Norton Clipper C914P Owner's Manual
  1. Manuals
  2. Brands
  3. Norton Clipper Manuals
  4. Saw
  5. C914P
  6. Owner's manual

Norton Clipper C914P Owner's Manual

Small concrete saw
Hide thumbs Also See for C914P:
Table of Contents

Advertisement

Quick Links

OWNERS
MANUAL
Small Concrete Saw
Models:
C914P
FORM: C914P rev 8-2020
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the C914P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Norton Clipper C914P

Summary of Contents for Norton Clipper C914P

  • Page 1 OWNERS MANUAL Small Concrete Saw Models: C914P FORM: C914P rev 8-2020...
  • Page 2 WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of Norton under this warranty is limited to replacement or repair of defective parts at Norton's Gainesville, Georgia factory, or at a point designated by it, of such part as shall appear to us upon inspection at such point, to have been defective in material or workmanship, with expense for transportation borne by the...

  • Page 3: Table Of Contents

    C. Water Supply 18-19 D. Operating The Saw 19-20 E. Cutting Technique III. Maintenance A. Engine 21-23 B. Wiring Diagram C914P 9 HP Honda C. Bearings D. V-Belts 25-32 Adjust The C914P Belt Tension 26-29- Belt Alignment Main Causes of Belt Failures E.

  • Page 4: Preparation

    I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well-ventilated, unoccupied approved areas, and away from sparks or flames.

  • Page 5: Dust And Silica Warning

    Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respiratory disease, cancer, birth defects or other reproductive harm. If you are unfamiliar with the risks associated with the particular process and/or material being cut or the composition of the tool being used, review the material safety data sheet and/or consult your employer, the material manufacturer/supplier, governmental agencies such as OSHA and...
  • Page 6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors should be cleaned and examined for damage before mounting the blade. 3.

  • Page 7: Assembly

    I. PREPARATION B. Assembly The C914P compact concrete saw is shipped completely assembled and ready for use except for Handle Bar, Diamond Blade, Gasoline, and Engine Oil. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim.
  • Page 8 Engine On/Off Switch Water Tank Quick Blade Guard Water Detach Fittings WYE and Nozzels ¾” Garden Hose Fitting Quick Detach Water Fitting with Valve Handle Bar Attachment Hardware Wrench and Wrench Holder Serial Number Plate Remove the saw from the pallet. Inspect the machine for concealed shipping damaged.
  • Page 9 Handle Bar Assembly Handle Bar Attachment Hardware Handle Bar Attachment Hardware Handle Bar Assembly Level the cutting frame and check the engine oil level and add if required (See Engine Manual) and add fuel (See Engine Manual). NOTE: Do not install the blade until it is time to use the saw.

  • Page 10: C914P Series Concrete Saw Specifications

    C. C914P Series Concrete Saw Specifications C914P Dimensions/Weight Length (Working) – in (mm) 57-55/64" (1,469) Length (Transport) – in (mm) 35-37/64" (929) Pointer Length – in (mm) 12-47/64" (323) Width – in (mm) 37-59/64" (963) Height – in (mm) 21-9/32" (541) Weight Created –...

  • Page 11: Engine Precautions

    D. Engine Precautions Prior to attempting to operate the engine, read the information contained in the engine owner's manual. An engine owner’s manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades.

  • Page 12: Operation

    II. OPERATION A. Blade Installation 1. Disconnect the spark plug. 2. Pull the Blade Guard Locking Pin Way from the Blade Guard and Pivot the Blade Guard out of the Way see Figure: Blade Guard Locking Pin for details. NOTE: The Blade Guard Locking Pin is under spring tension and will automatically move towards the Blade Guard, if it does not immediately replace the Blade Guard Locking Pin before using the saw.
  • Page 13 1” (25.4mm) and a maximum core thickness of 1/8” (3.1mm) see Figure: Blade Installation for details. NOTE: Maximum 14” (350mm) Blade can be used with the C914P, if the blade does not fit under the Blade Guard then the diameter is greater than 14” (350mm). ALL Diamond Blades have a direction of rotation indicated on the blade either, install the blade so that the direction of rotation is clock wise.
  • Page 14 7. Slide the outside blade shaft collar onto the blade shaft. The drive pin on the outside collar must project through the drive pin hole in the blade and into the inside collar. 8. Tighten the blade shaft nut (counter-clockwise) securely against the outside collar. See Figure: Blade Installed on C914P for details.
  • Page 15 Blade Installed on C914P 9. Lower the Blade Guard, verify that the Blade Guard Locking Pin Aligns with the Slot in the Blade Guard Bayonet and Reattach the Blade Guard Locking Pin by pushing the Locking Pin Towards the Blade Guard see Figure: Locking The Blade Guard for details.

