Mitsubishi Electric LGH-15RVX3-E Installation Instructions Manual page 20

No Function
Automatic ventilation mode
53 setting 2)
The lowest outdoor temperature setting
Automatic ventilation mode
54 setting 3)
The lowest indoor temperature setting
Supply fan power up for Fan
55
speed 4
Exhaust fan power up for Fan
56
speed 4
Pre-heater output setting 1)
60
ON temperature
Pre-heater output setting 2)
61
OFF interval
LED usage setting for
62 PZ-70CSW-E during non
operation
Fan speed for air volume "High"
64
input
Fan speed for air volume "Low"
65
input
66 CO sensor or BMS setting
2
Threshold minutes for
67
PZ-70CSW-E LED
Threshold concentration for
68
PZ-70CSW-E LED
69 Emergency stop setting
70 Dx-coil unit connection selecting
Selection of the operation mode
from "Temp. priority mode" or
71
"Fan speed priority mode" with
DX-coil unit
Airflow setting for supply fan
73
speed 3
Airflow setting for supply fan
74
speed 2
Airflow setting for supply fan
75
speed 1
Airflow setting for exhaust fan
76
speed 3
Airflow setting for exhaust fan
77
speed 2
Airflow setting for exhaust fan
78
speed 1
Filter maintenance interval
83
setting - Thousands digit
Filter maintenance interval
84
setting - Hundreds digit
Lossnay core maintenance
85
interval setting - Thousands digit
Lossnay core maintenance
86
interval setting - Hundreds digit
Airflow setting for supply fan
87
speed 4
Airflow setting for exhaust fan
88
speed 4
CO sensor setting - maximum
2
89
side - Hundreds digits
CO sensor setting - maximum
2
90
side - tens digits
CO sensor setting - minimum
2
91
side - Hundreds digits
CO sensor setting - minimum
2
92
side - tens digits
93 CO sensor correction
2
Indoor negative / positive pressure
94
setting at auto fan speed setting
Indoor negative / positive pressure
95
setting at auto fan speed setting
100 Initialization (No.1～99)
This table shows the summary of function settings. Please refer to the following pages for more details.
The functions indicated with "N/A" in the "DIP-SW No." column are available only when using with remote controller PZ-62DR-EA/EB.
PZ-62DR-EA/EB can set Night purge setting (No.30), By-pass setting (No.52, 53, 54 ), CO
setting (No.83, 84), Lossnay core maintenance interval setting (No. 85, 86) and Airflow setting (No. 73-78, 87, 88) by different way more easily.
Refer to the remote controller PZ-62DR-EA/EB operation manual for more detail.
0 1 2 3
Setting Data 0 to 15 -- > Lowest outdoor temperature 10˚C to 25˚C
Setting Data 0 to 15 -- > Lowest indoor temperature 15˚C to 30˚C
N/A 1 level up 2 level up 3 level up 4 level up
N/A 1 level up 2 level up 3 level up 4 level up
0 ˚C -1 ˚C -2 ˚C -3 ˚C
1 hr 2 hrs 3 hrs 4 hrs
Unlit Lit — —
Dip-SW
Fan speed 4 Fan speed 3 —
priority
Dip-SW
Fan speed 2 Fan speed 1 —
priority
3rd party's
Dip-SW
N/A CO —
2
priority
sensor
10 min 15 min 20 min 25 min 30 min
1000 ppm 1100 ppm 1200 ppm 1300 ppm 1400 ppm 1500 ppm 1600 ppm 1700 ppm
Emergency Normal
— —
stop stop
Dx-coil unit Dx-coil
Dip-SW
is NOT unit is —
priority
connected connected
Fan speed
Temp. Fan speed
priority mode
Dip-SW
priority priority
after 1 hour
priority
mode mode temp. priority
mode
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
0 1 2 3
0 1 2 3
0 1 2 3
0 1 2 3
100 % 95 % 90 % 85 %
100 % 95 % 90 % 85 %
600 ppm 700 ppm 800 ppm 900 ppm 1000 ppm 1100 ppm 1200 ppm 1300 ppm
0 ppm 50 ppm — —
300 ppm 400 ppm 500 ppm 600 ppm 700 ppm 800 ppm 900 ppm 1000 ppm
0 ppm 50 ppm — —
-250 ppm -200 ppm -150 ppm -100 ppm -50 ppm
Supply Exhaust
N/A —
fan fan
N/A 5 % 10 % 15 %
N/A Initialize — —
Setting Data
4 5 6 7
— — —
— — —
-4 ˚C -5 ˚C -6 ˚C -7 ˚C
5 hrs — — —
— — — —
— — — —
— — — —
BMS CO sensor CO sensor
2 2
—
Pattern Z PZ-70CSW-E PZ-70CSD-E
— — —
— — — —
— — — —
Fan speed
priority mode
— — —
after 2 hours
temp. priority
mode
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
4 5 6 7
4 5 6 7
4 5 6 7
4 5 6 7
80 % 75 % 70 % 65 %
80 % 75 % 70 % 65 %
— — — —
— — — —
0 ppm 50 ppm 100 ppm
— — — —
20 % 25 % 30 % 35 %
— — — —
sensor setting (No.89, 90, 91, 92), Filter maintenance interval
2
Eng-20
2303N22HHZA0013
8 9 10 11 12 13 14
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
— — — — — — —
1800 1900 2000
— — — —
ppm ppm ppm
— — — — — — —
— — — — — — —
— — — — — — —
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
8 9 — — — — —
8 9 — — — — —
8 9 — — — — —
8 9 — — — — —
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
60 % 55 % 50 % 45 % 40 % 35 % 30 % 25 %
1400 1500 1600 1700 1800 1900 2000
ppm ppm ppm ppm ppm ppm ppm
— — — — — — —
1100 1200 1300 1400 1500 1600 1700
ppm ppm ppm ppm ppm ppm ppm
— — — — — — —
150 200 250
— — — —
ppm ppm ppm
— — — — — — —
40 % 45 % 50 % 55 % 60 % 65 % 70 % 75 %
— — — — — — —
Factory DIP-SW
setting No.
15
6 —
1 —
— 0 —
— 0 —
— 0 —
— 0 —
— 0 —
— 0 2-6
— 0 2-7
5-6
— 0 5-7
5-8
— 2 —
— 5 —
— 0 —
— 0 2-9
5-4
— 0
5-5
5 —
10 —
15 —
5 —
10 —
15 —
— 3 —
— 0 —
— 6 —
— 0 —
0 —
0 —
— 4 —
— 0 —
— 1 —
— 1 —
— 5 —
— 0 —
0 —
— 0 —