Mitsubishi Electric LGH-15RVX3-E Installation Instructions Manual page 24

No.36
Outdoor temperature display setting
Set to display outdoor temperature detected by Lossnay unit
thermistor.
This function is N/A from Lossnay unit DIP-SW.
This function is available only when "Sensor value" is set to "Yes"
(Display) by the remote controller PZ-62DR-EA/EB.
DIP-SW PZ-62DR-EA/EB Setting
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 36
- -
No.37
Indoor temperature display setting
Set to display indoor temperature detected by Lossnay unit thermistor.
This function is N/A from Lossnay unit DIP-SW.
This function is available only when "Sensor value" is set to "Yes"
(Display) by the remote controller PZ-62DR-EA/EB.
DIP-SW PZ-62DR-EA/EB Setting
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 37
- -
No.38
CO concentration display setting
2
Set to display CO concentration when the CO
2
PZ-70CSW-E) is used.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-EA/EB Setting
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 38
- -
- This function is available only when "Sensor value" is set to "Yes"
(Display) by the remote controller PZ-62DR-EA/EB.
- When displaying CO concentration, supply air temperature cannot
2
be displayed simultaneously.
- CO concentration display shows the value detected by a CO
2
sensor connected to Lossnay unit. The value may differ from the
actual indoor CO concentration. This function cannot be used as a
2
measuring instrument.
- The value may significantly differ from the actual indoor CO
concentration for approx. 15 minutes after starting operation.
- When 3rd party's CO sensor is connected, CO
2
displayed on PZ-62DR-EA/EB screen.
No.39
Calculated supply air temperature display
setting
Set to display calculated supply air temperature or not.
This function is N/A from Lossnay unit DIP-SW.
In addition, this function is available only when "Sensor value" is set to
"Yes"(Display) by the remote controller PZ-62DR-EA/EB.
CO concentration and supply air temperature can not be displayed at
2
the same time.
DIP-SW PZ-62DR-EA/EB Setting
Setting
check
SW No. Setting Function No. Setting Data
- -
N/A 39
- -
- CO concentration and supply air temperature can not be displayed
2
at the same time.
Outdoor temperature
check display
0 N/A
1 Available on the screen
(Factory setting)
of PZ-62DR-EA/EB
Indoor temperature
check display
0 N/A
Available on the screen
1
(Factory setting)
of PZ-62DR-EA/EB
sensor (PZ-70CSD-E,
2
CO concentration
2
check display
0 N/A
1 Available on the screen
(Factory setting)
of PZ-62DR-EA/EB
2
concentration is not
2
Calculated supply air
check temperature display
0
N/A
(Factory setting)
Available on the screen
1
of PZ-62DR-EA/EB
No.40, 41
Set the 10 digit of temperature exchange efficiency which is used to
calculate supply air temperature.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
-
N/A -
-
-
-
-
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
N/A -
-
-
-
-
-
No.42
Outdoor temperature correction
Set the correction for the outdoor temperature displayed on the
PZ-62DR-EA/EB screen by function
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
SW No. Setting
-
-
-
-
-
2 -
-
N/A -
-
-
-
-
-
-
-
Eng-24
Temperature exchange efficiency
setting
PZ-62DR-EA/EB Setting
10 digit of temperature
check exchange efficiency
Function No. Setting Data
- 0 0
- 1 1
- 2 2
- 3 3
- 4 4
- 40 5 5
- 6 6
7
- 7
(Factory setting)
- 8 8
- 9 9
PZ-62DR-EA/EB Setting
1 digit of temperature
check exchange efficiency
Function No. Setting Data
0
- 0
(Factory setting)
- 1 1
- 2 2
- 3 3
- 41 4 4
- 5 5
- 6 6
- 7 7
- 8 8
- 9 9
.
No. 36
PZ-62DR-EA/EB Setting
The correction to
check thermistor detection
Function No. Setting Data
- 0 -7 K (-7 °C)
- 1 -6 K (-6 °C)
- 2 -5 K (-5 °C)
- 3 -4 K (-4 °C)
- 4 -3 K (-3 °C)
- 5 -2 K (-2 °C)
- 6 -1 K (-1 °C)
7
- 42 0 K (0 °C)
(Factory setting)
- 8 +1 K (+1 °C)
- 9 +2 K (+2 °C)
- 10 +3 K (+3 °C)
- 11 +4 K (+4 °C)
- 12 +5 K (+5 °C)
- 13 +6 K (+6 °C)
- 14 +7 K (+7 °C)
2303N22HHZA0013