  • Page 16: Starting The Engine

    Blade Guard Blade Guard Locking Pin Blade Bayonet Move Towards Blade Guard to LOCK Locking The Blade Guard 10. Reconnect the spark plug. One Revolution of the Hand Wheel equals ¼” (6.4mm) change of cut depth B. Starting the Engine 1.
  • Page 17 Move the choke lever to the CLOSED position. Turn the Fuel Control To the ON Position NOTE: The Choke may not be needed if the engine is warm or the air temperature is high. Move the Engine Throttle Slightly to the Left Turn the ON/OFF Switch to the ON position.

  • Page 18: Water Supply

    ON position. Never Transport a machine with the blade installed. C. Water Supply The C914P is designed for use with either a ¾” Garden Hose Fitting and pressurized water source or by using the included Water Tank. Water Tank Cap...

  • Page 19: Operating The Saw

    3. Follow ALL instructions under the Section “D. Operating The Saw” Water Tank source: The C914P included Water Tank is designed to provide some dust control for when a Pressurized Water source is not available. The Water Tank also increases the machine overall weight which assist at cutting at deeper depths.

  • Page 20: Cutting Technique

    1-1/2 to 2 inches until the desired depth of cut is reached this is known as Step Cutting. The C914P has a 4-5/8” (117.5mm) with a 14” (355.6mm) blade many blades that are marketed as a 14” blade are 350mm (13-3/4”) which will produce shallower cuts due to the overall diameter NOT...

  • Page 21: Maintenance

    III. MAINTENANCE A. Engine Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual.
  • Page 22 Always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents.
  • Page 23 B. Wiring Diagram C914P GX270 Honda...

  • Page 24: Bearings

    To adjust the C914P Belt Tension: The C914P uses a simple dual tensioning bolt system for the belt tensioning. The Belt Tensioning is made by two (2) pusher Screws which can be found in front of the Engine see Figure: C914P Belt Tensioning System for details.
  • Page 25 Tools Required: 17mm Open End Wrench 17mm Socket and Socket Wrench 1. Review the locations of the C914P Belt Tensioning system before proceeding. (See Figure: C914P Belt Tensioning System on the previous page). 2. Remove the Belt Guard by loosening and removing the two (2) M10 Acorn Nuts Belt Guard Retaining Hardware sets.
  • Page 26 Engine Pulley Engine Blade Drive Belts Engine Mounting Belt Guard Hardware one (1) Set Retaining per Corner of Engine Hardware Belt Tensioning Hardware Belt Tensioning Blade Shaft Hardware Pulley Belt Guard 3. Check belt tension by pushing up or down at the center top span of all three of the v-belts.
  • Page 27 5. Loosen the two (2) M10 Jam Nuts on the C914P Belt Tensioning with Assembly with a M17 Wrench (See Figure: C914P Belt Tensioning Hardware below). M10 Jam Nut M10 Jam Nut M10 x 80mm 1.5 Hex Head Cap Screw DIN933 Tensioning Bracket M10 x 80mm 1.5 Hex...

  • Page 28: Belt Alignment

    Check the belt tension frequently during the first day of operation. Check the belt tension periodically thereafter and make any necessary adjustments. Belt Alignment: 1. Review the locations of the C914P Belt Tensioning system before proceeding. (See Figure: C914P Belt Tensioning System on page 15).

  • Page 29: Main Causes Of Belt Failures

    Main Causes of Belt Failures: Premature Belt failure can be attributed to the following issues: Tension (too much or too little), Pulley Misalignment, Damaged Pulleys, Improper Handling or Storage, Incorrect Blade Specification for Material Being Cut, and Cutting Too Deep. Symptom Possible Cause Corrective Action...

  • Page 30: Depth Control

    E. Depth Control The depth control (raising screw) consists of a threaded rod, which feeds into a steel nut. In order to keep the two parts working smoothly it is necessary to keep the rod free from dirt and sludge as much as possible. Cleaning the threaded rod with a rag after each use will prevent sludge from collecting in the tube assembly and protect the threads.
  • Page 31 lubrication lithium base grease is recommended. When rotating the Hand Wheel and resistance is felt STOP rotating, over rotation can create great forces which can damage the Raise Screw Bearing housing. F. Inspections and Cleaning For long life and better machine performance follow the inspection and cleaning schedule below.

