Knox MEDVAULT Installation Manual
Hide thumbs
Also See for MEDVAULT:
- Hardware installation manual (12 pages) ,
- Hardware installation manual (11 pages)
Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Knox MEDVAULT
Summary of Contents for Knox MEDVAULT
- Page 1 MEDVAULT ® INSTALLATION GUIDE FOR UPGRADING MEDVAULT 2.0 TO V2.5...
-
Page 2: Restricted Rights Legend
INSTALLATION GUIDE Copyright® 2019 by the Knox Company. All rights reserved. The Knox® Company, the Knox logo and all other Knox Company product or service names are registered trademarks or trademarks of the Knox Company. 1601 W. Deer Valley Road, Phoenix, AZ 85027 Phone: 800-552-5669 •... - Page 3 • A retrofit kit suitable for your product version (shown below) • A note pad to record the board serial number and the serial number of the MedVault in which it was installed. NOTE: This information will be required to complete location identification, setup and initialization of each MedVault in KnoxConnect.
- Page 4 Before You Begin: • Remove contents and secure by other means if necessary • Use PIN or Override key to place MedVault in the OPEN state • Disconnect from power source and remote antenna (if any) WARNING: Always disconnect power to the MedVault before removing and installing circuit boards.
-
Page 5: Circuit Board Removal
CIRCUIT BOARD REMOVAL Step #1 Opening the MedVault • Use PIN or override key to unlock and open the MedVault door Step #2 Disconnect power and antenna connection from back panel • Remove the 2 screws from the service panel on the inside of the door •... - Page 6 INSTALLATION GUIDE Step #6 Unplug board power cable and remove WiFi board (if any) • If your MedVault is equipped with an antenna and WiFi networking, remove the WiFi board gently by rocking back and forth WiFi Board Step # 7 Disconnect Lead wires •...
- Page 7 Use a fine point wire cutter to snip the cable tie eyelet holding the wiring bundle taking care to prevent cutting or damage to the wires Snip and Remove Cable Tie Eyelet YOU ARE NOW READY TO INSTALL THE MEDVAULT 2.5 CIRCUIT BOARD 1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 800-552-5669 TECHSUPPORT@KNOXBOX.COM KNOXBOX.COM...
- Page 8 Gently push down on the black tab to secure connector Keypad Display Ethernet IO Connector Connection Keyboard display connection in open position 1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 800-552-5669 TECHSUPPORT@KNOXBOX.COM KNOXBOX.COM PAGE 8 ©Knox Company. All rights reserved. OPE-MVUSER-0473-D...
- Page 9 1. Ensure the wires are installed in the correct position in the terminal block. Black Ground Wire Red Power Wire Yellow Light Wire 1601 W. DEER VALLEY RD. PHOENIX, AZ 85027 800-552-5669 TECHSUPPORT@KNOXBOX.COM KNOXBOX.COM PAGE 9 ©Knox Company. All rights reserved. OPE-MVUSER-0473-D...
- Page 10 Step 16 Secure Reset Switch wire • The MedVault 2.5 is equipped with an electronic reset. The reset switch wire will not be reconnected. Using the cable tie supplied in the retrofit kit, secure the white reset switch wire as shown...
- Page 11 INSTALLATION GUIDE INITIALIZING MEDVAULT 2.5 IN KNOXCONNECT In order to resume use of your MedVault, you must establish users, user PINs, and device settings for your MedVault in KnoxConnect. Please refer to the Knox Networking Guide and KnoxConnect Admin Guide to complete this setup before continuing.
- Page 12 To view MedVault 2.5 Retrofit Kit installation, click on the YouTube Link below: https://www.youtube.com/watch?v=uGWdvA0tzu0&t=6s To view KnoxConnect Admin Guide or KnoxConnect Networking Guide, log into the Knox Fire Department Portal or contact your department’s KnoxConnect Administrator Questions? Contact Technical Support at 800.552.5669...
Need help?
Do you have a question about the MEDVAULT and is the answer not in the manual?
Questions and answers