Advertisement
Quick Links
Table Of Contents:
Wire Harnesses Quick View
11 Pin Accessory Input/Output Connector
2 Pin LED / Valet Connectors
3 Pin Door Lock/Unlock Connector & Wiring
Dome Delay Learning Proceedure
Wire Dressing and Operation Explanation
Programming Transmitters
Programming Alarm Feature Bank 2
Circuit Wiring Layout
Rev B: New Format
PATENTED: www.voxxintl.com/company/patents
Page 1
Model APS-510C
Installation Manual
Remote Control Vehicle
Security System
Page 2
Page 3
Page 4
Page 5 - 6
Page 6
Page 8
Page 8 - 10
Page 10
Page 10
Page 10
Page 10
Page 10
Page 11
Page 11
Page 12
128-8806b
1 of 12
Advertisement
Related Manuals for Audiovox Prestige Platinum Plus APS-510C
Summary of Contents for Audiovox Prestige Platinum Plus APS-510C
-
Page 1: Table Of Contents
Model APS-510C Installation Manual Remote Control Vehicle Security System Table Of Contents: Before You Begin Page 2 Wire Harnesses Quick View Page 3 Mounting Of The Major Components Page 4 8 Pin Power Connector Page 5 - 6 11 Pin Accessory Input/Output Connector Page 6 2 Pin LED / Valet Connectors Page 8... -
Page 2: Before You Begin
Before You Begin PROFESSIONAL INSTALLATION IS STRONGLY RECOMMENDED Roll down window to avoid locking the keys in the vehicle during installation. Avoid mounting components or routing wires near hot surfaces or near moving parts like the steering wheel as it may prevent proper operation of the vehicle. Tape or loom wires under the hood and dash for protection as well appearance. - Page 3 11 Pin Main Wiring Harness Part # 1122916 Green / Black Channel 4 Output (-) 300mA Blue / Black Alternate Channel 3 Output (-) 300mA Black / White Horn Output (-) 300mA Orange / White Gnd. Output When Disarmed (-) 300mA Dark Green Negative Hood / Trunk Trigger Input Brown...
-
Page 4: Mounting Of The Major Components
MOUNTING OF THE MAJOR COMPONENTS Control Module: Part # 1362302 Select a mounting location inside the passenger compartment ( up behind the dash ) and secure using the two screws provided. The control module can also be secured in place using cable ties. Do Not mount the control module in the engine compartment, as it is not waterproof. -
Page 5: Pin Power Connector
Note: This is a normally closed starter cut arrangement and when power is removed from the security system, the starter disable feature will not operate, allowing the vehicle to start. Audiovox does not recommend using the Orange wire to interrupt anything but the starting circuit of the vehicle. - Page 6 Note: This is a normally opened starter cut arrangement, and when power is removed from the security system, the starter disable feature will remain operational, and the vehicle will not start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt anything but the starting circuit of the vehicle.
- Page 7 Dark Green Wire: ( - ) Instant Trigger Zone This is an instant on ground trigger wire. It must be connected to the optional previously installed hood and trunk pin switches when used. Brown Wire: - Door Trigger If the vehicle’s courtesy light switches have a ( - ) ground output when the door is opened (GM and most Imports), you must connect this wire to the negative output from one of the door switches.
- Page 8 WARNING: Connecting the light blue/green to the high current switched output of trunk release circuits, some remote start trigger inputs, will damage the control module. Connect the light blue/green to terminal 86 of a 30 A automotive relay, connect terminal 85 to a + 12 volt source, and wire the remaining relay contacts to perform the selected function of channel 5.
-
Page 9: Pin Upgrade Telematic Module
These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159a Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. -
Page 10: Completing The Installation
NOTE: If using the TWO WAY Telematic module, only Ground, TX, and RX are used on this port, the + 12volt supply for the two way module must be sourced separately or the unit will not operate. COMPLETING THE INSTALLATION NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. - Page 11 PROGRAMMING BANK 1 (TRANSMITTERS): 1) Turn the ignition key to the on position. 2) Press and release the valet/programming switch 3 times (Siren Chirps). 3 Press the Lock Button of each transmitter you want programmed until you hear a chirp from the horn or siren. 4) Turn the ignition switch off.
- Page 12 For technical support go to www.prestigecarsecurity.com or call 1 800 225 6074. © 2013 Audiovox Electronics Corp., Hauppauge, N.Y. 11788 128-8806b Page 12 128-8806b 12 of 12...