  • Page 32: Parts List Section

    3. Wherever alternate parts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, such as, parcel post, truck, UPS, FedEx, best way, etc. For the nearest Norton Clipper distributor call 254-918-2310 Common Replacement Parts Description NOTES...

  • Page 33: Depth Control Group

    Depth Control Group Grupo de Control de Profundidad Groupe de Contrôle de Profondeur...
  • Page 34 1  S  Nut Hand Wheel  Tuerca Rueda de Mano  Écrou Volant  Includes: Acorn Nut, and Washers  Includes:  Bearing   NOT Sold Separately  3  00310004907  Bearing Flange Kit  Kit de Brida de Rodamiento  Kit de Bride de Roulement  1  S  70184625649 SCR M10 X 40 1.5 DIN933 (2)  70184681610 WASHER M10 DIN125 (4)  70184628215 NUT M10 1.5 DIN985 LOCK (2)  Includes:  Raise Screw (Lifting)  Tornillo de Elevación C914P  Relever la vis (Levage)  4  70184609004  1  S  Raise Screw (1)  NOT Sold Separately  C914P/CS352  / CS352  C914P / CS352  KEY 6x6x25mm Square DIN 6880  Includes:  Raise Tube (1)  NOT Sold Separately  Levantar el Tubo C914P /  70184681616 Washer M12 DIN 125 Flat (2)  5  70184609005  1  S  Raise Tube C914P/CS352 ...

  • Page 35: Blade Guard Group

    Blade Guard Group / Protector de la Hoja Grupo / Groupe Blade Guard...
  • Page 36 Blade Guard Group / Protector de la Hoja Grupo / Groupe Blade Guard POS  UPC/Part  Description  Descripción  Description  QTY  Type  NOTES  Includes:  Blade Guard C914P (1)  NOT Sold Separately  70184681299 Water Hose (2)  70184628501 Ring Guard Lock (1)  70184628498 Guard Lock (1)  70184628499 Spring Guard Lock (1)  70184628500 Pin Guard Lock (1)  DECAL Rotational Direction (1)  Conjunto de Protector de  DECAL Risk of Cutting (1)  Blade Guard Assy With  Blade Guard Assy With  1  70184609019  Cuchilla Con Conexiones de  1  S  DECAL Blade Guard C914P/CS352 (1)  Water Connections ...

  • Page 37: Blade Shaft And Engine Group

    Blade Shaft and Engine Group Eje de Cuchilla y Grupo de Motores Groupe D'arbre de Pale et de Moteur...
  • Page 38 Washer M10 DIN125  Arandela M10 DIN125  Rondelle M10 DIN125  8  S  Sold Separately  4  70184628215  NUT M10 1.5 LOCK  Tuerca M10 1.5 Bloqueo  Ecrou M10 1.5 Verrou  4  S  Sold Separately  Includes  Kit Polea Motor  Kit Poulie Moteur  Pulley Eng 71mm x 1" 3VX 3G (1)  5  70184609006  PULLEY KIT ENG C914P  1  S  Set Screw M8x10 1.25 Cup Point (2)  C914P/CS352  C914P/CS352  70184649705 Key 1/4"x1‐1/2" (1)  Correa Trapezoidal PZ612  Courroie Trapézoïdale  6  70184609009  V‐Belt XPZ612 (3)  1  W  Belt XPZ612 (Set of 3)  (3)  XPZ612 (3)  Includes:  Pulley Kit Blade Shaft  Polea Kit Hoja Eje ...

  • Page 39: Main Frame And Pivoting Frame Group

    Main Frame and Pivoting Frame Group Cuadro Principal y Grupo de Cuadros Pivotantes Groupe de Châssis Principal et de Châssis Pivotant...
  • Page 40 Main Frame and Pivoting Frame Group Cuadro Principal y Grupo de Cuadros Pivotantes Groupe de Châssis Principal et de Châssis Pivotant POS  UPC/Part  Description  Descripción  Description  QTY  Type  NOTES  1  TBA  Frame C914P/CS352  Marco 914P / CS352  Cadre C914P / CS352  1  S  Main Frame With Decals ONLY  2  70184609013  Wrench Multiple  Llave Múltiple  Clé Multiple ...

