Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RF-Star RF-ZM-2530P1 CC2530
Summary of Contents for RF-Star RF-ZM-2530P1 CC2530
- Page 1 RF-ZM-2530P1 and RF-ZM-2530P1I CC2530 with PA CC2592 Low-Power 2.4 GHz IEEE 802.15.4 and ZigBee Module Version 1.0 Shenzhen RF-star Technology Co., Ltd. Mar. 22 , 2023 All rights reserved. Those responsible for unauthorized reproduction will be prosecuted.
-
Page 2: Device Overview
(one 16-bit, two 8-bit) 1.3 Applications • 2.4 GHz IEEE 802.15.4 systems • Home automation • RF4CE remote control systems • Building automation • ZigBee systems • Industrial control and monitoring Shenzhen RF-star Technology Co., Ltd. Page 1 of 24... -
Page 3: Functional Block Diagram
Power Filter Reset 2.0 V ~ 3.6 V IPEX Connector GPIO CC2592 CC2530 Debug Chip Antenna Matching Switch Half-Hole Interface 32.0 MHz 32.768 kHz Figure 2. Functional Block Diagram of RF-ZM-2530P1I Shenzhen RF-star Technology Co., Ltd. Page 2 of 24... -
Page 4: Part Number Conventions
The part numbers are of the form of RF-ZM-2530P1/P1I where the fields are defined as follows: RF ZM 2530 Antenna Type Company Name IPEX connector RF-STAR Module Version The First Version Chipset Wireless Type ZigBee Module TI CC2530 Figure 3. Part Number Conventions of RF-ZM-2530P1/P1I Shenzhen RF-star Technology Co., Ltd. Page 3 of 24... -
Page 5: Table Of Contents
5.6 Basic Operation of Hardware Design ...................... 17 5.7 Trouble Shooting .............................. 18 5.7.1 Unsatisfactory Transmission Distance ..................18 5.7.2 Vulnerable Module ..........................19 5.7.3 High Bit Error Rate ..........................19 5.8 Electrostatics Discharge Warnings ......................19 Shenzhen RF-star Technology Co., Ltd. Page 4 of 24... - Page 6 RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 5.9 Soldering and Reflow Condition ......................... 19 6 Optional Package Specification ..........................21 7 Revision History ................................23 8 Contact Us ..................................24 Shenzhen RF-star Technology Co., Ltd. Page 5 of 24...
-
Page 7: Module Configuration And Functions
RF-ZM-2530P1: PCB antenna Type of Antenna RF-ZM-2530P1I: IPEX connector/Half-hole ANT pin Package SMT packaging (1.27-mm half-hole pitch stamp stick) Operating Temperature -40 ℃ ～ +85 ℃ Storage Temperature -40 ℃ ～ +125 ℃ Shenzhen RF-star Technology Co., Ltd. Page 6 of 24... -
Page 8: Module Pin Diagram
Port 2.1/Connect to the DD of CC Debugger P2_0 Digital I/O Port 2.0 P1_7 Digital I/O Port 1.7 P1_6 Digital I/O Port 1.6 Ground P1_5 Digital I/O Port 1.5 P1_4 Digital I/O Port 1.4 Shenzhen RF-star Technology Co., Ltd. Page 7 of 24... - Page 9 Port 1.5 P1_4 Digital I/O Port 1.4 P1_3 Digital I/O Port 1.3 P1_2 Digital I/O Port 1.2 P1_1 Digital I/O Port 1.1 P1_0 Digital I/O Port 1.0 P0_7 Digital I/O Port 0.7 Shenzhen RF-star Technology Co., Ltd. Page 8 of 24...
- Page 10 P0_4 Port 0.4 Digital I/O P0_4 Digital I/O Port 0.3 P0_2 Digital I/O Port 0.2 P0_1 Port 0.1 Digital I/O P0_0 Port 0.0 Digital I/O Ground Ground External ANT pin Ground Shenzhen RF-star Technology Co., Ltd. Page 9 of 24...
