxx and C20xx Raise Axle...
  • Page 39 C13xx and C20xx Raise Axle Part No. Description Type 70184628082 RAISE AXLE MOUNT 238134 70184628085 REAR AXLE BUSHING 238129 70184628272 REAR WHEEL SPACER 238124 70184650129 WASHER 3/4 SAE 8172015 WHEEL 6 X 2 X 3/4 W/ROLLER BEARING 70184626921 238005 (REAR WHEEL SOLD EACH) WHEEL 5 X 2 X 3/4 W/ROLLER BEARING 238004 70184626920...
  • Page 40 C13xxx and C20xx Transmission...
  • Page 41 C13xxx and C20xx Transmission Part No. Description Type 70184678170 SPROCKET 35B12 X 17mm 229144 70184682129 SCR 1/4-20 X 1/4 SET CUP 407035 70184628053 ROLLER (1) 238150 70184650406 BEARING FLANGE 3/4 B 210071 70184628054 SPROCKET 35B48 X 34 B 238152 70184600718 MASTER LINK 238145 70184600717...
  • Page 42 C13xxx and C20xx Transmission Part No. Description Type 70184660324 BELT 3VX450(1) FOR 13 HP ONLY 109769 70184693853 BUSHING SPACER 238236 70184650144 WASHER 1/4 SPRING LOCK 8177010 70184694045 INTERNAL RETAINING RING 1 5/16" 237388 CONTROL LEVER PIN 238258 70184645806 TRANSMISSION CONTROL 232387 70184649904 SCR 3/8-16 X 2 HEX HD CAP...
  • Page 43 C13xxx and C20xx Blade Shaft & Engine Group 22 23...
  • Page 44 C13xxx and C20xx Blade Shaft & Engine Group Part No. Description Type 70184628084 BLADE SHAFT 238179 TIGHT COLLAR RIGHT SIDE 70184673904 227159 (LEFT HAND THREADS) TIGHT COLLAR LEFT SIDE 70184674352 227190 (RIGHT HAND THREADS) LOOSE COLLAR OUTER FLANGE 70184674082 227247 (INCLUDES DRIVE PIN) 70184673903 NUT BLADE SHAFT 3/4-16 LH...
  • Page 45 C13xxx and C20xx Blade Shaft & Engine Group Part No. Description Type 70184678162 SCR 1/2-13 X 4 FULL THREAD HEX HEAD CAP 229133 70184650358 NUT 1/2-13 JAM 8143005 70184649920 SCR 1/2-13 x 1-1/2 HEX HEAD CAP 8041096 70184650154 WASHER 1/2 SPRING LOCK 8177014 70184650124 WASHER 1/2 SAE...
  • Page 46 C13xxx and C20xx Blade Guard and Water System Group...
  • Page 47 C13xx and C20xx Blade Guard and Water System Group Part No. Description Type 70184659115 HOSE SWIVEL N1D0082 70184659097 WATER VALVE 1/2" N1C0021 70184626501 HOSE BARB 1/2" x ½”MPT 9602012 70184659232 HOSE CLAMP N1C0113 70184649879 SCR 1/4-20 X 1 HEX HD CAP 8041006 70184650120 WASHER 1/4 SAE...

  • Page 48: Controls And Console Group

    C13xxx and C20xx Controls and Console Group...
  • Page 49 C13xx and C20xx Controls and Console Group Part No. Description Type 70184627887 238120 HANDLE BAR 70184674393 227101 HANDLE BAR GRIP 70184649901 8041051 SCR 3/8-16 X 1 1/4 HEX HD CAP 70184650123 8172009 WASHER 3/8 SAE ZN PLT 70184650373 8160003 NUT 3/8-16 HEX LOCK 70184649879 8041006 SCR 1/4-20 X 1 HEX HD CAP...

  • Page 50: Depth Adjustment Group

    C13xxx and C20xx Depth Adjustment Group 19 21...
  • Page 51 C13xxx and C20xx Depth Adjustment Group Part No. Description Type 70184628181 DEPTH SCREW TUBE 238164 70184628182 GREASE ZERK 1/8 x 11/16 238234 70184682129 SCR 1/4-20 X 1/4 SET CUP 407035 70184628265 NUT 3/4-10 HEX HEAD 238163 70184628183 RAISE SCREW 238165 70184628274 DEPTH STOP BUSHING 238166...

  • Page 52: Optional Water Tank Group

    C13xxx and C20xx Optional Water Tank Group To Blade Guard Part No. Description Type 70184628014 WATER TANK KIT 238001 (Includes POS 1, and 3 to 12) -NA- 00310486962 WATER TANK W/CAP 00310486962 00310006560 CAP FOR WATER TANK 82794 70184628015 BRACKET FOR WATER TANK 238174 70184649901 SCR 3/8-16 UNC x 1-1/4 HEX HEAD CAP...
  • Page 53 NOTES...
  • Page 54 Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 254-918-2310 Fax: 254-918-2312...

This manual is also suitable for:

C1316smC2016ssC1320ssC1320smC2020ssC1420ss ... Show all

Table of Contents