  • Page 41: Belt Guard Group

    70184625642 NUT M10 1.5 DIN1587 Acorn (2)  70184681609 WASHER M10 DIN127 LOCK (2)  Guard Belt Assembly  Conjunto de Correa de  Ensemble de Ceinture de  1  TBA  1  S  70184600809 SCR M10 x 25 1.5 HEX HD CAP  C914P/CS352  Protección C914P/CS352  Protection C914P/CS352  DIN933 (2)  70184674633 DECAL CAUTION BLETS (1)  7018467632 DECAL CAUTION GUARDS (1)  DECAL CLIPPER (1)  70184674634 DECAL CAUTION DISCONNECT  (1)  Type: S = Service Part, W = Wear Part, All Parts Are Sold As Individual (each) Unless Noted Otherwise Kit Items Components are listed in the NOTES...

  • Page 42: Handle Bar Group

    Handle Bar Group / Grupo de Manillar / Groupe de Guidon POS  UPC/Part  Description  Descripción  Description  QTY  Type  NOTES  Includes:  Handle Bar Assembly  NOT Sold Separately  SCR M10 x 55 1.5 DIN933 (1)  Handle Bars Sup 1  TBA  1  S  Montaje de Manillar Sup Ensemble de Guidon Sup 70184681605 SCR M10 x 30 1.5 DIN933 (1)  Assembly 70184681615 NUT M10 Hex Jam (2)  NOTE:  Does NOT include Grips ...
  • Page 43 Pointer (Guide) Group / Grupo de Puntero (Guía) / Groupe Pointeur (Guide)  POS  UPC/Part  Description  Descripción  Description  QTY  Type  NOTES  Includes:  Front Pointer (Guide) NOT Sold Separately  Conjunto de Puntero Front Pointer (Guide) Ensemble Pointeur Avant 70184625649 SCR M10 X 40 1.5 DIN933 (1)  1  TBA  1  S  Delantero (Guía) C914 / Assembly C914/CS352 (Guide) C914 / CS352 70184681610 WASHER M10 DIN125 FLAT (2)  CS352 70184628215  NUT M10 1.5 DIN985 LOCK   (1)  Type: S = Service Part, W = Wear Part, All Parts Are Sold As Individual (each) Unless Noted Otherwise Kit Items Components are listed in the NOTES...

  • Page 44: Water Tank Group

    Water Tank Group / Grupo de Tanques de Agua / Groupe Réservoir D'eau...
  • Page 45 QTY  Type  NOTES  Includes:  Water Tank  1  00310351798  Water Tank Complete  Tanque de Augua Completo  Réservoir D'eau Complet  1  W  00310006560 Stopper (Cap)  NOTES: Water Tank Not Sold Separately  Includes  Hose 1/2OD x 3/8I x 38" NOT Sold  Kit de Protector de Cuchilla  Separately  Hose Blade Guard Kit  Kit de Protection de Lame  2  70184609015  de Manguera C914P /  1  W  70184674515 Clamp Hose Worm 7/32 to 5/8  C914P/CS352  de Tuyau C914P/CS352  x 5/16" Wd (1)  CS352  70184650463 Fitting Barb Hose 1/4" MPT x  3/8" Barb (1)  Includes:  Valve Assembly w/Hose Adapter (1) NOT  Sold Separately  Male Quick Detach x 3/4" Garden Hose (1)  Valve & Connector  Conjunto de Válvula y  Ensemble Valve et  NOT Sold Separately  3 ...

  • Page 46: Decals

    Decals / Etiqueta / Autocollant...
  • Page 47 POS  UPC/Part  Description  Descripción  Description  QTY  Type  NOTES  Includes:  Blade Guard:     DECAL Nose Stripes     DECAL Direction of Rotation      DECAL Risk of Cutting     DECAL Norton Clipper Blade Guard     DECAL Blade Failure     DECAL Saw Direction  Engine     DECAK Danger Lethal Fumes     DECAL Caution Guards     DECAL Caution Hot Surface  Belt Guard:  Kit de calcomanías C914P /     DECAL Caution Belts  ‐NA‐  TBA  Decal Kit C914P / CS352  Kit déco C914P / CS352  1  W     DECAL Norton Clipper Belt Guard  CS352     DECAL Caution Guards  Consolé     DECAL Model Number C914P Left and  Right Sides     DECAL 4 Pictogram     DECAL STOP     DECAL Caution Safety Gear     DECAL Blade Descent     DECAL Blade Rising ...
  • Page 48 Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 254-918-2310 Fax: 254-918-2312...

Table of Contents