Page 2
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com...
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation.
Page 4
C. Mounting Nut D. Mounting Screws 6. Spray hose 7. Weight 8. Hex Wrench 9. Base O-Ring For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: Toll-Free: 800-775-0703 or customerservice@kraususa.com...
Page 5
Faucet Installation Procedure 11 1/4" (284.7mm) 3 3/4" (94.6mm) 1 1/8" (30mm) 12° 9 1/8" (231.5mm) MAX. 1 3/8" (35mm) Ø 1 3/8" (35mm) Installer Tip: Shut off main water supply before installing new faucet.
Page 6
Step 1A. Faucet installation - with deck plate For three-hole installation: Deck plate, base plate and silicone sealant (optional) are required. Note: Optional deck plate not included. Step 1B. Faucet installation - without deck plate For single-hole installation: Deck plate, base plate and silicone sealant are NOT required.
Page 7
Step 2. Install faucet and mounting hardware Insert faucet body (2) into hole in countertop or deck plate assembly. Install mounting hardware (5A, B, C & D) from underneath the countertop. Step 3. Secure mounting hardware Adjust direction of faucet body (2) so that handle is on right side of faucet.
Page 8
Step 4. Attach spray hose and counterweight Connect spray hose (7) to quick connector (4) attached to supply line. Install weight (8) on lowest vertical point on spray hose (7). Step 5. Connect waterlines Connect waterlines (3) to angle stops. Tighten both ends of waterlines with a wrench until snug.
Page 9
Step 6. Flush spray hose Remove spray head (1) from spray hose (7). Hold tip of spray hose (7). Turn faucet on and let the water run for 60 seconds to flush any debris. Step 7. Check for leaks Check for leaks at the connections.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Locking nut has come loose or Remove button located at top of handle. Leakage under faucet handle cartridge needs to be reseated.
Page 12
Maintenance - Cartridge Replacement Step 1: Remove button located at the top of the handle. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand. Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge.
Page 13
(5) years from the date of purchase. Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus.
Page 14
12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com...
Page 15
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...