Related Manuals for AS MOTOR AS 65/2T Enduro-Kat
Summary of Contents for AS MOTOR AS 65/2T Enduro-Kat
- Page 1 Operating Instructions Allmäher® AS 65/2T Enduro-Kat From serial number: 019910020001 Issued: 15 April 2013, V11.0 EN-Translation of the Original Operating Instructions...
-
Page 2: Preface
dummy Preface Intended use The device is exclusively intended for cutting Please fill in all data referring to your device. When ordering spare parts, provide your deal- grass or similar vegetation in well maintained er with the device and engine number. areas in agriculture, forestry, and landscape conservation that are mowed at least once a Serial number:... -
Page 3: Table Of Contents
Contents Maintenance and cleaning ...... 17 Preface ............. dummy Preparations .......... 18 Intended use ..........Cleaning the device ....... 18 General inspection ......... 19 Explanation of the symbols ....dummy Inhalts verz eichnis Chain lubrication ........19 Symbols in the instructions ....Transmission ......... -
Page 4: Explanation Of The Symbols
dummy Inhalts verz eichnis Explanation of the symbols Prior to any repair and mainte- nance work, pull off the spark plug connector. Symbols in the instructions In these operating instructions, the following symbols are used to denote special dangers. Warning. These symbols denote special Clean the ventilation grid! dangers. -
Page 5: Safety Instructions
Use gloves and avoid skin Safety instructions contact with the fuel. Get informed! For your safety, read these operating instruc- Fuel up outdoors only when the engine is cool tions with care. Familiarize yourself with the and not running. Use a filler or funnel. control elements and the proper use of the Do not spill any fuel and do not let the fuel get device. -
Page 6: Use Caution During Operation
Do not remove, change or override any safety Prior to mowing devices or control elements. Personal protective measures Observe the maintenance instructions and replace damaged or worn parts immediately. While mowing, always wear sturdy footwear with good grip, Have an authorised service centre check your long trousers, and gloves. -
Page 7: When Work Is Completed
– If side inclination is too great, fuel may leak Be extremely cautious when turning the device from the carburetor or the tank. This poses a round or pulling it toward you and when mov- fire hazard! ing in reverse. –... - Page 8 – the repair work was not carried out by an authorised service station. The same applies for spare parts and accesso- ries.
-
Page 9: Device Description
Device description 18 17 Steerable front wheel Interlock steerable front wheel Cutting height adjustment Ventilation grid Starter grip Air filter Lever for lateral adjustment of handlebar Handlebar console Height adjustment of handlebar 10 Type plate 11 Switching lever 12 Tank ventilation 13 Tank filler spout 14 Fuel valve 15 Spark plug connector... -
Page 10: Control Elements
Engine stop switch (5) Control elements Switch the ignition on and off with the engine stop switch. When you switch off the ignition, the engine is switched off. 0: OFF I: ON Throttle lever (1) With the accelerator lever, you change the Lever for lateral adjustment of handlebar (4) engine speed and thus control the engine 1. -
Page 11: Assembly
Fuel valve Switching lever The transmission has 5 forwards gears, neutral position, and one reverse gear. For switching, 1: Open release the drive lever, switch to the next gear 2: Closed and continue to drive. Assembly Scope of delivery Driving in reverse 2.1 km/h The device is delivered in a carton. -
Page 12: Guide Bar And Handlebar
– can carry the empty weight of the de- Guide bar and handlebar vice + 100 kg. – are wider than the device. – have a slip-free surface. 1. Put the device in front of the ramps and make sure that the ramps –... -
Page 13: Information On Mowing
2. Drive the device carefully down the ramps Prior to starting of the platform. Fuel leer er Abs atz Information on mowing Use a mixture of two stroke oil and unleaded petrol (octane rating at least ROZ 91). You can Prior to mowing, check your device for com- use E10 petrol. -
Page 14: Tanking Up
2. Pull the lever (1) upwards and turn it until Tanking up the desired cutting height is reached. Locking steerable front wheel Danger! Fuel is ignited by hot engine parts. On flat terrain, it is more comfortable to leave Prior to filling up, switch off the the front wheel free to pivot. -
Page 15: Engaging The Blade
2. Open the fuel valve and the tank ventila- Adjusting the driving speed: tion. The driving speed depends on the quantity and 3. Plug on the spark plug connector. thickness of the growth. If the growth is espe- cially high and thick, you can mow at low 4. -
Page 16: Differential Lock