-
Page 11: Specifications
3.2 Handling Ratings Table 5. Handling Ratings of RF-ZM-2530P1/P1I Items Min. Typ. Max. Unit Condition Storage Temperature +125 ℃ Tstg Human Body Model ±2000 Moisture Sensitivity Level Charged Device Model ±500 Shenzhen RF-star Technology Co., Ltd. Page 10 of 24... -
Page 12: Application, Implementation, And Layout
RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 4 Application, Implementation, and Layout 4.1 Module Photos RF-ZM-2530P1 RF-ZM-2530P1I Figure 5. Photos of RF-ZM-2530P1/P1I 4.2 Recommended PCB Footprint RF-ZM-2530P1 Shenzhen RF-star Technology Co., Ltd. Page 11 of 24... -
Page 13: Schematic Diagram
RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 RF-ZM-2530P1I Figure 6. Recommended PCB Footprint of RF-ZM-2530P1/P1I (mm) 4.3 Schematic Diagram RF-ZM-2530P1 Shenzhen RF-star Technology Co., Ltd. Page 12 of 24... -
Page 14: Reference Design Of Rf-Bm-2530P1/P1I
RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 RF-ZM-2530P1I Figure 7. Schematic Diagram of RF-ZM-2530P1/P1I 5.4 Reference Design of RF-BM-2530P1/P1I Figure 8. Reference Design of RF-ZM-2530P1 Shenzhen RF-star Technology Co., Ltd. Page 13 of 24... -
Page 15: Antenna
Therefore, the layout of the module antenna location and routing is recommended as follows: (1) Place the antenna on the edge (corner) of the PCB. (2) Make sure that there is no signal line or copper foil in each layer below the antenna. Shenzhen RF-star Technology Co., Ltd. Page 14 of 24... -
Page 16: Antenna Output Mode Modification Of Rf-Zm-2530P1I
The traces are as short as possible, and 135° or arc traces are used as much as possible. No vias are used to change layers. More GND vias are placed around the RF traces. Shenzhen RF-star Technology Co., Ltd. Page 15 of 24... - Page 17 Example: FR4 is a double-layer board with a thickness of 1.0 mm. Through calculation, the width of the trace is 0.8254 mm, and the spacing between traces and copper is 0.22 mm. Figure 14. SI9000 Impedance Calculation Diagram Shenzhen RF-star Technology Co., Ltd. Page 16 of 24...
-
Page 18: Ipex Connector Specification
1. It is recommended to offer the module a DC stabilized power supply, a tiny power supply ripple coefficient, and reliable ground. Please pay attention to the correct connection between the positive and negative poles of the power Shenzhen RF-star Technology Co., Ltd. Page 17 of 24... -
Page 19: Trouble Shooting
4. The incorrect power register set or the high data rate in the open air may shorten the communication distance. The higher the data rate, the closer the distance. Shenzhen RF-star Technology Co., Ltd. Page 18 of 24... -
Page 20: Vulnerable Module
3. If the extension wire or feeder wire is of poor quality or too long, the bit error rate will be high. 5.8 Electrostatics Discharge Warnings The module will be damaged by the discharge of static. RF-star suggests that all modules should follow the 3 precautions below: 1. - Page 21 Max. 6 ℃/s Time from 25 ℃ to Peak Temperature (t Max. 6 minutes Max. 8 minutes Time of Soldering Zone (t 20±10 s 20±10 s Figure 17. Recommended Reflow for Lead-Free Solder Shenzhen RF-star Technology Co., Ltd. Page 20 of 24...
-
Page 22: Optional Package Specification
The default package method is . If you need the modules to be shipped by tape & reel, pls contact us in advance. Figure 18. Default Package by Tray Shenzhen RF-star Technology Co., Ltd. Page 21 of 24... - Page 23 RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 Figure 19. Package by Tape & Reel Shenzhen RF-star Technology Co., Ltd. Page 22 of 24...
-
Page 24: Revision History
1. The document will be optimized and updated from time to time. Before using this document, please make sure it is the latest version. 2. To obtain the latest document, please download it from the official website: www.rfstariot.com and www.szrfstar.com. Shenzhen RF-star Technology Co., Ltd. Page 23 of 24... -
Page 25: Contact Us
RF-ZM-2530P1/P1I www.szrfstar.com V1.0 - Mar., 2023 8 Contact Us SHENZHEN RF-STAR TECHNOLOGY CO., LTD. Shenzhen HQ: Add.: Room 502, Podium Building No. 12, Shenzhen Bay Science and Technology Ecological Park, Nanshan District, Shenzhen, Guangdong, China, 518063 Tel.: 86-755-8632 9829 Chengdu Branch: Add.: N2-1604, Global Center, North No.
Need help?
Do you have a question about the RF-ZM-2530P1 CC2530 and is the answer not in the manual?
Questions and answers