Advertisement
Connect to Enphase Installer Platform over Wi-Fi
11
Configuring Wi-Fi, requires a wireless router with an Internet connection.
A) If the router supports WPS, press and hold the WPS button on the wireless
router for a few seconds. On most routers, a WPS indicator begins flashing.
B) If you are using the Enphase Installer App, go to your system and tap Enphase
Installer App Step 4 (IQ Gateway connectivity), tap Wi-Fi, and then tap your
network from the list of available networks. If the wireless router does not
support WPS, you may be prompted to enter a password.
The network communications LED begins flashing green. Within three minutes
the same LED lights solid green, indicating a successful connection to Enphase
Installer App. If the Network Communications LED remains off or lights solid
red, see the "Troubleshooting" section.
12
Send system summary report
When you have completed your system setup, you can generate and email a
summary report.
The report displays IQ Gateway and system information with a list of device
serial numbers, their last power reports, and infor-
mation about the grid profile applied to the microin-
verters as shown.
Activate monitoring
13
Register the IQ Gateway in Enphase Installer App
phase.com/installerapp).
Method A: If the IQ Gateway is associated
with a system in Enphase Installer App
A ) On your mobile device, go to Settings and dis
connect from the IQ Gateway's AP Wi-Fi network.
B ) Return to the Enphase Installer App, select your system, and tap Sync on
the upper right corner.
C ) When you have access to a computer, log in to Enphase Installer Platform
and select the system name from the Activation List on the dashboard.
D ) From the activation form, open Array Builder.
If you used Enphase Installer App to build arrays and scan device serial num-
bers, the array(s) are built . Make any necessary adjustments in Array Builder.
If you did NOT use Enphase Installer App to build arrays and scan device serial
numbers, create the virtual array in Array Builder using the installation map as
your reference.
Method B: If the IQ Gateway is not associated with a system in
Enphase Installer App
A ) Log in to Enphase Installer App and click "Add a New System" from the
dashboard.
B ) Enter the System, Installer, Owner, and Location information.
C ) Enter the IQ Gateway serial number.
D ) Click "Save" to submit the form.
E ) After the devices have reported to Enphase Installer App, open Array Builder
from the activation form, and create the virtual array, using the installation
map as your reference.
(en-
Checking the Mobile Connect status LEDs
The modem has the following status LEDs
• Power
• Link
• Signal
The following tables list LED indicator status. The LEDs may be difficult
to see if you view them from an angle. View the LEDs straight on.
Power
LED
Off
DC power not present
On
DC power present
Link
LED
Flashing slowly
(200 ms high/1800 ms low)
Flashing slowly
(1800 ms high/200 ms low)
Flashing quickly
(125 ms high/125 ms low)
Signal
LEDs
Description
All off
Bar 1 ON
Bar 1 and 2 ON
Bar 1, 2, and 3 ON
Troubleshooting
Issue
No communica-
1. Disconnect the USB cable.
tion with Enphase
2. Power cycle the IQ Gateway.
Installer App after
3. Wait until the IQ Gateway boots
connecting the
completely.
cellular modem to
the IQ Gateway.
4. Reconnect the cellular modem USB cable.
I want to disconnect
Moving the modem to a different IQ Gate-
the modem and
way deactivates the modem. Contact
re-use it at a different
Enphase customer support if you need to
site.
re-install the modem at a different site.
Indicates
Indicates
Network searching
Idle
Data transfer is occurring
Indicates
Very weak signal
Weak signal
Good signal
Very good signal
Action
Advertisement
