Somogyi Elektronic DBP 03 - Doorbell Manual

Table of Contents

Contents

1 OVERVIEW
2 INSTALLATION
3 REGISTERING THE BELL PUSH, CHANGING THE RINGING MELODY
4 CLEANING
5 WARNINGS
6 Documents / Resources
- 6.1 Download manual

OVERVIEW

melody selector
push-button power supply

The wireless bell push can replace old damaged, malfunctioning remote switches, can be placed at new entrances, or can be used as a pager which also operates the doorbell beside old, or handicapped people.

For replacing lost, broken push-buttons

person-calling function
variable beep
no multiple ringing with similar types
operation frequency: 433,9 MHz
256 different digital codes
range in open terrain: 200 m
16 digital channels – 8 different melodies
power supply: push-button: 1 x 3 V (CR 2032) battery (included)

INSTALLATION

Use a screwdriver to press the locking tab in the slot at the bottom of the product, then remove the back cover.
Remove the plastic insulation sheet between the battery and the battery connector.
By pushing the push button located next to the battery the melody played can be chosen from 8 different melodies.
If you wish to install the bell push using screws, before putting back the back cover, brake trough the thinned parts recessed for the screws.
Placing the name plate: remove the transparent cover on the bottom of the bell push, by using a flat object on the recessed corners. Write the desired text on the insert plate, then put back the cover.
If the range shortens, replace the battery!
The bell push needs to be installed vertically, with the name plate on the bottom!
Weather resistant design, but when placing outdoors, it is advised to provide protection against the rain.

REGISTERING THE BELL PUSH, CHANGING THE RINGING MELODY

When installing the appliance make sure, to first ensure the power supply of the bell push (as mentioned above) and only after that the indoor unit.
When putting the indoor unit into operation (as above) the device emits two short beeps, which also means that the unit is ready to receive the signal of the bell push.
Push the bell push you wish to register once, now the indoor unit emits sound and saves the unit to its memory.

If you wish to use more than one bell push, repeat the above sequence with the next unit (within 2 minutes). The maximum number of bell pushes that can be registered is determined by the receiver unit.

The device assumes 256 possible digital codes, from which it randomly chooses one, and this way guaranties that there will be no interference with similar bell push types in the vicinity.
If for any reason the unit needs to be reprogrammed, remove the battery from both units, wait for 15 seconds, and repeat the registration procedure. (At this time the appliance automatically generates another code for itself)

The appliance can be set up with 8 different melodies. With the black push button located beside the batteries of the outdoor unit the ringing melody can be changed. Every connected outdoor unit can have a different ringing melody.

CLEANING

Use a soft, dry cloth. Do not use aggressive cleaners and liquids!

WARNINGS

Walls and metal objects can shorten the range, and may interfere with its operation (metal fence, door, gate...), furthermore devices using radiofrequency can do the same (computer, microwave oven, television...).
Do not install the bell push on metal door frame, or in the vicinity of other metal surfaces!
In cold temperature the performance of the batteries will diminish, more frequent battery change may be necessary!
The main doorbell unit is only for indoor use
Do not submerge the outdoor unit into water, and do not expose it to heavy raining
Make sure, that no object or liquid can enter through the openings into the device!
Never attempt to disassemble the device, leave the repairs to a specialist!
Be careful, do not drop the device. If damaged, further use is prohibited!
Always keep the batteries away from children! If the battery is swallowed, immediately contact a doctor!
Replacing the battery can only be done by and adult!
If the batteries run out, or the device is not used for a prolonged time, remove the batteries immediately!
If the liquid has leaked out of them, put on protective gloves and with a dry cloth clean the battery compartment!
Do not open the batteries, do not throw them into fire, or short circuit them!
Protect the unit from dust, humidity, liquids, moisture, frost, shock, and from direct heat and sunshine!
Do not disassemble, or modify the device, as it can cause fire, accident, or electric shock! Improper installation, or operation invalidates the warranty.
Due to constant developments the technical data, and design can change even without prior notice.
We do not take any responsibility for possible printing errors, and are sorry if there is any.
R2 device: moderate reliability SRD telecommunication equipment, e.g. those which can cause to persons such inconveniences that cannot be solved easily with other devices.
This radioequipment adheres to the 1999/5/EK directives essential requirements. The current Declaration of Conformity is available from the somogyi@somogyi.hu e-mail address.