1. Manuals
  2. Brands
  3. Trotec Manuals
  4. Grinder
  5. PAGS 11-125
  6. Original instructions manual

Trotec PAGS 11-125 Original Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PAGS 11-125
EN
ORIGINAL INSTRUCTIONS
ANGLE GRINDER

Advertisement

Table of Contents
loading

Related Manuals for Trotec PAGS 11-125

Summary of Contents for Trotec PAGS 11-125

  • Page 1 PAGS 11-125 ORIGINAL INSTRUCTIONS ANGLE GRINDER...

  • Page 2: Table Of Contents

    (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the instructions must be observed. angle grinder PAGS 11-125...

  • Page 3: Safety

    Use of dust collection can earthed or grounded. reduce dust-related hazards. • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. angle grinder PAGS 11-125...
  • Page 4 Damaged accessories will normally break apart during this test time. angle grinder PAGS 11-125...
  • Page 5 Such blades create frequent kickback materials. Sparks could ignite these materials. and loss of control. • Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. angle grinder PAGS 11-125...
  • Page 6 Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding. angle grinder PAGS 11-125...
  • Page 7 It is safer to handle the power tool with two hands. We recommend using the power tool with original Trotec • For accessories with internal threads such as brushes accessories.
  • Page 8 3. Do not reconnect a defective device to the mains. working with a power tool. If necessary, use a pipe detector to check the wall you want to drill in or slit open. Warning Risk of injuries caused by flying parts or bursting tool heads. angle grinder PAGS 11-125...

  • Page 9: Information About The Device

    • 1 x Cutting disc for metal, cutting disc diameter: 125 mm • 1 x Guard • 1 x Additional handle • 1 x Pin-type face wrench • 1 x Clamping nut • 1 x Transport case • 1 x Manual 13 12 angle grinder PAGS 11-125...

  • Page 10: Transport And Storage

    This can reduce the vibration load over the entire work period significantly. angle grinder PAGS 11-125...

  • Page 11: Start-Up

    1. Screw the additional handle (10) clockwise into the thread (2) either on the right- or left-hand side or on top of the housing. 2. Check the additional handle (10) for tight fit. 3. For disassembly unscrew the additional handle (10) counter-clockwise. angle grinder PAGS 11-125...
  • Page 12 It must be impossible to rotate the guard. workpiece. The closed side of the guard must always point You can increase the clamping force of the lock by to the user. tightening the adjusting screw (11). 3. Close the locking lever (13). angle grinder PAGS 11-125...
  • Page 13 The labelling must point to the device. Make sure that the 3. Use the pin-type face wrench (17) to unscrew the cutting disc hole fits the mounting flange without clamping nut (16) counter-clockwise. Then let go of the clearance. Do not use any reducers or adapters. spindle lock (1). angle grinder PAGS 11-125...
  • Page 14 You can change the preselected speed level at any time. Pay attention not to damage the cutting disc. 1. Turn the setting wheel (3) to the desired rated speed level. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. angle grinder PAGS 11-125...

  • Page 15: Operation

    • You'll obtain better results if the machining process not only involves one single work cycle, but if you move over the surface several times with the tool. To do so, use a positioning angle of approx. 30°. angle grinder PAGS 11-125...

  • Page 16: Available Accessories

    Designation Article number Cutting/roughing disc set Ø 125 mm 6.225.001.131 Cutting disc set diamond Ø 110 mm / 115 mm 6.225.001.121 Cutting disc metal Ø 125 mm 6.225.001.111 Cutting disc stone Ø 125 mm 6.225.001.101 angle grinder PAGS 11-125...

  • Page 17: Errors And Faults

    • Make sure that the clamping nut (16) is firmly tightened, see chapter Tool change. • Make sure that there is no workpiece debris blocking the drive. Remove the blockages, if any. • Make sure that the cutting disc is not jammed in the workpiece. angle grinder PAGS 11-125...

  • Page 18: Maintenance

    Maintenance tasks which require the housing to be Always replace the carbon brushes in pairs. opened must only be carried out by authorised specialist companies or by Trotec. ü Make sure to have a pair of unused carbon brushes ready. Notes on maintenance ü...
  • Page 19 7. Repeat this process on the other side of the device. Note Before switching the device on, the contact connector must be connected; otherwise the device can be damaged. angle grinder PAGS 11-125...

  • Page 20: Disposal

    The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life.
  • Page 21 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...

Table of Contents