5. Hold back the handlebar and the inner Switching off and parking wheel. 6. Switch the differential lock back on. The drive prevents sliding and supports the Caution! turn manoeuvre. On a slope, the device can roll away. Differential lock Put the device on even ground only The differential lock connects the rear wheels or secure it against rolling away. -
Page 17: Maintenance And Cleaning
Maintenance and cleaning warranty. Operational safety is endangered as Regular maintenance keeps your device ready well. for use. Contact your authorised service centre for If you do not observe the maintenance notices, checkup if you detect problems during mainte- faults may occur that are not covered by the nance. -
Page 18: Preparations
Component Action Maintenance interval □ ▲ Acceleration Check for proper function. lever ■ ▲ Chassis and Check for rust and fissures and check the welding seams. impact pro- ■ ▲ Are all protective device fastened correctly and properly func- tection tioning? ■... -
Page 19: General Inspection
Fire hazard! Pay special attention so that Maintaining the engine components at the silencer are clean. For cleaning use a hand brush. Remove stub- Danger! born soiling with a wooden or plastic spatula. If the speed of rotation is set too Clean the outer housing parts with a cloth. -
Page 20: Checking The Drive
4. Actuate the drive lever. Caution! A cleaning of the air filter with 5. Try to pull the device backwards. compressed air damages the filter If the rear wheels lock, the drive is correctly fabric and the air filter becomes adjusted. -
Page 21: Checking The Blade
Blade change Checking the blade Danger! Improperly mounted and main- tained blades pose a severe injury hazard. Work at the blade shall only be performed by an authorised service centre. Wear sturdy gloves when you check the blades. It is absolutely necessary to change the blade: –... -
Page 22: Longer Storage
Longer storage Wear parts 1. Observe the safety instructions regarding Some parts are wear parts. They wear during the handling of fuel. use and must be replaced. The warranty does 2. Draining fuel tank: Put a piece of a tube on not cover the following parts: the fuel valve and fill the fuel in an ade- Blades, cutting blades, cutter bars, blade bolts,... - Page 23 Preserve the proof of purchase or the warranty card that was filled out by the vendor.
-
Page 24: Troubleshooting
Troubleshooting You can find an authorised service centre on The following table contains the most frequent our home page www.as-motor.dewww.as- problems and their elimination. If more prob- motor.de. lems occur, contact the closest authorised service centre. Problem Possible cause Remedy Engine does not Engine stop switch is set to Switch the engine stop switch to ON. - Page 25 Problem Possible cause Remedy Spark plug is sooted, dam- Clean spark plug and check electrode aged, or incorrect electrode gap (see also Maintenance and gap. cleaning). If necessary, replace spark plug. Housing of mower is jammed. See also Maintenance and cleaning. No drive when drive Driving belt is insufficiently Authorised service centre.
- Page 26 Problem Possible cause Remedy Mulching result with Plant material is ejected too Increase speed. low plant material quickly. not satisfactory Discharge channel Mowed grass was too long or Adjust cutting height and mowing is jammed too damp. speed to the mowing conditions. Blade is worn.
-
Page 27: Mixing Ratios Fuel
Mixing ratios fuel Petrol Two-stroke oil Only with Titan 2T 100S 1:50 1:100 (octane number at least ROZ Litre Litre (=ml/cm Litre (=ml/cm 0.02 (20) 0.01 (10) 0.04 (40) 0.02 (20) 0.06 (60) 0.03 (30) 0.08 (80) 0.04 (40) 0.1 (100) 0.05 (50) 0.2 (200) 0.1 (100) -
Page 28: Technical Data
Technical data Type AS 65/2T Enduro-Kat 0 – 30 °C Range of application (temperature) Engine, type One cylinder two stroke engine with catalyser Manufacturer AS-Motor Germany Type AS 165 Kat Cylinder capacity 165cm Performance 4.4kW (6 PS) Engine speed 4500 min... -
Page 29: Declaration Of Conformity
Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de Declaration of conformity We declare that the lawnmower type AS 65/2T Enduro-Kat with serial number starting from 019910020001 as brought into circulation by us conforms to all relevant 2006/42/EG safety and health requirements of the EC directives 2004/108/EG listed. - Page 30 Umbruc h...
- Page 31 Umbruc h...
- Page 32 Mar keti ng Umbruc h AS-Motor Germany GmbH & Co. KG Ellwanger Straße 15 D-74424 Bühlertann www.as-motor.de Professional technology for gardens and landscapes Allmäher® Manoeuvrable meadow mower for extensive green area care. The Allmäher reliably shreds metre-high grass, undergrowth, and weeds.
Need help?
Do you have a question about the AS 65/2T Enduro-Kat and is the answer not in the manual?
Questions and answers